इंजन का काम कराने के बाद क्या सावधानी बरतनी चाहिए? | HOW TO BREAK IN YOUR REBUILT MOTORCYCLE ENGINE
Vložit
- čas přidán 8. 07. 2020
- If you spent lots of money and hours of hard work rebuilding the engine in your motorcycle, scooty or scooter the last thing you want to do is ruin all that hard work by failing to properly break in the motor. The steps to follow for breaking in a rebuilt engine once it's running again will vary slightly depending on the type of engine. For example, the steps for a high-performance street bike requiring high RPM for peak performance differ from a more sedate side-by-side that relies on lower RPM torque to get the job done.
Adding Conventional Motor Oil
Fill the motor with a conventional engine oil, not a synthetic. Synthetic and semi-synthetic oils are too slippery and slick, which prevents the new piston rings and cylinder bores from seating properly. During the first few minutes of running, the piston rings and the walls of the cylinders need a small amount of friction so they can wear fractionally, and so their surfaces can conform to one another to form an effective seal. It's this seal that gives an engine good compression, and it's that compression that really adds to the performance of your rebuilt engine.
Static Engine Run to Operating Temperature
The first time you restart the motor after a rebuild should be a static run. Wheel the machine outside or make sure you're in a well-ventilated space. Then, start the engine and bring it up to operating temperature while gently varying the throttle between idle and 50% open. Don't go over 50% throttle at this point. Once the engine has warmed up, give it a thorough inspection for any leaks; listen for any odd noises; and look for any other mechanical issues such as excessive vibrations. Shut off the engine and let it fully cool down.
20-Minute Active Engine Run
An engine break-in happens mostly during the first 20 minutes of running after the rebuild. If you have access to a dyno, strap the vehicle down and vary the load on the engine between idle and 70% throttle. Otherwise, take the vehicle for a short ride to put a load on the engine. Vary the throttle between idle and 70% to push it a little harder than you did in the static test. Find somewhere without any traffic where you can safely run the vehicle while varying your speed to break in the engine.
Assuming everything goes well and there are no mechanical issues, start varying the throttle between 50% to 80% to further increase the load on the engine. Next, run the vehicle as you would in normal operating conditions.
#EngineRebuilt #EngineOverhauling #Automobile
Join my channel and become a member : / @mechanicaltechhindi
The wait is finally over. I am here with CZcams's very first Automobile & Mechanical Engineering Channel in HINDI.
In this channel i will upload videos related to automobile and mechanical engineering topics such as engine, I C engine, Cars, Motorcycles, Production, HMT, Thermodynamics, FM, CAD/CAM etc.
So subscribe my channel and learn everyday
Follow me on twitter: ⤵
/ dashingdanish11
Add me on Facebook: ⤵
/ danish.ali.754
Follow channel on Instagram: ⤵ / mechanicaltechhindi
Contact me: ⤵
mechanicaltechhindi@gmail.com
सर आपकी इस विडियो को देखकर ऐसा लगता है कि अब हमारा ज्ञान और नोलेज बढ गया है और आप का धन्यवाद ओर आभार व्यक्त करता हूँ ऐसी महत्वपूर्ण जानकारी देने के लिए.........👍👍👍👍👍👍🙏🙏🙏🙏🙏🙏
❤❤❤❤
Thank You ! Respect Brother! God bless you!
Bhut achi jankari di apne bro.thank you.
Helpfully video sir ji
Thanks so much sir ji
Jai Hind Jai Bharat
Vande matram
Thanks for giving these information
Namaskar, brother Aapke explain Ka tarika bahut achchha hai. Isi Tarah se aap hame guide karate rahe.
Bhut achhi jankari dete h aap 👍👍👍
Very informative video sir❤️❤️❤️
Intni sahi jankar dhanywad
Most informative video boss 👌👌👌
Bahut dino se wait kr raha tha
Recently I subscribed your chenal Vary informative & nice presentation your each video's Thanks keep it up.
Sukanta , Silchar Assam
😊👍👍👍
Dhubri here
बहुत सही और बढ़िया
SIR,Thanks for information.GHAZIABAD
Very very thankful & helpful info about engine work, and then precaution its helpful info about rider
Thanks for the information mera v engine naya ban k aaya hai
Bhot bhot धन्यवद् 🙏
Sabse badi baat video me time waste nahi hua to the point baat ki 👍
VERY INFORMATIVE
Tq so much bhaiya ji
nice information ❤️
Nice information bhai 👍
thanks brother abhi kuch din bad engine ka kam hoga activa ka to achchi jankari di aapne thanks
Dost jai mata di bahot badhia vdo
Sir can you please tell me my 160cc apache 160 4v bike, can I use semi synthetic oil?
Thankyou bhaiya ❤️
Thankyou so much
1 min silence for those who run bike 70 + one second day 😂😂
🤣🤣
Yeah... I crossed 80+
Bhai. Mene to 90+ kar diya gadi me se awaj aa rahi he tej 😭😭
@@sarc769 activa 90 jata bhi hai 😂
😆😆😆
Bhai... Very useful information... Thanks so much bhai.. Keep it up
Sahi video banate ho Bhai
Thank you sir
Bhai app tyre k upar koi video kar do.mera aveger 160 street bs6 main eurogrip ka tyre mila hain, mujhe lagta hain ki mrf ka milna chaiye tha.
Thanks 👍
Cbz k liye kon sa lubricant acha hoga... half engine ka kaam hua hai avi usme
Good explanation
If I want to put a new priston and ring which should i must put for mat mojar four strock two wheeler
Sahi baat batate ho
Enjoin recording or servicing ke kya aunter hota hai ? Kya galti kare se enjoin reapair ki nobat aati hai ?
Thank you boss 👍
U r most welcome
You are right
BHAI HERO HONDA HUNK, HONDA UNICORN YE BIKES ME COMPANY 10W30 GRADE KA OIL RECOMMEND KARTI HAI AUR BREAK IN PERIOD ME BHI YEH OIL 10w30 USE HOTA HAI JO SEMI SINTHETIC HAI USME BLOCK PISTON KA WEAR AND TEAR HO JAATA HAI ACHHE SE , PLEASE EXPLAIN KARE
Thank you boss
Good job
A bat to shai he sir 👍 super nice sir
You are best
Sir
Mere machanic bol raha h
500km tak one singal person hi bike chlaye two person bhi nhi bike per
Pls sugest me
Cbz xtrem main piston dalwaya h
Sir training dete hain ky aap automobile ka so plz mention this.
Sir❤️Engine rebuild Kaye 500km Kaye bad Monaye 20w 50 fully synthetic motual engine oil dala hai but galti saye grade mistake hua hai to koi problem Hoga Kaya?
Nice channel
Very nice video
Starts from 5:40
Thanx
Thnx
Bhai ❤
Thanx
Very good
Sir cd delux me 25 no piston laga hai bore kar ke milage pe kya effect hoga
Thanks bro from nepal
Welcome
Nisha gurgain ko jante ho kya
Tik tok wali
Sir mene 10 days pehle Bajaj discover 150cc ka engine bnvaya he lekin agr bike 45+ jaye to engine bandh ho jata he agr forse speed 45 se thodi less ho to fir se running krne lagta he to iss problem ko kese solve krvau
Sir ji scootor ka half engine bananeki baad double load chalasakty hy ya nahi?
Thanks sir g
if i rebuild sport bike engine , can i use synthetic oil or mineral oil during testing
mineral oil after rebuild
Thanks you bhai
Welcome
Aap bataa saktey h ki old model passion plus ka top speed kitnaa tak hoga 90 ya 100 km/h.
Mera glamour (2012) kaa block kit change huwa 70000 km pe, mechanic ne change kar ke uspe valvoline 20W40 900 ml mileage Plus Mobil dala, uske baad unhone 20 din ke baad engine oil change karne ke liye bola, meyne 1 month ke baad change Kiya, 200 km chalane ke baad, aur Mobil dala Apollo 20w40
Kitana kharcha aaya block kit change karne par
@@dalendrasahu9345 total 5000
Thnx sir 🙏🏻
Welcome
@@MECHANICALTECHHINDI sir Activa engine ka kaam krwane p ,kitne life rh jatee h engine ki??
Good video
Thank Bhi ji
Sir can we carry two person after half engine work is done???
Bhai abhi splendor ke engine ka kaam kiya hai. Par uski firing me idle pe ek hissing(khach khach..) sound ata hai. Speed badhne par kam ho jata hai.
Mechanic bola jab engine free ho jayega to awaj apne aap band hoga.
Kya ye sahi hai ya koi problem hai?
Tq bhai Saab
Tq so Mach
thanks bhai
Thanks brother
Nice infor
Thank you so much ❤️
I have a question...
Meri gadi ke engine ka kam krane ke bad wo jordar barish me bhig gyi khade khade...
Koi nuksan to nhi pahuchega na engine ko...?
Plz reply bhaiya... 😔😭
Bhai mere Scoty ki sound pore change' hogaye h engin fixing ke baad .. please guide
Sir mene meri tvs phoenix 125 ka engine repair kraya tvs k service center se uske total all engine parts change hue jo ki 7000 k parts hue or 3000 unne labour charge liye kam hone k baad mene bike unke kehne pr 30 40 km ki speed chlaayi phir first service krayi or service k baad mene gaadi nrml chalayi 70 80 km tk lekin first service k baad bike k engine head pr rubber ki seal h uske aas pss se oil leak kr rha h toh m apse yehi puch rha hu ki mujhe service center m jkr ky krna chhhiye
Scooty ka engine banane ke bad double seat ka prayog kar sakte hain ya nahin
Motul Maine dalwaya sir shine main 10w30w kuch nushan hain kiya phir Hum kun sha oil dalwaye shine bike main
Maine engine ko boring karbayata abhi engine bahut garam ho raha hain kya ye problem hain ya pir bore kar ne ke baat naye main hota hain?
Thanks
Bai ji mere paas glamour bike 2016 model hai uska maine piston ka kaam krbana hai toh main piston krbane ke baad daily 15 kilometre jana aur 15 kilometre ana updown kr skta hai total 30 kilometre uodown 15 kilometre jana fir 8 hour rest bike ko fir 15 kilometre aana bapis Aise kr skta hun
Sir mera ntorq peh blockpiston ka kaam hua hai 2din pehele kya mein ushpe pillion ride kr sakta hu 500km k pehele??
Kya kia tumne? Yeh youtuber reply nahi karta
Engine ka kam Karvate Samay कौन-कौन se parts repair karane chahie aur kaun se Badal dene chahie
Enjan ka kam hone par 100 km jane par kitna brack dena chahie.. Plz reply
Tysm
Very good information
Please make a Video on Honda Unicorn 150 cc
Bhai mera half engine bana h pulsar 135 ls ka abbi 500 km me kitni ki speed me chalaau bike apni
How to know when to open half engine?
Ek bar scuty bor hone ke kitane din bad ya km bad bor ki jaroorat hogi?
We want part 2 of this video
Sir mere pass honda unicorn hai mera mechanic muzze bht time bajaj company ka oil dalne ko suggest karta hai...kya honda ki bike me bajaj ka oil dalna thik honga?
Koi bhi daal do
Sir hero passion pro bs6 ka i3s kese kaam karta he,,, please boliye
Brother tvs ntorq ka kaam krvaya ae ...
Mera marketing ka kaam ae to daily 70 kms + scooty chalti he hai to kya mai average speed 35--40 rakh k chala sakta hu ya nahi
Sir kitna mileage degi full engine karane ke baad mera trip meter kharab h
Thaks sir..good explaination
But i say u again and again that please make a video on contineus variable transmission(CVT) as use in scooty
Or
Why are not use in bike and if use in bike then what can facing effect.
Can you take double load in pillion seat after half engine rebuild
for all those wondering this question you can after 500 km you should maintain your speed below 50 so that your pump is tightened without excess stress, strain in engine and a servicing is needed to be made after 500km as they have to tighten some engine components after rebuild do change engine oil too. After its made nice your bike sounds like new and runs comfortably without any problem. Also its advised to change your chain socket around 15000 km interval and change your clutch plate around same time after half engine has been made i.e. depending on its wear out around km as 15000, 30000, 45000, 60000 and so on. I hade made my half engine around 40000 km and its good condition now running smoothly Bajaj Pulsar 150cc ...
bhai half engine ya full engine ke baad break-in karne ke baad kya phir se long rides pe jaya jaa sakta hai??? long rides matlab ladakh hogaya ya kahi aur...
@@Kyubatauuuuuu haan bhai par 1-2 servicing k baad will be better option kynki tab tak aapko basic understanding hojayega apke bike condition ki but do test the pickup of it in uphill ladakh k liye aur difficult route k liye..
@@BruceWayne-lm2or bhai nayi bike ka pickup kam reheta hai kya???
@@Kyubatauuuuuu yes until first servicing afterwards its ok else if you experience problem please check clutch plate..
Sir engine flex karna sahi hai ya galt ke
Bhai bike ka engine banne ke baad single sitting chalye yaa double chla sakte hai
bhai meri bike ka engine bore hua hai kya main double sit ride kr sakta hu..
Which Mobil is best for 125 cc bikes
motul and castrol is best
Sir mare pas cd100 (old model) bike hai
Sunday engin repair kiya tha
100num ka piston lagvaya tha (phle 75num ka tha) or other parts new fit kiye the, Night ko jb mai ghr ja rha tha to mane speed 40 pr rkhi thi or arround 5km door jane ke badd bike bnd ho gye tab kafi try kiya but bike start nhi hui, tb to ghr chla gya, or next morning jb bike start ki to first kick pr start ho gyi,
( Mujhe ye pushna hai k bike bnd kyu hui, speed bhi limit thi or distance bhi jyada nhi tha, mechanic ne bhi sb work shi se kiya tha)
plz tell 🙏