I worked on my honda for the first time and broke a bolt on the valve cover. Smh. Glad this video was made. I even listened to the same song just for extra luck.
As a mechanic, I come across broken bolts often and spend crazy time to removing them. Your method, will work better than an extraction tool that often does not work. Thank you.
Worked like a charm, thank you!!! I had a broken bolt in the head of my 454. Used 7/64 for a pilot hole & then a 7/32. #27 torn & it came out as smooth as butter. You ROCK!
Dude my lq9 in my truck. Got all bolts free. Then noticed a bolt was missing. Looked and shit is broken flush on my head. So 7/64 then go to 7/32 then t27?? Fuck. My engine is in place. I can remove the wheel well and gain access. Luckily I’m small enough to fit and work. I just have to remove heat shields. This shit has been lingering in my head since thanksgiving man lol
Just had to add my comment since this saved my ass. Had a speed sensor bolt that broke off in the steering knuckle. It was a fairly small 10mm bolt head to give you an idea. Used a 3/32 drill bit and a smaller T10 torx (figured I'd start there and go bigger if I needed). Didn't drill too deep for fear of not drilling perfectly straight, worked like a charm. Thought I'd throw my testimonial and numbers here in case it helps
Bro i love you so much for this. Im a Machinist and ive been trying to get a headless thread out for like 2hrs. My shop doesnt have thread extractors, so i looked up your vid and it just saved my ass! Without your video, i wouldve had to scrap a $900 mutli inserted drill shank. Take my sub and like even if you never make another video
Great vid and very informative. I had a similar situation with an exhaust bolt. What helped me was using a left hand drill bit. It hollowed out the hole as well as loosing it up. As soon as I put the easy out in the bolt it was loose enough to loosen by hand .
@@jio7270 Im trying to change my wheel cylinder and the T8 Torx bolt got really rounded cause I wasn't using the right size like an idiot then I tried using other types of sockets now im fucked. Beatin the shit out of it with a punch
@@wildside1951 see if its a torx head, go up a size or two, in your case a t10 would probably be best, but put the bit on the head roughly in the same pattern and beat the hell out of it until you fit the bit in there, that usually helps me undo a stripped torx screw
Thank you good sir for this video. This video saved me. Had a broken bolt stuck in a valve cover. I managed to get it out. Thank you for your guidance. ✌️
Cool! By using this method I should be able to drive the broken bolts that held my ATV's skid plate to the frame out by reversing direction and actually driving them deeper in until they come out the other side.
Thanks for this video!!!! I bought a ez out kit and it couldn’t get the bolt out but I used your method with a torx bit and it worked out better thanks again for the video 👌👌👌👍👍👍👍👍👍🙌🙌🙌🙌🙌🙌
I have a bleed valve snapped off in the caliper. Most videos say weld a nut on the end. I can't weld so hopefully this approach will work. Thanks for the vid
I going trying it but slightly smaller broken bolt. That one thing I dislike when tightening a Bolt it seems not to be tightening but all the of a sudden u hear a Tink.
Não tô conseguindo tirar parafusos do compressor de ar direto ele nunca foi aberto e nunca teve manutenção e eu já espanei todos os parafusos de tanto tentar tirar porque eles estão bem emperrados que nem se me chamou. .alguém me da um dica que funciona
thank you for your comment I invite you to see and share: czcams.com/video/5NexmjaQEg8/video.html I'm from Catalonia, I like to share my little experiences, if you like enter between channels, you will see funny situations REGARDS
Yes, man! Many tools come to make working easier. In 2000 I was working as a mechanic and did it same way. Now I'm saling car repair tools including screw extraclors. czcams.com/video/-IFIGwZckt0/video.html The only problem of TORX, if finally it will get broken inside hole it will be double trouble to extract it. So, doing this way should be very carefull with the torque you use for unscrewing.
I used this method with limited success using an impact rated T30 bit. While trying to remove one broken stud which was below the surface, I managed to snap off the end of the bit. I just happened to have a 7mm diamond core bit handy (about $8). While time consuming, I was able to drill and expose enough of the broken bit to remove it. Hope someone finds this rescue tip helpful.
How do u get it out if the head it alread broke and the threads are in there flush. My rotor screw is broken into the wheel hub and I can’t put a new screw to line everything up. And now the brake caliper is rubbin I’m rotor. This screw is very tiny
Thank you for your comment, if you like the mechanics, I invite you to visit my channel and if it convinces you, I encourage you to subscribe. Greetings from Catalonia
Well I’m going to attempt this now I’ll let you know in a little bit how it went Edit: 12 hours later and I’ve got it out with my drill by just attaching the end of the broken screw I got to stick out enough straight to my drill and put her into reverse bam screw is out It was for my thermostat so big pain to get to but I got the job done
www.amazon.es/dp/B07Z628TRZ/ref=cm_sw_r_cp_apa_i_hZDREb9T078FZ Gracias por comentar si le apetece puede visitar mi canal puede suscribirse es gratis· si lo hace no se olvide de darle a la campaña. SALUDOS
Gracias por comentar le invito a ver: czcams.com/video/5NexmjaQEg8/video.html Si ha sido de su interés puede a suscribirse a mi canal, gracias y. SALUDOS
Al final no he tenido más remedio que suscribirme a su canal porque he visto en sus videos que somos iguales, con las mismas inquietudes y llevo también muchos años compartiendo mis esperiencias con el prójimo como Ud dice, eso es lo importante "COMPARTIR" que parece que hoy en día solo valen las exclusivas y el dinero, pues no...yo pienso como usted.
You're a lifesaver. I spent an hour using an extractor and this method took me all of 5 minutes. About to pick up a set of torx sockets
I worked on my honda for the first time and broke a bolt on the valve cover. Smh. Glad this video was made. I even listened to the same song just for extra luck.
Same issue with honda car boss
Me im experiencing this hays 10 size valve cover bolts
@@JDMSTRT qxx""""“0
Mine is on my Zero Turn's starter bolt 😑
📻 Another one bites the dust... (Tools breaking)
As a mechanic, I come across broken bolts often and spend crazy time to removing them. Your method, will work better than an extraction tool that often does not work. Thank you.
Gracias por su comentario, le invito a ver:
czcams.com/video/sLl7-k9334Y/video.html
SALUDOS
Facts
Probably one of the most useful Videos on CZcams..... saved me a trip to the hardware store and the cost of a bolt extractor!
Worked like a charm, thank you!!!
I had a broken bolt in the head of my 454. Used 7/64 for a pilot hole & then a 7/32. #27 torn & it came out as smooth as butter.
You ROCK!
Dude my lq9 in my truck. Got all bolts free. Then noticed a bolt was missing. Looked and shit is broken flush on my head. So 7/64 then go to 7/32 then t27?? Fuck. My engine is in place. I can remove the wheel well and gain access. Luckily I’m small enough to fit and work. I just have to remove heat shields.
This shit has been lingering in my head since thanksgiving man lol
pulled me out of a deep mess as i had a set of long torques all the extractors to short you vid saved the day
many thanks
Just had to add my comment since this saved my ass. Had a speed sensor bolt that broke off in the steering knuckle. It was a fairly small 10mm bolt head to give you an idea. Used a 3/32 drill bit and a smaller T10 torx (figured I'd start there and go bigger if I needed). Didn't drill too deep for fear of not drilling perfectly straight, worked like a charm. Thought I'd throw my testimonial and numbers here in case it helps
Store bought extractors were not working. This method actually worked great! Thanks!
I spent over 50.00 in Bolt Remover kits that didn't work, but this did. Thank you!
Bro i love you so much for this. Im a Machinist and ive been trying to get a headless thread out for like 2hrs. My shop doesnt have thread extractors, so i looked up your vid and it just saved my ass! Without your video, i wouldve had to scrap a $900 mutli inserted drill shank.
Take my sub and like even if you never make another video
Great vid and very informative. I had a similar situation with an exhaust bolt. What helped me was using a left hand drill bit. It hollowed out the hole as well as loosing it up. As soon as I put the easy out in the bolt it was loose enough to loosen by hand .
Oh my goodness you Rock I had that screw out in less than 10 minutes best advice ever 💯
Hell, might as well give it a try. I ain't done nothing but screw it up so far.
Nice one
Exactly where I’m at lmao
Bro im changing the fucking brakes on my car and the caliper bolt head snaps off😐
@@jio7270 Im trying to change my wheel cylinder and the T8 Torx bolt got really rounded cause I wasn't using the right size like an idiot then I tried using other types of sockets now im fucked. Beatin the shit out of it with a punch
@@wildside1951 see if its a torx head, go up a size or two, in your case a t10 would probably be best, but put the bit on the head roughly in the same pattern and beat the hell out of it until you fit the bit in there, that usually helps me undo a stripped torx screw
Thank you good sir for this video. This video saved me. Had a broken bolt stuck in a valve cover. I managed to get it out. Thank you for your guidance. ✌️
Gracias por comentar le invito a visitar mi canal y compartir.
czcams.com/video/AA39g06iy5I/video.html
saludos
This works like a charm! Just extracted two snapped manifold studs from my RB25DET head!
Saved me from catastrophe . Thank you so much.
I did it and it work. Thank you for this video. Very helpful
Best video on CZcams for this.Straight to the point and also have good music
What is the song I like the music also
used this on spark plugs works a treat, saves loads time
OMG you came so close to fooking up your inner threads, Thank God you didn't or this would of been another video.
Good stuff, Thanks for sharing.
Cool! By using this method I should be able to drive the broken bolts that held my ATV's skid plate to the frame out by reversing direction and actually driving them deeper in until they come out the other side.
Got a new sub cuz I just came across this problem 😂😂
Thanks for this video!!!! I bought a ez out kit and it couldn’t get the bolt out but I used your method with a torx bit and it worked out better thanks again for the video 👌👌👌👍👍👍👍👍👍🙌🙌🙌🙌🙌🙌
Thanks! Just saved me so much work. Didnt even know that we could use those bits on a ratchet. Thanks
Gracias por comentar!
Si le gusta la mecànica le invito a visitar mi canal.
SALUDOS
You are a life saver. This was the cheapest most effective method.
Simple dude with a simple toolbox getting it done. 👍
czcams.com/video/5NexmjaQEg8/video.html
Le invito a ver y compartir.
SALUDOS
Wow! I’m going to try this method. Thank you. 👌🏾
I have a bleed valve snapped off in the caliper. Most videos say weld a nut on the end. I can't weld so hopefully this approach will work. Thanks for the vid
enter my channel you can find the solution
Same situation happen to me now. How about yours? Can you extract the snapped screw?
Lol.... happened to me too..... i said to hell with that and bought a new caliper instead.
Happened to me a while back we fixed it by plugging it with a nail lol
I going trying it but slightly smaller broken bolt. That one thing I dislike when tightening a Bolt it seems not to be tightening but all the of a sudden u hear a Tink.
Very good, the best and simply solution that j've saw just until now.
czcams.com/video/d_ohxQT--ic/video.html
Le invito a ver.
Saludos
Thank you so much, im from Brazil It worked
so satisfying to watch it unscrew
Right on brother good hack. Use this on my John Deere lawnmower and it came out just perfect didn’t even have to go buy a kit thank you brother!!!👍😎
thanks for comment
If you like mechanics, I invite you to visit my channel
czcams.com/channels/PP14v9RHOnCif52XqhGZ0g.htmlvideos
I will brother thanks for the info stay safe
Thanks brother this helped me. Easy out wasn’t working for me. I’m so happy 😁🤙
You absolute legend. This saved me so much hassle.
very helpful!!! i have a broken pcv valve and the thread part is in the valve cover hole gonna try with torx bits
Thank you worked a treat, saved me from a massive mess
Excellent video! Thanks!
Excellent video
Não tô conseguindo tirar parafusos do compressor de ar direto ele nunca foi aberto e nunca teve manutenção e eu já espanei todos os parafusos de tanto tentar tirar porque eles estão bem emperrados que nem se me chamou. .alguém me da um dica que funciona
Videos like these is why i love youtube
Thanks for commenting, I invite you to visit my channel and see.
Cómo sacar extraer un tornillo perno roto partido en lugar difícil.
SALUDOS
This worked for me perfectly. I used a smaller size drill bit and a smaller size torx.
No no no. Must use left turn drill. I have had them spin out before using easyout. A right turn drill drives in further.
Getting broken bolts out is so satisfying
Thank you for posting. Going to give this a try.
That was very satisfying to watch.
Worked like a charm! Thx sooo much!!🙏🏽🙏🏽
thank you for your comment I invite you to see and share:
czcams.com/video/5NexmjaQEg8/video.html
I'm from Catalonia, I like to share my little experiences, if you like enter between channels, you will see funny situations
REGARDS
God blesss this man
It was hard for me to drill it so I used metal screw and the star bit and booom
Thats awesome, I was figuring out how to deal with such bolt.
Thanks 👍
Mine is small bolt sand I guess I can't drill its like ,,8 mm Dia bolt in KTM ',s oil filter side cover
@@yousufmusthaneer9738
Do as he did, use 3mm and then 4mm, and don't forget to use lubricant before final step of removal.
Nice.I definitely feel better just knowing some one else had success.
valeu muito a dica, retirei o parafuso com muitissima facilidade, parabens e muito obrigado
So cool. Now I know I'm not the only one who ends up with a off center hole.
Better then the torques bit braking in with the stud now I can't drill it
well done. Fantastic work.
Best part about this technique is that it can be applied to left and right-handed bolts.
You just saved me time, aggravation and money... Worked like a charm, thank you!
czcams.com/video/AA39g06iy5I/video.html
Thanks for comment.
I invite you to see my videos share them.
Greetings
It work perfect, thanks and I did subscribe to your channel.
mine hasnt broken in a flat manner. gonna try this anyway. good vid
yes, I was doing that way 20 years ago before came out first extractors on the market :)
Yes, man! Many tools come to make working easier. In 2000 I was working as a mechanic and did it same way. Now I'm saling car repair tools including screw extraclors. czcams.com/video/-IFIGwZckt0/video.html
The only problem of TORX, if finally it will get broken inside hole it will be double trouble to extract it. So, doing this way should be very carefull with the torque you use for unscrewing.
I tried it and it work as described, awesome 😎
Finally what I was looking for but got no dam drill damit
Ommggg fr
This video shows a good reason to own a torque wrench
I am curious as to why threads that clean would have caused a bolt to snap from extraction?
Thanks man helped a lot had to use a different bit but same idea
I will try this on my brake caliper bolt that broke on my knuckle 😢 thank you very much
Thanks man your video helped me an my brother a lot 👏👏👏you are awesome 👏👏👏
czcams.com/video/AA39g06iy5I/video.html
Saludos Gracias
Worked me for, thank you so much!
czcams.com/video/AA39g06iy5I/video.html
gracias por su comentario, le invito a ver i compartir
SALUDOS
Very useful. Nice. Very infomational.👍
Both the screws holding my mass airflow sensor snapped when I was taking it out to clean it... Ugh. I hope this helps!
Gracias por comentar.
Saludos y suerte
Gracias por este vídeo, resolví lo de un perno roto igual al del vídeo y salió fácil
Gracias por el comentario.
Le invito a visitar mi canal y suscribirse.
SALUDOS
your method is much better, i think. I will try using it. thanks
I used this method with limited success using an impact rated T30 bit. While trying to remove one broken stud which was below the surface, I managed to snap off the end of the bit.
I just happened to have a 7mm diamond core bit handy (about $8). While time consuming, I was able to drill and expose enough of the broken bit to remove it. Hope someone finds this rescue tip helpful.
Bonjour et merci énormément sa ma sauvé la vie vraiment le top vous êtes un génie bonne continuation merci encore
Thank you Mr.!
Worked great cheers 🍻
Man listen you just saved me so much money bro 😂 thank you for that hack 🙏 🙌
Wow good tutorial👍
I need to fix my car but I can't stop grooving to the tune man !
Lol
Thanks brother you saved me money and time
How do u get it out if the head it alread broke and the threads are in there flush. My rotor screw is broken into the wheel hub and I can’t put a new screw to line everything up. And now the brake caliper is rubbin I’m rotor. This screw is very tiny
Claro si el motor esta afuera
Hell yes this video saved me big hubk of time and money. 66 Dollars to be exact. Bless
Awesome...quick and to the Point
Thank you for your comment, if you like the mechanics, I invite you to visit my channel and if it convinces you, I encourage you to subscribe.
Greetings from Catalonia
Yes ! J'ai pris cette méthode et c'est super et simple et marche super bien
Gracias por comentar si le apetece puede visitar mi canal.
SALUDOS
Going to try this tomorrow
I did this method not even seen this video, works well
I thought I've seen it all ,good one.
Great idea 👍
Well I’m going to attempt this now I’ll let you know in a little bit how it went
Edit: 12 hours later and I’ve got it out with my drill by just attaching the end of the broken screw I got to stick out enough straight to my drill and put her into reverse bam screw is out
It was for my thermostat so big pain to get to but I got the job done
czcams.com/video/5NexmjaQEg8/video.html
Le invito a ver y compartir
SALUDOS
Lol, cutting it close but looks like good method on the cheap too
HOLY $HIT I LOVE YOU!!! THIS LITERALLY SAVED MY ASS.
czcams.com/video/5NexmjaQEg8/video.html
Le invito a ver y compartir.
GRACIAS Y SALUDOS desde Catalonia
Genius. I just removed a stripped flat head screw out of a 60amp breaker
Best video Ever! Worked 4 me!
Why not just drill with the 4mm drill bit first instead of starting with the 3mm?
Yes it worked first go ! Thankyou !
That looks like it will work for the problem I have. Thanks.
Lucked out. The screw was not in a blind hole and came out when drilled. Thanks for tip anyways
Me alegro tuviera poca dificultad.
Gracias por su comentario.
Le invito a visitar mi canal.
SALUDOS
Hola ,que tal?Quiesiera preguntar que marca de torx esta utilizando para sacar los tornillos?
www.amazon.es/dp/B07Z628TRZ/ref=cm_sw_r_cp_apa_i_hZDREb9T078FZ
Gracias por comentar si le apetece puede visitar mi canal puede suscribirse es gratis· si lo hace no se olvide de darle a la campaña.
SALUDOS
It's work!!! Bravo!
Gracias por comentar le invito a ver:
czcams.com/video/5NexmjaQEg8/video.html
Si ha sido de su interés puede a suscribirse a mi canal, gracias y.
SALUDOS
Al final no he tenido más remedio que suscribirme a su canal porque he visto en sus videos que somos iguales, con las mismas inquietudes y llevo también muchos años compartiendo mis esperiencias con el prójimo como Ud dice, eso es lo importante "COMPARTIR" que parece que hoy en día solo valen las exclusivas y el dinero, pues no...yo pienso como usted.
Good tactik dude
what if your t-27 breaks off too