Velikost videa: 1280 X 720853 X 480640 X 360
Zobrazit ovladače přehrávání
Automatické přehrávání
Přehrát
Don't forget to reconnect your fuel lines. :)
Yes, that's the tricky bit & it did'nt get shown.. what a shame.😬
Super fain. Ai reinviat monstrul de crengi..Am tăiat 10 ani cu asa ceva de la crengi până la arbori de 80 cm 😈 te salut Ady, toate cele bune. Big 👍
Multumesc John, sunt bune drujbe ptr casa😁…te salut John!🤝
I’m halfway through, watched u take that gasket off with ease, I tried it and shredded it
Salut . Cu cîte ture reglezi la L si la H ????? Dacă se poate imi poți da un reper???? Mulțumesc.
I’ve got the same model, followed your strip down and rebuild, starts runs for a few seconds then cuts out any ideas why??.any help would be greatly appreciated,thank you 12:25
Could You tell me how set L and H screws?
I close them both and then I open each one a turn and then I start the chainsaw and if I have to adjust a little more on each one!
top video
Ващщее молодцом, только с озвучкой надо было, така же хрень предстоит
Is it possible to use the ms181 fuel and oil tanks on my ms180 so i can use the quick release caps on my ms180?
No.
Salut, care este surubul de aer?
Salut este H ptr “aer”
I had change carburetor on ms 250
Why is your primer bulb missing? You can start without it?
There is no primer bulb on the MS181.
@@ArdGeal oh, ok. so the 181C has the printer bulb.
Am la fel drujba Stihl și nu reușesc să te normal la relantiu se tureaza și se oprește o pornire grea și nu știu câte ture trebuie să dau la H,L , LA
I adjusted the Low speed screw to the highest rich idle, now i can't turn the idle down enough to stop the chain from spinning.
5:00 Spray: crc?
Don't forget to reconnect your fuel lines. :)
Yes, that's the tricky bit & it did'nt get shown.. what a shame.😬
Super fain. Ai reinviat monstrul de crengi..
Am tăiat 10 ani cu asa ceva de la crengi până la arbori de 80 cm 😈 te salut Ady, toate cele bune. Big 👍
Multumesc John, sunt bune drujbe ptr casa😁…te salut John!🤝
I’m halfway through, watched u take that gasket off with ease, I tried it and shredded it
Salut . Cu cîte ture reglezi la L si la H ????? Dacă se poate imi poți da un reper???? Mulțumesc.
I’ve got the same model, followed your strip down and rebuild, starts runs for a few seconds then cuts out any ideas why??.any help would be greatly appreciated,thank you 12:25
Could You tell me how set L and H screws?
I close them both and then I open each one a turn and then I start the chainsaw and if I have to adjust a little more on each one!
top video
Ващщее молодцом, только с озвучкой надо было, така же хрень предстоит
Is it possible to use the ms181 fuel and oil tanks on my ms180 so i can use the quick release caps on my ms180?
No.
Salut, care este surubul de aer?
Salut este H ptr “aer”
I had change carburetor on ms 250
Why is your primer bulb missing? You can start without it?
There is no primer bulb on the MS181.
@@ArdGeal oh, ok. so the 181C has the printer bulb.
Am la fel drujba Stihl și nu reușesc să te normal la relantiu se tureaza și se oprește o pornire grea și nu știu câte ture trebuie să dau la H,L , LA
I adjusted the Low speed screw to the highest rich idle, now i can't turn the idle down enough to stop the chain from spinning.
5:00 Spray: crc?