Samsung Washer Spins and Refills Over and Over!! DIY fix. WA45H7000AW
Vložit
- čas přidán 25. 08. 2024
- I finally solved how to fix issues with your Samsung washer when it spins, fills up with water, and repeats over and over, and also how to fix issues when your washer shakes over and over and stops running during the spin cycle, showing a UE or DC code.
Or, if you want to buy the suspension rods, they are available on Amazon at this link amzn.to/3S9abDg
Thank you for this excellent video! I followed your advice and used the zip ties to lock 2 1/2" pieces of cut garden hose around the springs and my washer works perfectly now. Prior to this, I was shopping for a new washer. In 30 minutes you helped me fix a problem at no cost other than some old hose and zip ties I had in my garage. You are awesome and thanks again for posting this!
is the fix still working now?
@@andrewb7104man I did it the other day, got two loads out of it and it's not working again. I'm gonna get someone to look at it but it's the same thing. I don't know if the hose slipped off, but I'm ready to set the fucker on fire. So to save my sanity I'm letting someone else fuck around with it.
This did the trick! We have been dealing with the shaking for like 6 months. I finally got serious about looking to fix it and came across this video! It was great and cheap to do. I did the take off the top method which was easier for me.
Which did you do? What was in the video or stretching the springs?
Thanks CW. This fix worked for me. After a SPIN, the cycle was going back to RINSE but it seems to got fixe after I used this fix. I just want to share that it is rather difficult to pull the coil rods out from the Top hence i fixed this from the bottom opening. Thanks again!
Thank you so much for this. It was a lot more involved than I thought getting the top off and all the things unplugged and reverse but it's running like butter now. I'm so impressed! Thanks again 😁
Thanks. I also provide mind and body self help tips on my website utah23.org/
Thanks for the Vid! I used the 2 1/2" garden hose with the zip ties and my washer is back in business...
This Yankee ingenuity worked great. Wife is happy again.
Took the rods/hangers out tightened up the existing rubber sleeves with zip ties, washer is working. Thank You.
Thank You! You’re smarter than the Samsung engineers! Worked for us! Was ready to set machine on fire- only 3 years ago old!
Fixed issue with my Samsung. Bolt was already tight. Purchased 1 feet piece of 1 inch inner diameter vinyl pipe. Cut four 2 inch pieces, spliced open vertically and wrapped around each spring and tied each with 3 wire ties. 1 inch inner diameter does not fully wrap around spring and small gap is left but don’t worry it fixed my problem and now washer does not wobble and completes the cycle again. Thank you for sharing your knowledge. 🙏🏽
Holy hell this actually worked. I have a different samsung but did the same steps in the video and its spinning normally again!! Hallelujah thank you so much! I was about to throw this away and get a new one because it just kept filling up with water over and over again every time it would get to spinning!
@lydiahanson5655 which model number Samsung do you have? Maybe I’m the same and can try what you did.
@@christalmorrison482Buy the rods is not worth to do this
I had exact same problem on my samsung WA52J8700, followed the first step-tightened the middle bolt in the tub-whoah, problem is solved!
Thank you!!!
Which way you turn the first bolt to get cover off?
finally got to the spinner nut, to get cover off its right on that screw, hard has hell, use a hammer to hit socket, the spinner nut under was broken for me so i replaced it with a M28 size on amazon i have a WA48H7400AW/A2 model, once i replaced nut, it did same crap gets to 4 mins on spin and i basically stop it, the clothers are not drenched, but it will add time and do a rinse. I hate to buy new rods again as the rods i bought were purchased cheap on amazon a few months back.
Thank you ! This worked
Samsung Washer WA5451ANW XAA 02
Used 2 ft. PVC Disposal Discharge Hose -Home Depot ($5.99 -5/2022)
Additionally, to stop too much side to side motion- Lodged commercial cleaning sponges between washer drum and metal body (front, both sides & back). There was thin, worn sponge already.in these areas.
Access- Moved machine 1.5 feet away from wall and propped machine back with a cinder block under the front-- to get 2 front springs
With machine standing regularly, Took off thin metal panel off machine back to reach in and get back springs while sitting on floor. Also stuffed sponges on both sides and at the back of the drum from this area.
Opened washer lid (as if washing clothes) and squeezed sponge under front lip between the front of the washer drum and metal front of the washer.
Thank you so much! Our Samsung washer was doing this and driving me crazy. We used your hose with zip ties suggestion and it's been smooth sailing ever since. Genius hack!
For model WA400PJHDWR/AA works great as well! Thank you so much for making this video to share. Cheers!
So thankful to have found your video! I had used every expletive in my vocabulary while waiting by my washer, only to have it be out of balance, bang around upon spinning and reset to fill again with water. Grrrr. I chose to work from the bottom and had no trouble reinforcing the springs with some old garden hose and zip ties. Thank you so much. Sometimes it's the little things in life that make you happy.
This worked great and the garden hose did the trick! Washing machine works fine again. Thanks for sharing!
This was the perfect fix! Samsung and the other manufacturers have upgraded the suspension rod springs which have a spring damper on them. This is a good fix . I cut 4 1/4” lengths of 5/8 hose sliced vertically and wrapped the spring with the length I cut and used three zip ties per rod. Works perfectly! Thank you for the advice! Wade
Thanks
Washer was having this issue and vibrating violently. After researching a bit, I came to the conclusion I needed to replace the suspension rods. After successfully doing so, my problem still persisted.
Then, I came across your video, and it was the first time anyone suggested a loose bolt under the agitator plate. Checked mine and found I could easily turn it with my fingers. After tightening it, my problem was resolved.
Wish I came about your video the first time, would have saved me a couple bucks. The rods were probably due to be replaced anyways. Thanks for your video! Saved me a lot of frustration.
I can't get the cover of the bolt off is there a trick to do that?
@@belmontsolar6202I can't either. I'm ready to set the fucker on fire.
THIS WORKED.....THANK YOU!!!....after months of great swearing oaths and referring to dieties not really known in the Northern hemisphere....and about to go trot line fishing with this wee beasty eyed beastie....I tried this....It worked fist time
Grrrreat work around.
Again many thanks!!
"May ya be Ina heaven tirty minutes afore da devil knows your a gone"
To be honest I don't know if this video helped or not. But I did everything you said to do. Then I found out my wife was only washing 20 face towels at a time. Imagine the machine balancing that load on a fast spin 😆.
Overall great video. (I cut up a $60 hose. And don't know for sure if there was ever a problem) 🤣🤣
Just wanted to add an updated comment! PLEASE PLEASE TRY THIS GUYS METHOD IF YOUR WASHING MACHINE HAS THE SAME ISSUE OR PROBLEM, LITERALLY SAVED ME SO MUCH MONEY, USED WATER HOSE AND $2 ZIP TIES!! THANK YOU, THANK YOU, WORKED WONDERS AND SHUT THE WIFE UP LOL
THANK A MILLION TIMES bro. I did fix this problem tonight. feeling so happy. thank you
Followed along and now it’s working. Thank you!!
Thanks for sharing this great knowledge with us. I'm proud of you brother. 👏
Any time! Glad I could help!
I did the garden hose trick with zip ties. 3 zip ties per spring. Was easy enough to do with the washer on its side without having take the top off. I was just able wash a decent size load including 4 beach towels, with no issues. This certainly would have caused problems before the fix. Thank you very much for sharing. I was happy to fix it w/o having to take the top off, or buy anything!
You the MVP! Worked like wonders on my WA456DRHDWR/AA. I bought 7/8 2ft rubber hose at Lowes #814334. Fixed in under 15 minutes, under $6 . Easier to use your first method by tilting machine and working under the machine! THANKS A MILLION!
I got the hose did you put two slices of hose on each spring or did you just split one piece for each?
@@LuisHernandez-vq2ff Did you fix it? did you use one slice for each spring? or two slices for each spring?
Well, I followed all the instructions using pieces of garden hose, but I am still getting the unbalanced clunking. i also made sure the center bolt was tight in the drum. I have ordered the 4 rods and will try those. Maybe my springs were just too far gone for the hose pieces to support. I appreciate the video which allowed me to figure out how to get the rods replaced. Thanks!
UPDATE. I got 4 new suspension rods and put them in and it spins like a dream now! The rods were about $72 for the four pack and it was another 5 bucks for some lithium grease that I placed on the surface of the plastic piece at the top of the spring and the place where the top of the rod sits in the washer frame. It made a slight squeaking noise during the first run, but that's was gone by the third load. No more knocking and rocking!! Thank you for showing how easy it was to remove and replace these rods.
I started dealing with this problem and tried all these things and had the same problem you did. Once I started thinking about it I ended up taking apart the white plastic yoke that’s cradled on the far end of the spring with the rod in the center. I noticed there was damaged rubber material inside of these jokes and starting to realize what this piece of hardware did. A couple of years ago I replace the damaged rubber with fuel line I altered to fit inside of the yolk But it’s only last about a year. I do feel the engineering department this company could’ve done a lot better on the dampening design with this shock absorbing system
Showing my husband this video tonight... Washer haz been doing this for 2 months, our power bill skyrocketed because of it
The 30 dollar amazon specials fixed mine(at least for now) instantly. After seen lots of stuff about the special grease, I was worried when these arrived, as the old ones were very sticky and shock absorber like. Much more than the new ones. But they work just fine. This machine is getting close to that magic part obsolete no replacement age. I'd pay $2000 dollars for a NIB 1960s or 70s American machine with mechanical controller. THOSE were built to last, and they did.
My wife and I were just discussing trying to find an old machine. So tired of these new computerized piece of junk . Had one for 6 months, and the motherboard went out. Now a few years later it's this issue. Wish they built things like that used to
I do appliance repair and I've been looking for a way to fix these rods. Some of the Samsung rods are almost $100 apiece. This looks like a great idea! Now, I do have to mention that the nut on his machine is nowhere near tight enough. They are either hammered on with a spanner wrench or an impact wrench. There is no way possible to even get it close to tight enough with channelocks.
Thanks for the tips brother i need to do this to mine , i was going to purchase a new one
No problem, glad I could help.
Great video... it worked. You saved me a lot of money. I was about to buy a new washer machine.
Thanks
Still working?
Here's my take on the situation. It's the logic programmed into the controller. Only it's not programmed for bad hanger rods not doing their dampening job. The controller thinks the load is off balance beyond it programmed tolerance. The machine is programmed to refill and agitate in order to rebalance the load without human intervention. And since the bad rods make just about every load give an off balance command, it keeps doing it again and again. Feel free to comment, correct, complain, etc.
Yes, I think you are right. Because mine works just perfect, other than this UE code happening. Then, it spins most of the water out, and you think it's done. And, POOF -- it restarts by adding more water and repeating the cycle.
Thank you for sharing your knowledge. This totally worked!
Stil working?
I got lucky and was just a loose nut I used a monkey wrench and a mallet to tighten it my washer is a lg but it was the same set up but it tightened to the right. Thank you for the video very helpful
Thank you mine is fixed. Bless you.
This was a huge help to me. I have the dc code that pops on everytime, and it adds extra water. Q: Is your Samsung supposed too retain water after your cycle is done?
Had the same problem,returned the piece of junk to Home Depot and got Maytag problem fixed
Ew Maytag, should’ve got a Speed Queen
Many of the new washers have gone to the 4 rod suspension. I just had a amana washer suspension rods go bad (shock absorbers). The amana had piece of rubber like material which dampens the up-down and back and fort movement of the drum. I tried a similar method of pipe insulation wrapped around the rod. It would help the up and action, but not the sideways action. Parts are extremely scarce right now, somes are months on back order. These units should have a balancing spring between upper tub and the suspension rod for more stability. I opted the get a new washer (which is hard to do with most units on back order.
I’m
$1.06 of hose and it worked...thanks for fix!
Easier fix for the springs is to just stretch them twice the normal height and put them back in, no garden hose or wire needed. Working like new.
Still working?
I have seen where some fix the top plastic piece in a way that keeps it from moving up and down too easily.
I really doubt it
I don't understand, you made them longer?
Awesome fricking fix!!!!!
I fixed my washer machine. Thank you so much
I have a similar problem. I will try it. Thank you.
This is exactly the video we needed.
I’m glad it helped. Check out my website. I’m a licensed mental health therapist and provide self-care tips. WWW.UTAH23.ORG
Haha, my washer is constantly knocking itself unconscious! And often knocking itself into last week, going around and round in the spin-rinse circles!! I will give this a shot and let you know how it goes.
Well, how did it go? Did you fix it? You never came back and updated everyone.
ah yes, apologies. I ended up buying four suspension rods and my son changed out the old ones for the new ones. Works a charm now@@PoeLemic
Thanks a a lot for this. Did this and fix worked like a champ. Thanks again
I did all the steps and still my washer drum rocks side to side when it spins and the UR or Ub codes pop up.. Any other ideas?
I have a model WA48H7400AW/A2 Samsung washer and toughening up the stabilizer rod springs fixed my problem. Used sections of garden hose with zip ties. I was getting UE, U8 occasionally and sometimes no code. But the machine would refill and drain over and over. Machine didn't shake like in this video. Make sure to wear some latex type gloves as those rods are very greasy. Thanks a bunch.
This worked also for my Samsung WA400PJHDWR/AA 01
Thanks so much!!! The 1st step worked for me.
Having trouble getting the agitator off, any suggestions?
Thank you so much for the well put together video. It worked great! one question; somehow I get everything back together, but now the water is no longer working???any idea what i May have done to possibly prevent the water from the machine??!? Gratitude sir
This happend to me ,too. The washing machine is not taking the water...I don't know how to fix it now...
When you laid down the washer the water valves wiring connection to the PCB might have gotten loose. It needs 120VAC from the pcb to open up the valve.
How do I loosen that first bolt seems like it won't come off
What if your stabilizer rods already have a rubber fitting around the spring? Tighten it up with wire, or a zip tie? Or cut it out and use the garden hose?
Anyone know how to remove the entire drum? I’ve seen videos for other Samsung washers, but not this model. You seem to be the most informative video so far. Found this AFTER I broke that but (didn’t know it was a left handed nut)
Check out this one. It might help czcams.com/video/gTXoKMHHpLs/video.html
@@23sapper czcams.com/video/VrRNLxbTDLc/video.html
This one was actually a little better. I think my drum is fused to the that motor. I gotta try a hammer or something to separate the two
After removing the plastic cover, the first bolt that you loosen, is released/removed by going clockwise correct? Then when bottom plate has been removed, the large nut is tightened counter clockwise as you mentioned. I’m having a very difficult time removing the first bolt. Please advise, thank you.
Been having this problem for months and this video helped me fix it in 15mins! Thanks
Much appreciated
Nice video exactly what’s happening with mine. Hey would you happen to know how to avoid the machine from filling with too much water when u only have a few items? I can’t seem to figure out how to make it stop wasting so much water.
What do you have the settings on?
Yes, I'm having that exact trouble now, so I'm gonna try your suggestions. I've not done any maintenance on it before, but I sure have on my Samsung dryer that I bought at the same time. However, the Samsung dryer is sure easy to work on, once you've taken it apart before and learned how everything connects. So, a question is: have you had to do any other maintenance on the Samsung washer of yours? I'd be curious as to what you've done. Thanks again for this video.
It works!!! Thank you so much easy to do when someone show you the path
Thank you for this fix. My springs already had a small black spacer on them but I added the hose anyways to tighten them up. Now the washer runs full spin cycle and doesn't stop and reset to since again. Thanks!!!
jfergmon I am little scare to do that.
Hey @derrickwith2rs I have a top load Samsung washer that reads the code DC on it. My washer will spin then refill, spin then refill, and keep doing that. What can I do to fix that?
Pump may be clogged. Check out this video czcams.com/video/oOnxbj-unfc/video.html
How do you get the cover off the bottom drum cover? Meaning, the cover above the large bolt. I have a small cap over the small nut but can't get it off.
Thanks for the video. Had me up in the middle of the night fixing this bc i needed my clothes for the am. Going to be a long day tomorrow. Lol 👍
I just replaced all my suspension rods, made sure the washer is level, recalibrated it, and made sure the bolt was tight. Still having the unbalanced load problem???
Is that a standard nut I can get from Lowes or is that a special order ? I removed that plate and the nut it corroded and split?
You are the man!
Howdo you turn off the out of balance code. Cant wash blankets without it throwing the cide. Takes all day long to run one bedspread bc of this issue. Miss the old days. Machine would just walk all over the place but it got the job done
Thank you 🙏 you save me money It works Grasias
And it worked thanks
You da man! This fix worked great. Thanks for the video
Just want to let everyone know there was a class action lawsuit for this in canada and usa. Mine is having the same problem and found the lawsuit. Some people were injured because during high rotation it came off the support and literally the machine casing popped out.
I read about that a few years ago, these machines can go crazy!
Nice tips!
Samsung WA48J7700A Washer - wrapped a thick vinyl pipe around the rods and tied them down with zip ties. It stiffened the suspension rods so much that instead of looping the rinse spin cycle, the washer vibrates madly to the point where I have to shut it off before it explodes. Not good.
For my washer sometimes it sounds like a diesel engine but sounds different
What size socket did you use to loosen the bolt?
Yes, been very nice if he would have said that and let us know.
@@PoeLemic 10
Different models but the buttons and cycles look the same Samsung WA45H7000AP/A2. The inside is huge and looks great but I don't see the point if the water only fills up only 1/4 of the tub on the Normal cycle. Is this normal? I can see clothes on top just standing there instead of being underneath the water getting washed. Do you know how to get the machine to fill up with water more than the half way point? Also I cant figure out how to calibrate it. Did you ever figure out how to calibrate yours?
Thanks mate
How the hose help to the springs? Springs looks nice to me, but I guess I will buy a new ones because I am scare to put the hose. But thanks
Thak you for you help
Great video! Fixed my issue. Thanks!
Hey buddy, did you cut off the hose spacers that were originally on there or did yours not come with any?
Sorry I can’t recall. Too many TBIs. I don’t remember cutting them off.
I have a 9E code. What does that mean? Thanks
Water leakage some where
@@23sapper thanks so much for replying . I’ll check but I see no water anywhere.
For the ones that tried this around the time this video was posted, how long did the fix work?
Yes, I am curious also. Guy above seemed to say that his dampeners were too far gone, so he replaced them -- after trying the fix. And, the replacement made it like brand new.
i believe hose clamps would do a better job than the wire
Damn, are you a genius. Yes, that's the right way to fix it. Also, guy above said that he bought 1 inch plastic pipe and cut it. Because garden hose is too small. So, I plan to buy bigger pipe and see if I can fix it that way. But, I love your suggestion. That so brilliant.
Great video in the middle of it but I can't get the cover of the bolt off is there a trick to do that?
I bought new rods that fixed a banging noise, but now i get the spin then UE notification and then it jumps time to fill with water again. I have not check if bolt was loose or not. Note when replacing rods, replace one at a time.
had a broken spinner nut, replaced it, but still goes to spin, i have to stop it at about 4 mins or it will add time and refill. I got a M28 size bolt on amazon. So now thinking of buying rods again grrr.
Anyone know what size bolt that is, i finally got the first nut off and it was discovered that the bolt under the plate is completely cracked
Really helpful
Is the first nut reverse thread also
My washer is brand new and has done the rinse and spinning twice
Thank you for the great video ! Helped me fix my piece of shit Samsung
Thanks
Or Ub for my washer
For the hose he wrapped around the rods, what's the diameter or size he used?
Just your standard garden hose
@@23sapperthank you
i try to remove the nut on mine with ratchet but never work under the washing machine it turn on same time ...i just replace shock but hard to spin again .... model wa456drhdsu
I did this and it only works for two months. I order the suspension rods and fix the problem..
I bought the rods and replaced them but it didn't help. Washer still says UB and shakes 😢
Update: I just watched another video that said you need to calibrate it by holding Delay and the Temp button. Now my washer spins without any issues 😅 I really feel dumb cause I've been messing with it for MONTHS with no solution. I hope this helps
PISSED ... This worked ... go for the springs first, but why don't springs last on ok use . 6 years? This was amazing and embarrassing. Perhaps my one spring died. WTF ... 6 years. Doesn't make sense. worked amazingly .. for now
All I did was turn the washer off then turn it back on and put it on a different cycle and it starting working like normal again