How to Replace Front Wheel Bearing & Hub 2003-2007 Toyota Corolla
Vložit
- čas přidán 9. 04. 2023
- Buy Now!
New Wheel Bearing & Hub Kit from 1AAuto.com 1aau.to/ia/1ASHF00486
This video shows you how to install a front wheel bearing & hub on your 2003-2007 Toyota Corolla. Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision.
This process should be similar on the following vehicles:
2003 Toyota Corolla
2004 Toyota Corolla
2005 Toyota Corolla
2006 Toyota Corolla
2007 Toyota Corolla
2008 Toyota Corolla
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obeb/1AXAA00013
• Pry Bar 1aau.to/oP5/1AXAA00020
• 19mm Wrench 1aau.to/oSo/1AXAA00010
• 17mm Socket 1aau.to/objM/1AXAA00015
• 19mm Socket 1aau.to/oabo/1AXAA00043
• 21mm Socket 1aau.to/oabo/1AXAA00043
• 30mm 12-Point Socket 1aau.to/oaa/1AAST00002
• Press
• Pliers
• Snap Ring Pliers
• 1/2 Inch Impact Gun 1aau.to/oqV/1AXAA00252
• 3/8 Inch Impact Gun
• Torque Wrench 1aau.to/oaxA/1AXAA00044
• Gloves 1aau.to/oR5/1AXSS00048
• Safety Glasses 1aau.to/oKp/1AXAA00343
• Floor Jack 1aau.to/oXU/1AXAA00068
• Hammer 1aau.to/oRj/1AXAA00091
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Auta a dopravní prostředky
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Wow. This guy is a very good and thorough mechanic. Excellent lighting and focus. This is how a mechanical how-to video should be done. I'm an experienced amateur mechanic but I learned a few things like don't put anti seize on the lug studs.
Great instructions as always, thank you for the torque specs too! Watching these guides helps my peace of mind a ton before i start projects on my 200k corolla.
This video sooooo makes the case for just buying a quality loaded knuckle. I did both in my 04 vibe.
Just got quoted from the car shop, $1300 usd w 60k mile warrant for both driver + passenger...I jist saved over 900 bucks doin it on my own, I grabbed the pre assembled knuckles they had on the website! 1300 is wild
Thanks for the vid. After watching literally a hundred of these it was the first one to mention which side this type of bearing can go into the knuckle.
I realize it's an edited video but not showing how you remove the stuck race that is still on the hub is kind of misleading. That usually requires using torches, air chisel, and/or a bearing race puller. I get not showing how to deal with the rotted dust shield, the missing ball joint nut... etc because it's a video showing about the bearing but you should have touched on the stuck race. Especially on how to not damage the hub during removal. We've all been there! Other than that pretty good/informative video.
So a few things. Dont start nuts with an impact! Also go ahead and buy a whole new hub, bearing, and housing BEFORE putting a new hub and bearing in a old housing. Other than that very informative 👌 thanks 😊
Excellent demonstration. I wish you were my mechanic.
Reusing clips saves editing time. Nice job!
TRQ, has good parts for a good price. Add good tutorials to that list!! Thank you!
Very informative and satisfying to watch
Well made video and effort with attention to details. Showing whole procedure with good visual angle and explanation.
Looks like it is hard to find a 30mm 12 point impact socket. You can find a 30mm 6 point impact socket and you can find a 30 12 point standard socket.
lol I'm a idiot, this whole time I could have just taken the ball joint off with just one bolt instead of the three connecting to the control arm. Taking the ball joint last time was the hardest thing but after watching this I can see why I made it harder on myself.
One of the best video on this topic.. Thanks
I was safety squinting as you were removing the snap ring.
Well now that I see all the hard work that goes into just replacing the wheel bearings, I won't be surprised if I'm charged more than $75.
So, if the shop wants to charge up to 2 hours labor, allowing for rusty parts and broken snap rings... I should be fine with it. Got it.
Excellent job, good video thanks
very good explained and clear thanks
Thanks you are helping a lot
Thanks very good video for non mechanical person
It’s faster to take the ball joint with the knuckle. It’s only three bolts and you don’t have to worry about the cotter pin and nut
Thank you for the video.
Brilliant video, and great angles thanks. Is it the same for Toyota Corolla 2012 Diesel?
Great video,seems simple enough but still a bit of knowledge and work needed (subscribed). PS, do i buy a press or just drop the car off and let them do it.🤔
thanks so much It was a very clear and easy way ..
Do u have to do wheel alignment after this kind of job???? I always hear u do
Let me know
Great video, thank you!
Very helpful vid!
Worked great 👍
Nice video, good education
keep in mind you'll have to get an alignment done if removing the knuckle.
I like the trick of using a big high hat brake rotor. What year/make/model vehicle does that brake rotor come from?
Thanks for the video- should I get an alignment after doing this job?
+MedikPac We would suggest an alignment after this installation.
Is it okay to add extra grease to the new bearings? I know theyre pre-greased, but would it hurt to add more so it can last longer?
Pls i stay in Nigeria. This actually is my job too. But is it necessary to apply some grease inside the bearing before installing them in d spindle?
Imma just buy a preassembled new kit😬
Dam to replace a carolla bearing is harder than a replacing Bugatti engine
Thanks!!!
Wow i thought hub assymbly just bolted on. Cant believe tgey still used this design on something until 07
Why didn’t a grease seal be replaced on behind bearings and before axle joint installed
I have OTC 6575 wheel press kit do on the car much easier expensive to do but worth it
amizing
Can I just buy the hub and bearing already ensembled ?
+jdm fans!! Yes you can! Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
Thanks giys
Drove over an invisible pothole on the freeway going 70mph and one of the threads on the wheel hub bent and ended up breaking off after I tried changing the flat tire I got from it 😤😭
👌👌👍👍
The OTC hub grappler sells for around $600
What is the cost of the repair shop?
$75-125 an hour plus parts possibly
What’s the name of the game?
Pay less then the cost of the shop
If the repair cost $800
The tool plus the part cost $750
😆
Buy used knuckles or pay TRQ?
Probably cheaper to pay TRQ
what did you learn:
Type your responses below
👍
DO YOU NEED A NEW HUB?
Replace it better than repair it 😢
..