Video není dostupné.
Omlouváme se.
How to Replace a Rear Wheel Bearing - Volvo Amazon, P1800S, PV544 and P210 (Duett)
Vložit
- čas přidán 12. 08. 2024
- Wheel bearing noise? In this video we’ll show you how to easily replace the rear wheel bearing of your Volvo Amazon, P1800S, PV544 and P210 (Duett).
• SUBSCRIBE to our channel (for free!) •
/ @nordicarclassicvolvop...
• OUR WEBSHOP •
nordicar.com/en
• PARTS USED IN THIS VIDEO •
Wheel bearing set: 181217
nordicar.com/en/product/3387/...
Brake drum puller: 9991791
nordicar.com/en/product/2218/...
Castle nut: 153031
nordicar.com/en/product/117/c...
Key: 160553
nordicar.com/en/product/2299/...
Wheel nut ½ UNF: 87699
nordicar.com/en/product/755/w...
Hub cap: 670437
nordicar.com/en/product/2450/...
Drive shaft: 89679
nordicar.com/en/product/6922/...
• OTHER VIDEO'S •
• Setting the valve clea...
• FOLLOW US •
Instagram: / nordicarvolvoparts
Facebook: / nordicar.volvo.parts
Music: Silent Partner
The best video I have seen for this subject. A+
Thank you!!
@@NordicarClassicVolvoParts I did need to rent (free) a hammer puller to get first drum out as it was a bear in a cave. The hammer puller was 1,2 3 free.
Great and well-made video. The music is 100% annoying and not needed. But thank you for a great video.
The first tool you mention is a torque wrench. What needs to be torqued down? Thanks.
Great video / explanation on how to do this job.
Thank you!
Awesome information, very detailed, exact to the point.
Great video, thanks for sharing!!! 👍 👍 👍
Why aren’t you here in Los Angeles, California?!!!😩
Can I ask, if the driveshaft has too much play (in/out) would that cause engagement issues within the diff? I am having issues with the right driveshaft when reversing, juddering, whereas rear left is fine.
In the film, it was forgotten to soak the felting in the seal with oil. if you don't do that, the filtring will "burn" and become hard. Also missing some explanation about the amount of grease on the wheel bearing,Too much grease leads to heat build-up and increased friction, which reduces the lifespan of a ball bearing. Otherwise an indicatively good film.
Maý breakdrum is realy stuck, i think i've got it under 2000Nm of pressure it's not moving.
How is it done on a Volvo 145?
Very different than on for example the Amazon, impossible to explain here using words only... Maybe we will create a new video for the 145!
@@NordicarClassicVolvoParts I'd love to see just this! Oh, and the centre support bearing replacement and determining which size bearing.
Can you get air suspension for one of those
On the left wheel are no shims?
It may have just one thick shim. Final shimming done on the other side as shown here. If it happens that you are only going to replace the bearing on that side you may be lucky enough to just be able to set the correct play by using it. If it is less you will have to get a suitable set of shims to obtain the correct setting. If too big, add shims as needed. Generally you will replace both bearings so so listen to the advise here about the shims.
What am I missing here? If you use shims on only the right side, you say it should be .10mm. You have 3mm between your flange and bearing race. You added 3.1mm of shims. That comes to 6.1 total. But you said it should be .10mm. What don't I understand?
Cancel that question. Nordicar kindly answered my question via email.
Will it be the done the same way on an 1957 Volvo PV 444?
Yes!!
@@NordicarClassicVolvoParts Thank you very much for the answer.
@@southgarden1443 no problem at all! :)
Bearing is not properly packed with grease!
Perfect.