I bought a 5ive T last saterday and have 0.0 experience working on gasoline engines and RC cars in general. Today I followed your instructions and managed to install a killswitch. It took me over three hours, but in the end it works beautifully and I didn't run into any problems. Thank you so much for taking the time to explain the procedure, you are a HERO!!!! Greetings from the Netherlands!🌷🌷🐄🐄
I put mine on similiar button on my Rugged remote and have it set to On/Off that way I have control to turn it on and off. But of course that leads to sometimes forgetting that and needing to hit it to enable the engine. =) And nice install I didn't go to that extent. I took top plastic cover off and needle nose pliers and a small flathead screw driver you can pop the wire off the coil.
Looks great Earl. Every day you post I get super excited that today is the day you will let that beautiful limitless come to my house. I'm chopping at the bit to own a car you built with basherqueen upgrades! That limitless will have an excellent life with plenty of pampering.
Very cool Earl! I’m sure it would be a good feature to have on the vehicle. Thanks for showing the entire installation procedure. Your always very helpful! 👍💯👊🙏
Nice clean install earl of the kill switch thanks for all the hard work you put in for everyone and love watching your content have a great day earl 😎👍👍
Earl that looked like quite a lengthy job , also extremely complicated and some how you still made it look pretty easy. I’ve never worked on a 2 stroke but from what I’ve seen in your videos I think 🤔 I’ll be sticking to electric ⚡️. But it was still an interesting video for sure even setting up the auxiliary channel on the spektrum radio. As always Earl much appreciated brother 🙏👍💯
Thanks for the video but it would have been nice for the whole video to be as bright as the end. it was hard to see what you was doing for the most part. I have one of these coming and ordered the kill switch and wanted to see how to get it installed.
Wzup Mr.Moorehead!!! I'm glad I don't own one of those gas or nitro. But you got it. Your rc's be so clean 👌.I don't mind learning tho..thanks for the video.
Learn something new every day. That's what I try to do. Love all the great tips you have Earl. 👏🔥💯👍 In my opinion it's better to learn from ppl that own the cars vs ppl that sell the cars. (As far as rc's. ) There are a lot of options for rc's and stock replacements are just that. If it fails once it will fail again eventually.
Great video, very informative. I've been lucky I guess, never has a 2 stroke runaway. I need to check into this, for my HPI Baja. A runaway would be terrible, I thought chasing down a nitro was bad. Good tip on the coil gap!! Keep up the great work!!
Excellent video Earl , I have one of these kill switches on order for my 5-T and this is a big help for when I install it. Thanks for making videos like this
Just for future reference. It is possible to removed and install the plugs on the coil without removing. A pair of small precision needle nose is invaluable. That way you don't need to mess with redoing the gap. From one shortcut lover to another. Nice install though. Now run that beast!!
l Have a DX5C should I pull the battery/program button out and plug that into the red male plug of the kill switch then take the female and plug it into on / off of the receiver?
Thank you Earl for this video but hey...Isn't the kill switch should kill the engine in case if you loose the signal or you runnin low voltage. I have the same remote and Dynamite killswitch installed on my 5T, did the exact setup as you show but it's only kills the engine from the remote. I'm like...Is that what's kill switch for?!?
No in the remote as all two stroke come with a fail safe to apply brakes if batteries low or goes out of range the kill is so if the throttle sticks you can cut the motor off yourself 🤷🏻♂️that why I felt there a waste 👍👍
@@earlmoorhead5555 Sorry for dumb question Earl so, In other word the runnin low voltage receiver automatically apply brakes while you run your rc and you only can killswith the engine from your remote to prevent runaway right?
Hey early. Does the killswitch led stay on if your transmitter turns off ? Mine stays on and can’t figure it out. Feel like a kill switch is pointless if it’s not gonna kill the motor if the transmitter loses frequency or glitches and turns off
Yes as it kills power to the receiver but in this case I was having a signal loss on one of the three wires so it would run away and I’d have to kill it myself a bad receiver causes this issue
I bought a 5ive T last saterday and have 0.0 experience working on gasoline engines and RC cars in general. Today I followed your instructions and managed to install a killswitch. It took me over three hours, but in the end it works beautifully and I didn't run into any problems. Thank you so much for taking the time to explain the procedure, you are a HERO!!!! Greetings from the Netherlands!🌷🌷🐄🐄
Appreciate it 🙏
I put mine on similiar button on my Rugged remote and have it set to On/Off that way I have control to turn it on and off. But of course that leads to sometimes forgetting that and needing to hit it to enable the engine. =) And nice install I didn't go to that extent. I took top plastic cover off and needle nose pliers and a small flathead screw driver you can pop the wire off the coil.
These large scale gas powered RC should come with a remote kill switch from the factory. Smart of you to install one. Runaways can get expensive.
Yes I agree 👍👍
Looks great Earl. Every day you post I get super excited that today is the day you will let that beautiful limitless come to my house. I'm chopping at the bit to own a car you built with basherqueen upgrades! That limitless will have an excellent life with plenty of pampering.
Another great video with expertise
Very cool Earl! I’m sure it would be a good feature to have on the vehicle. Thanks for showing the entire installation procedure. Your always very helpful! 👍💯👊🙏
U did an excellent job installing that kill switch 💯👍
Nice clean install earl of the kill switch thanks for all the hard work you put in for everyone and love watching your content have a great day earl 😎👍👍
I think all 2 stroke gas rigs should come stock with this safty kill!!!
Earl that looked like quite a lengthy job , also extremely complicated and some how you still made it look pretty easy. I’ve never worked on a 2 stroke but from what I’ve seen in your videos I think 🤔 I’ll be sticking to electric ⚡️. But it was still an interesting video for sure even setting up the auxiliary channel on the spektrum radio. As always Earl much appreciated brother 🙏👍💯
I Need one of them kill switches on my electric rig for when it goes out of range. Great video.
Wow, that was quite a chore to get that installed. Not sure why I expected it to be simpler.
Thanks for the video but it would have been nice for the whole video to be as bright as the end. it was hard to see what you was doing for the most part. I have one of these coming and ordered the kill switch and wanted to see how to get it installed.
Wzup Mr.Moorehead!!! I'm glad I don't own one of those gas or nitro. But you got it. Your rc's be so clean 👌.I don't mind learning tho..thanks for the video.
Learn something new every day. That's what I try to do. Love all the great tips you have Earl. 👏🔥💯👍 In my opinion it's better to learn from ppl that own the cars vs ppl that sell the cars. (As far as rc's. ) There are a lot of options for rc's and stock replacements are just that. If it fails once it will fail again eventually.
Love anything 2 Stroke. Ready to hear that thing scream.
Great video, very informative. I've been lucky I guess, never has a 2 stroke runaway. I need to check into this, for my HPI Baja. A runaway would be terrible, I thought chasing down a nitro was bad. Good tip on the coil gap!!
Keep up the great work!!
Mine would loose radio control for a couple of seconds and that truly is scary 😱🤷🏻♂️👍👍
Excellent video Earl , I have one of these kill switches on order for my 5-T and this is a big help for when I install it. Thanks for making videos like this
Thanks 🙏
That was quite the job I haven't had any problems with run aways with my 5ive T yet, but that would Suck. Very instructional videos ,thanks👍
Yes my 5t been good to worried as the same switch in both 😳
Great video Earl 👍💯👊
No more run aways 🙏 Gas/Nitro are out my realm but I do love too hear & smell them run
Just for future reference. It is possible to removed and install the plugs on the coil without removing. A pair of small precision needle nose is invaluable. That way you don't need to mess with redoing the gap. From one shortcut lover to another. Nice install though. Now run that beast!!
Yes as I referenced that I’m removing for the ease
@@earlmoorhead5555 ahh, didn't catch that. I thought you were referring to the engine, not the coil. Cheers bud!
👍
Earl, Thank you for making vids like these. There great for referencing too. Looking forward to seeing you 🔥 some ⛽ . GASGANG 💪 💯👍💯🙏
Very informative video Earl, looking forward to seeing it going for a rip💯👍🏻👍🏻👍🏻👊🏻
Great video Earl.
Informative, thanks for sharing. 👍
Wow nice job much better idea than what I was thinking on the switch thx for uploading the resulting fix and fixed it fast to no messin around lol 😂
Sweet controller tip! 👌
Cool video thanks for the info!!!!
Great video Love that Losi DBXL. Any update on the Hot Racing Arrma 3s Drive shafts
Just got my tires
There's my #notification! The last few videos I didn't get the notification right away. No idea why 🤷♂️
Notification squad 👍👑
l Have a DX5C should I pull the battery/program button out and plug that into the red male plug of the kill switch then take the female and plug it into on / off of the receiver?
Thank you Earl for this video but hey...Isn't the kill switch should kill the engine in case if you loose the signal or you runnin low voltage. I have the same remote and Dynamite killswitch installed on my 5T, did the exact setup as you show but it's only kills the engine from the remote. I'm like...Is that what's kill switch for?!?
No in the remote as all two stroke come with a fail safe to apply brakes if batteries low or goes out of range the kill is so if the throttle sticks you can cut the motor off yourself 🤷🏻♂️that why I felt there a waste 👍👍
@@earlmoorhead5555 Sorry for dumb question Earl so, In other word the runnin low voltage receiver automatically apply brakes while you run your rc and you only can killswith the engine from your remote to prevent runaway right?
Hey yooooo 🤙
I heard you can't use an avc reciever. Is that true?
Gas receiver supposed to be different 😳
Hey early. Does the killswitch led stay on if your transmitter turns off ? Mine stays on and can’t figure it out. Feel like a kill switch is pointless if it’s not gonna kill the motor if the transmitter loses frequency or glitches and turns off
The light should change colors
What voltage did you set on the kill switch it's self because you can set it for 4v 5v 6v I have set mine at 5v
6V because the servos need that as a minimum to work properly 👍👍
Hi, cool video 👍 Will it also kill the engine in case total battery loss/ disconnection of the battery ?
Yes as it kills power to the receiver but in this case I was having a signal loss on one of the three wires so it would run away and I’d have to kill it myself a bad receiver causes this issue
Who won the limitless
me
Did u really win the car
@@jessekormick3796 No. I wish though.
Lol. Me too buddy
😆 bs