Control DC Motor using Flysky without Brushed ESC and Arduino | DIY brushed ESC using servo and BTS🔥
Vložit
- čas přidán 28. 08. 2024
- Hi Guys,
This video will show you how to control DC motor from flysky and BTS driver without using Arduino and ESC. Hope you like it!!
Circuit: drive.google.c...
-*-*-*-*-*-*-*-*
Useful Links:
Arduino Tutorial For beginners: • Arduino tutorials for ...
Roborace Robot using Arduino and BTS7960: • Roborace Robot using A...
*-*-*-*-*-*-*-*-*
Product Links:
Servo motor: www.flyrobo.in...
BTS7960: www.flyrobo.in...
Flysky fs-i6 Tx Rx: www.flyrobo.in...
Johnson gear motor: www.flyrobo.in...
OR
Servo motor: amzn.to/3V8DMNJ
BTS7960: amzn.to/3yRSnpj
500 rpm Johnson gear motor : amzn.to/3jDnrlq
Flysky fs-i6 Tx Rx: amzn.to/4em7acn
*-*-*-*-*-*-*-*-*-*-*-*
Follow us on Instagram :
/ tech_at_home
Like us on Facebook :
/ tech-at-home-220885266...
#dcmotor #flysky #bts7960 #servo #esc #ebike #roborace #robosoccer #techfest #ArduinoTutorials #techathome #arduinoprojects
Thanks for watching!
*Like Share and Subscribe - Věda a technologie
![LPG gas leakage detection system using Arduino[with CODE] | LPG leakage safety project with auto off](http://i.ytimg.com/vi/wYqUyaEY9sk/mqdefault.jpg)
![LPG gas leakage detection system using Arduino[with CODE] | LPG leakage safety project with auto off](/img/tr.png)
Bro, Good use of servo motor for running roborace robots without arduino. But how many motors can we control with this motor driver without having a heating issue in motor driver?
@@RoboAntXOR ok bro thanks for your reply.
You can use upto 43A
Hi, your videos are very good. Please make a video using 24v 250w motors using the same process , without Arduino Uno
Thank you ❤️
There is no difference in the setup.
Instead of this motor you can connect 24v motor.
Also in place of 12v, connect 24v supply.
This BTS driver can handle without any issues.
Great video! When you move your stick you get different speeds on your motor. But when I'm using this method with 24v I'm only getting either 24v or -24v from the motor output on the board. So the motor is only ON or OFF. Shouldn't I get different outputs depending on stick and potentiometer positions?
Thank you!!
It should work the same way with variable speed. You will only use 24v motor and respective supply. This any way motor driver will handle.
Did you try to run the motor or only measured the output voltage???
@@techathome I both measured and run the motor. Strange...
You can check once if pwm control of your BTS driver is working properly or not. Refer this video: czcams.com/video/H2YJRaaXFIM/video.htmlsi=TTUn0lGqQFr1tFv5
If this is not the issue, then the circuit from servo might be an issue. Only these two possibilities.
Hey bro pls reply for this i need solution for this definitely.....so pls
.......
The problem is: While i asked you, can we use 4 10koem potenciometers for accelerator,brake,clutch and steering and 7 spdt micro switch with roller lever for h shifter all in the same arduino board in your ffb steering for my 900 degree wheel....you said ,yes you can use same arduino for all....but i have taken 5v from arduino to a pin of bread board.....and a ground pin also...
Now spdt switches (hshifter) needs 7 grounds and potenciometers needs 4 gnd(s) and 4 5volts pins......so if i connect this two ....my arduino turns off , so what should i do .......i have only one arduino ,but i should complete it with one arduino......pls reply very fast very fast pls😢😢😢😢😢😅😅😅😭😭😭😭😭💔😵😵
And another question,should we use a common gnd and a common 5volt for all the 4 potenciometers????😅😅
I am confused.
If you are using Arduino uno, it is not FFB.
Yes you can same Uno board for all.
You can send mail: deepakhd20@gmail.com
Bro can we use for reducing 12v to 5v. By using AMS 1117 5v step down power supply module. Please reply. New subscriber❣️🤍
Yes you can use any of the step down converter.
No specific one.
@@techathome can you suggest a dc motro for rc boat big size. Its cm about 100 cm. I used vrushelle but its eac burn. Now this time i am thinking to make with dc motor. With this type of esc.
Yes you can use this method, it's very easy.
BTS driver can control upto 24v, 40A DC motors.
You can go with ebike motors without gear both 12 and 24v available.
Check this mode if it is sufficient : MY6812, 12v, 120W
Bro controller buy link at very low price.😢
I found for 10 dollars
800 rupees only🤯. Please send me link
Which controller are you referring??
The Same one which is in the video. 6 channel flysky fs-i6
Bro please make a video about espnow protocol 🥲
👍
Bro my arduino uno is Not getting power supply
..... Is there any solution Available to solve this pls....😅😅😅😢😢😢😢
I didn't get.
Which video are you referring?
@@techathome The one you made i.e 900 degree steering wheel.......but i fixed it it's just a wire problem thank you...
👍