There is a ribbon connected with the display, This ribbon other side connected to the circuit board, Board has small lock, First unlock the ribbon lock then pull the ribbon, Thank you
Greetings from Argentina. I wanted to ask you if you can help me! I have the same microphone and now when I turn it on, on its display it has an indicator with the initials "AF" that measures how much signal is being transmitted while you speak or sing... Now when I turn it on, without speaking or singing directly, the "AF" signal that it marks on the display goes almost to the top, as if it were transmitting audio. and then when you actually start to sing or talk into the microphone, it picks up as usual but when it plays the audio it does it with a little bit of noise, like it's some kind of RF noise, bad signal. I already tried changing your capsule, changing cables, trying another receiving base, and obviously, the problem is the transmitter. Is it permanently damaged? Or what could be causing that? From already thank you very much for your time.
please check the microphone connection from the top of the mic, if you have another microphone just exchange the mic part from the top. if the same issue happen That may cause mother board issue, Thank you
@@StreetViewBD Yes, try another transmitter and the error disappears. Dear I promise my last query! And I won't bother anymore, I wanted to know if technically, at an electronic level this can happen. The microphone is used by a punk rock singer, heavy rock music style, which exerts a lot of vocal pressure on the microphone diaphragm and excitation in the transmission signal, there is a possibility that the transmitter gain was not well set and - 18 db (which is what the transmitter comes from the factory), is too sensitive for pickup and the transmitter received a signal excitation all the time, always forced to the top, to clip, and this, so to speak, fatigue this component " dynamics regulator" of the transmitter some kind of component, (I don't know how to name it) but type, pre-amplifier or component in charge of signal transmitter. So now when you turn it on, this signal modulator or transmitter component is damaged. Can this happen technically or electronically? what do you think that can happen?
Factory default sensitivity may be -18db, now you may change the sensitivity at -30db and receiver AF Out set to -6db or-12db, if its remains same, then i dont know what cause it is. Thank You
@@StreetViewBD Yes, I already tried to go down to -48 db on the transmitter and in the same way, it continues to be with the AF signal at the top on its Display. If I could realize that the problem is the transmitter, because I tried the receiver with another transmitter and everything works perfectly. I really don't know what it could be. But my biggest question is to know if these teams have repair for things like that.
@@lukep99Thanks for getting back to me! Did you buy the display yourself ? And can you please send the link to it. I have been to trying to find the LCD Display and can’t 😅
Awesome video! I had the exact same problem and just finished my repair! Thanks for posting!
you are welcome.
Hello, witch flatcables are beetween the boards? Witch size and mm. Do you know? Thx
I don't know, i did not measured, Thank You
Urgggg. I try repairing mine after it drop from on stage and I am scared to go this deep but I guess I have to
follow the video, then check the component connection, You can do it, Thank You
Great! From Russia with respect!
Thank You
Do you have to remove the fin in order to remove the display cover?
There is a ribbon connected with the display, This ribbon other side connected to the circuit board, Board has small lock, First unlock the ribbon lock then pull the ribbon, Thank you
Was the battery getting hotter nd i i open it will it void warrenty
Battery condition was normal. its only problem was not powering on issue,
Greetings from Argentina. I wanted to ask you if you can help me!
I have the same microphone and now when I turn it on, on its display it has an indicator with the initials "AF" that measures how much signal is being transmitted while you speak or sing...
Now when I turn it on, without speaking or singing directly, the "AF" signal that it marks on the display goes almost to the top, as if it were transmitting audio.
and then when you actually start to sing or talk into the microphone, it picks up as usual but when it plays the audio it does it with a little bit of noise, like it's some kind of RF noise, bad signal. I already tried changing your capsule, changing cables, trying another receiving base, and obviously, the problem is the transmitter. Is it permanently damaged? Or what could be causing that? From already thank you very much for your time.
please check the microphone connection from the top of the mic, if you have another microphone just exchange the mic part from the top. if the same issue happen That may cause mother board issue, Thank you
@@StreetViewBD Yes, try another transmitter and the error disappears.
Dear I promise my last query!
And I won't bother anymore, I wanted to know if technically, at an electronic level this can happen.
The microphone is used by a punk rock singer, heavy rock music style, which exerts a lot of vocal pressure on the microphone diaphragm and excitation in the transmission signal, there is a possibility that the transmitter gain was not well set and - 18 db (which is what the transmitter comes from the factory), is too sensitive for pickup and the transmitter received a signal excitation all the time, always forced to the top, to clip, and this, so to speak, fatigue this component " dynamics regulator" of the transmitter some kind of component, (I don't know how to name it) but type, pre-amplifier or component in charge of signal transmitter.
So now when you turn it on, this signal modulator or transmitter component is damaged.
Can this happen technically or electronically? what do you think that can happen?
Factory default sensitivity may be -18db, now you may change the sensitivity at -30db and receiver AF Out set to -6db or-12db, if its remains same, then i dont know what cause it is. Thank You
@@StreetViewBD Yes, I already tried to go down to -48 db on the transmitter and in the same way, it continues to be with the AF signal at the top on its Display. If I could realize that the problem is the transmitter, because I tried the receiver with another transmitter and everything works perfectly. I really don't know what it could be. But my biggest question is to know if these teams have repair for things like that.
what is the name of the component you exchanged
Inductor coil that i have replced, this coil was displace from this board, I jusl placed it and solder it again. thank you
Bhi apni shobaider reply den shobche poran video te dekhi reply den kina😂😂😂
Thanks for the comments
Hi, do you know why the mic don't show numbers and letters in the display, only show backligths
If device is powered on then display board may cause this issue.
Thanks
@@lukep99 Hi! We currently have a mic with that issue. What have you done to fix it ?
@@graceproductions7530 yes, i change the display
@@lukep99Thanks for getting back to me! Did you buy the display yourself ? And can you please send the link to it. I have been to trying to find the LCD Display and can’t 😅