Is This 3D Printed Tool Wall The Next Gridfinity?
Vložit
- čas přidán 12. 06. 2024
- In this video I talk about my top honeycomb storage wall accessories. This video is brought to you by Squarespace. Head to squarespace.com/thenextlayer to save 10% off your first purchase of a website or domain using thenextlayer.
I finally got around to doing it...
I finally got around to re-doing my honeycomb wall - the 3D Printed tool wall workshop organization system that I talked about in a previous video.
In this video I'm going to share a bunch of my favorite 3d printed honeycomb wall accessories, why you should 3d print them and what to look out for.
Roll up your sleeves, clear off your walls and get ready to hide more filament from your spouse or roommate… it's another 3d printed organization episode!
💬 JOIN MY DISCORD: jle.vi/tnl-discord
🎁 EXCLUSIVE CONTENT ON PATREON: / thenextlayer
🎥 IN THIS VIDEO: 🎥
00:00 Introduction
01:01 Parametric Circular Device Mount
01:55 OpenSCAD Parameterized HSW
02:58 Countersunk to Hole
03:39 Honeycomb Wall Storage
04:12 100mm x 140mm Bin + Trays with Lips
04:45 HSW Squirt Bottle
05:20 Gridfinity HSW Base Plates
05:42 HSW Shelf Support
06:23 Cold Shoe Mounts for HSW
08:03 Proper SD Card Holder
08:34 Hook (50mm)
09:17 HSW Pins/Hooks
09:37 HSW Compliant Mechanism Clip Mount
10:07 MagSafe Puck Adapter for HSW
10:30 HSW Snips or Pliers Holder
10:56 Benchy Display for HSW
🛒 RECOMMENDED GEAR: 🛒
📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing
📍 Complete list of my videography gear: kit.co/jlevi/content-creation
📍 My favorite 3D printing filament: jle.vi/polymaker
📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted)
📍 My favorite BUDGET 3D printer right now: jle.vi/sovol
📍 Check out the official TNL merch: shop.thenextlayer.com/
📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links
🗳 STL FILES OF FEATURED 3D PRINTING MODELS: 🗳
🗿 Parametric Circular Device Mount: www.printables.com/model/3937...
🗿 OpenSCAD Parameterized Honeycomb Storage: www.printables.com/model/1632...
🗿 Some misc pieces for the Honeycomb Storage Wall www.printables.com/model/1626...
🗿 Honeycomb Storage Wall Alternate 4-Insert Wall Attachment: www.printables.com/model/3487...
🗿 hsw shelf by brett: www.printables.com/model/1580...
🗿 HSW bucket-shelf by brett: www.printables.com/model/1633...
🗿 100mm x 140mm bin: www.printables.com/model/4300...
🗿 Honeycomb Wall, ALL DESIGNS!!! : www.printables.com/model/3933...
🗿 Bottle Holders for Honeycomb Storage Wall: www.printables.com/model/3856...
🗿 Honeycomb Wall Cubicle Hooks: www.printables.com/model/3873...
🗿 Rotated Longer Command Strip holder for Honeycomb Wall: www.printables.com/model/4246...
🗿 Honeycomb Storage Wall Shelf Supports: www.printables.com/model/3619...
🗿 Cold Shoe Mounts for HoneyComb Wall: www.printables.com/model/3000...
🗿 Proper SD Card Holder for HSW: www.printables.com/model/4338...
🗿 Yet another Hook (50mm): www.printables.com/model/2471...
🗿 HSW Pins / Hooks: www.printables.com/model/3230...
🗿 Honeycomb Wall Compliant Mechanism Clip Mount: www.printables.com/model/3337...
🗿 Magsafe Puck Adapter for HCW Honeycomb Wall: www.printables.com/model/3391...
🗿 Honeycomb Wall snips or pliers holder DOUBLE!: www.printables.com/model/3648...
🗿 Benchy Display for Honeycomb Storage Wall: www.printables.com/model/3507...
🔗 OTHER LINKS 🔗
👉 My video about my top organization systems: • My TOP 3D Printed Orga...
👉 Check out the subreddit I created for Honeycomb Wall: / honeycombwall
❤️ LOVED THIS VIDEO? ❤️
▶️ Subscribe to the channel
▶️ Watch my other videos: / @thenextlayer
🔔 Turn on Notifications
🎁 Support me on Patreon: / thenextlayer
🛒 Use my affiliate links for your 3D printing or videography needs: kit.co/jlevi
💬Join My Discord: jle.vi/tnl-discord
✍️ Write a comment below!
👍🏿 Like this video
#3dprinting #3dprinted #3dprinter - Věda a technologie
Thanks for watching! If you liked the video, a "like" and a comment would be great... sharing it with friends would be AWESOME :)
Hi.
thanks for all your incredible content!
where do we find your designs? did I miss the links to your remixes, ideas, etc? printables?
OMG I had the honeycomb frame backwards as well! I am so glad I watched this video... now the system actually works!
YESSS that's what we're here for
This video was brought to you by Honeycombspace!
YES
I really love my HSW - once I saw the original video it was moved to the top of my print list once I got my 3d printer. I've since gotten it all mounted and it has been a great addition to my 3D print workspace. So keep these coming, I could always use more idea's of items to print for my HSW
Great to hear!
You admit to installing the wall wrong, but then do not cover wall installation at all?
It’s easy to install, just put it on your wall however you like: screwing it on, gluing, taping and hanging
I've been printing hexes for my wall for 2 weeks now, lol. Unfortunately(or maybe fortunately) I've already seen all these. Too bad I didn't wait a couple weeks before surfing the 600 models on my own. Love the hex system!
Lol nice thanks
It’s taking me about 2 hours per panel to print each panel in black ABS on a Bambu Lab P1S (sport mode). I feel like if I had the AMS I could have printed off a tall stack of them overnight by putting a layer of breakaway support material between each panel. Now I’m cranking out connectors and wall mounts (another 2 hours or so). Really looking forward to putting this up on the wall!
Some of the peices you are using on your HCW I designed! : )
Great stuff! I'll be adding lots of these to my printable collections.
Hey! lets go! The transitions look sooo much better and way smoother! Awesome job and thanks for taking my suggestion! The video was great! keep it up.
Thanks!
"[...] whenever and whenever you need them." *chef's kiss* ;)
Omg. I am building honeycomb walls for my 3d printer enclosure. Perfect timing
That's awesome!
I will definitely use this!!
I'm new to this world and your videos are great. Thanks!
Glad to hear it!
Thank you for making this, You do what I would be doing if I had more time in a day to find stuff like this. My printer will be running soon and thanks you too!
Nice, enjoy!
Ok this is kind of exactly what I need! I've been struggling with organizing my workspace, and with HSW and Gridfinity I think I may get this problem solved. Now it's just a matter of doing the actual printing!
Enjoy!!!
The "HSW for Bambu X1C or P1P - 4 Layer print" on Printables saved me a lot of time
Wait what?!?!?!
This video was great! Thank you so much!
Glad it was helpful!
When printing the hooks, I get around the challenging overhangs by turning the hood upside-down and using supports.
I just shared the honeycomb wall project with my coworkers a few weeks ago. It's great stuff!
...I also used it backwards are first 😆
easier to put on the connectors right ?
is it hard just for me not sure if my printer is off or its this way
5.40 whenever and whenever you need em 😂❤
so much info.. I'm going be busy for days
I am printing this.
this is sick! i'm going to try and mount my flat screen tv using gridfinity! hopefully it holds up and doesn't break my TV :3
Can you explain how to made border for any size ? Thanks a lot !
"pop in your gridfinity accessories, WHENever and WHENever you need them... Speaking of WHEREver you need them...". 😂
In the process of building a brand new printer room in the basement, so I'll definitely be planning on filling my walls with this system once the walls are built!
Lol yeah... oops :)
Great video! A gridfinity video would be cool as well
Check my first video :)
do the pegs snap into place and if so how easy is it to remove and rearrange the layout
Is PLA fine to use, or should I opt for some other filament like PETG?
Hi, does this hexes printble in resin?
Thx for all nice tips
More advertising in this video than content! Best payed 3d CZcamsr!
One sponsored spot? How is that a lot?
Vertical gridfinity? Awesome!
WORD!
I love this system! Considering it for my garage. Has anyjne used it to store power tools and batteries and such? Will it handle the weight and torque?
I’ve seen people store 1 kg spools of filament so you should be fine
Good video!
And I still didn't find time to start printing my own HSW 😅
Get on it :)
after some time, I finally started building my honeycomb storage wall. :) will document everything and make a video about it in Portuguese for Brazilian and other lusophonous makers.
Great video really enjoyed this one thanks!
On another note i am also from israel and was wondering where do u purchase your 3d printers from cause from what i have seen if you order 3d printers from a local supplier the price is usually 2x-3x
I get all my printers free as review units, but I can recommend Rav-Meimad
Making lemons out of lemonade is impressive.
It's not that hard, I do it too. Just take an empty lemon, cut out a little hole in the top, pour the lemonade in, and glue the top back on. Tastes way better than a store-bought lemon!
lol can't believe i didn't catch that
0:21 You need to teach me how to make Lemons out of Lemonade 🍋
LOL I didn't even catch that :)
I can't seem to find the countersunk to hole STL file?
I still haven't managed to print out HSW parts that manage to fit together. Done four panels so far and a handful of wall mounts, but the tolerances seem really tight, esp for the .6mm I prefer for printing large parts. What nozzle size do you use for yours?
Maybe it's backwards.
@@raimondolle5707 No, this is before even getting it on the wall. IE, the parts that you'd use to assemble it. With them going in the thicker front of the honeycomb.
does anyone hava a good HSW base to recommend to put on the side panel of a X1C?
Damn. I regret to have bought some of the IKEA Skadis plates. The HSW is much nicer and - most important - individualizable. Maybe in the next life. Great video!
Sell the skadis!
Perhaps you can do a video or two introducing OpenSCAD in further detail.
I did a CZcams short, check it out :)
my printer on can do 9x9 panel, how do i get one smaller
So which way are you supposed to mount the wall? Asking for a friend...
I thought I had it right, but now not sure. A. How do you verify you have the the right way? I believe the "catch" or tab on the grid is away from you, which hold the nibs or tabs on the inserts which also faces away from you. B. Do you have to use PETG? I just can't work with the stuff. But I think more flexible, soft filament is probably a lot better than PLA. That said, C. Any tips for getting the tolerance right? I am experimenting, but the first round, I can snap them in, but once locked, there is not getting them out without breaking everything. Once option may be a jig in a matching honeycomb pattern to act as a "bang ring". The "ring" or honeycomb of 1 to 4 openings a little bigger than the inserts goes under the upside-down grid. Then a jig (6 sided pipe just smaller than the back side of the insert) goes over the insert and you bang it with a hammer to knock it out. But ideally, we should be able to hold the thing while still on the wall and wiggle out the inserts.
Upload pics on our discord or on the reddit i made
I used PLA
@@thenextlayer Any issues with it in PLA now that you've been using it for a little while? I'm just starting to try to print it and it's my first experience with PETG and after 3 days of messing with settings and trying different things, I'm pretty much ready to throw in the towel when it comes to using that material in my setup.
just got into 3D printing. I found out about gridfinity today…and I’m in big big trouble
Was the cleanup of the inserts a real pain for you too or did I do something wrong?
I genuinely didn’t know ppl display benchys looks very very cool when ya have it looking like a rainbow but il carry on building to my marvel display 🤙
Doooo it!!
do you need 100 infill?
cant you print the 50mm hook on it's side, wont it still be strong like that?
Yeah but still will be overhang issues b/c of the way the hexagon is angled
How did you connect the 3x2 grids to each other?
3x2…?
@@thenextlayer The other file was a large panel that looked too big for my Sovol SV06, which only prints 220x220x225.
I'm having issues printing this honeycomb. The pieces just don't fit... and I'm not sure why. Seems like it could be the corners bulging just ever so slightly? But it's hard to tell. I think it might be some issue with my print settings... I'm using Creality Ender 3 neo with PLA plz, what would you guys suggest for the slicing settings?
Tune your extrusion. Check the Ellis guide. Also you might have it backwards
@@thenextlayer calibrated my e-steps a few days ago-- should be good there. Nozzle is very clean and everything comes out fine. The pdf simply gives like... 3 settings. (Something I'm starting to realize with this hobby is hardly anyone shares their printer settings xD would really help someone new understand all the variables better)
Though I did do a test print recently where I basically slowed everything down... It took 20 minutes to print a single hex attachment and about 7 to print 3 hexes worth of the hex lattice itself.
Additionally I decided to use zero infil in the attachment (as it's plenty strong without it) and I massively lowered layer heights around the curved edges- hoping to get more accurate prints for both.
Oh and I reversed the lattice upside down-- so it's printing from the thin side up. This allowed me to better assure the top layer was properly made with no issues as the thick part of the hex is the side the attachments go in.
It worked out! Though it is still very tough (if quite nearly impossible without damage parts ) to get them out again.
Settings of note beyond defaults for a Creality Ender 3 V2 neo were simply -- adjusted variable layer heights to be smaller around the curves (so like .15mm ) and it would go back up to .25 or .3 for the more basic vertical layers.
I lowered the temperature for the orca's slicer default on pla (cura sets it to 200, orca to 220, so I went to 210)
And set infill to zero -- the lattice I made with 4 walls, the attachment I made with 3
@@rocovailo2862 Im struggling with the same problem... i got tired and literally started using a lighter to instert everytihing
Damnit! I already organized my crap on the IKEA SKADIS system! Grrrrrr..
Also good!
@@thenextlayer I want to put a 5kg heavy monitor on it, so I think I have more trust in the wooden IKEA pegboards than 3-4 perimeters of PLA... not to mention, the SKADIS is a bit offset from the wall, so cable routing is easy
Anyone got some pro tips to mount this on a concrete wall in a basement?
Concrete anchors ;)
Hello!
I have a question about ventilation. I recently found out that even PLA can cause permanent damage to the lungs. And i have printed a little over a year on my desk beside my computer. So my goal is to get the fumes away from my desk, however i live in a one room compartment and i only have a big closet beside my bed, like you have on your wall. So my question is how do you tackle the fumes inside your closets on your wall?
Check out my "ultimate 3d printer enclosure" video, I did a whole thing on it. You can print a filter :)
What software do you use to model ?
If you mean the program at 8:16 it's Blender.
Blender for some things, mostly onshape for others
Next Gridfinity? It was around first... Gridfinity is the next Honeycomb Wall...
Y’all just reinventing pegboard.
How strong is this? Could it hold, say, a shovel on a hook? Those garage organizer things are stupid expensive, and sure, there's french cleats, but c'mon, hexagons!
Sequel to this please !
That's a good idea, maybe I will do it :)
PETG tip: If you can't git rid of stringing by tuning retraction settings, then it's printing too hot.
Respectfully, PETG doesn't have to be *that* stringy 😬
lol fair
Even a year ago when this video came out who the hell but this guy was still using full sized SD cards?
Zack has been real quiet since this dropped
Lol!!!
5:39 "whenever and whenever" lol I think you misread the script
I do that a lot lol
Take my $3
I'm going with multiboard. far more advanced design.
First, Gridfinity. Now, this. *Sigh*, there goes more filament…
They are even compatible. There are Gridfinity modules that slot into the honeycomb. The expansion of neat 42*42 squares is non-negotiable.
@@p_serdiuk I know. And I am only sad for my wallet.
@@granthollingsworth230 F
YUUUP... At least I have coupons for you to save on filament ;)
(They're in the Patreon exclusive member discounts)
You mean "is this tool wall the next Alexandre Chappel storage system". Gridfinity was a stolen idea which took the credit, and income from Alexandre Chappel who is the person who came up with the idea. It is quite disgusting to hear people praise Gridfinity and the hack Zach. I do like this new hex system, as it is really a cool idea, and does not seem to leverage someone else stolen intellectual property.
I bought and used the system of alex, but switched to gridfinity because open source is always better.
NO its NOT! I have spent the last week printing the convoluted system that is multiboard and I have never seen a more confusing system in all my life! There is ZERO organization and no way to for the novice to know what piece goes with what! It should be a simple matter of plugging into the wall board and then plugging into it with some adapter. There are multiple adapters with long names that dont go far enough to identify what they are for. I for one am throwing my hands up and going back to Gridfinity! Multiboard is what you get when there are ZERO standards, just like working with electronics. Just because you have a USB adapter, does not mean you can solder it onto any board because there are 50 different configurations and Multiboards is just like that and is a bloated disaster that is going to waste filament and leave you with pieces that make no sense what to do with them! Even if you know how to put a square peg in a square hole, it is not going to save you from this bloated mess of a system!
This isnt the multiboard system this is the honeycomb storage wall and although the multiboard system looks the same it is made by a different person
Oh dear, it seems that printing a tool wall might not be the best use of your 3D printer's time and resources. But fear not, my friend! There are plenty of ready-made tool walls out there, from Ikea to the humble pegboard, just waiting for you around the corner. If you're feeling creative and want to print some custom accessories to spice up your tool wall game, go for it! However, the tool wall itself is a bit of a head-scratcher. It takes forever to print and can end up costing way more than a pre-made board. Plus, going the factory-made route would be more eco-friendly. Hey, we all love 3D printing, but not everything needs to be printed! Let's reserve that special treatment for the truly worthy objects.
I actually did calculate it and this is significantly cheaper than Skadis and uses much less plastic.
@@thenextlayerThere's a world of products besides Ikea's. Did you know that the Skadis panel is made up of 99% wood fibers? Pretty cool, huh? And while we're on the topic of considering things from all angles, let's take a look at 3D printing. While it's an amazing technology, let's not forget that printing a tool wall requires a lot of energy (which, unfortunately, comes with a hefty dose of CO2 emissions), and it can take a while to complete. So perhaps we should be a bit selective about what we choose to 3D print - after all, not everything deserves a spot in the 3D printing hall of fame!"