SLOW DOWN FOR STEERING TUTORIAL | EDGETX | MT12 [EN]

#radiomaster #mt12 #tutorial How to setup your RadioMaster MT12 to get a slow down/delay on the steering channel? In this little tutorial I will walk you through every step.
If you would like to support me and my channel, then you may buy me a coffee:
www.buymeacoff...

[@mstein6164]

Great info for slowing servo travel. Exactly the video I needed

[@arminrc]

Thanks for watching! Glad the video was helpful to you!

[@rambo_flight__ken9791]

Another option without using logical switches is to utilize the curve function on the two mix lines. Use Curve => “Func x>0” for right turn and use “Func x “Diff”)

[@islandrc-duke1972]

awesome remote and information

[@arminrc]

Thank you!

[@georgiamountainoutdoors8538]

I think this may be what I'm looking for. My mt12 hasn't came in yet so I can't try it. Trying to learn as much as I can before it comes in. How slow can you make this?

[@arminrc]

Thanks for the comment. In the video I set a value of 1.0 for the "Slow up" / "Slow down" parameters. You can dial in values up to 25.0 which equates to about 12s (hand-timed) "delay" from Max to Min for example. Hope that helps.

[@andreaskassner3320]

Hey, servus und vielen Dank für dieses how to. Ich hatte es ja erst mal mit meiner QX7 nachvollzogen und es lief prima. Nun ist meine MT12 auch da und habe das und paar andere Dinge vom netten Joshua gleich eingestellt. Alles super, sogar wenn man in Richtung geradeaus einen slow down einstellt ist das so wie bei einer T4PV.
Habe einen R6FG und einen FS-BS6 angebunden. Beim R6FG kann man die Gyro-Empfindlichkeit über Kanal 8 mit einem Drehknopf einstellen und auch so gut wie aus bekommen, beim FS-BS6 geht gar nichts über einen der verbleibenden 14 Kanäle, da musste ich für ST und Thr auf Kanal 3 und 4 wechseln. Gibt es mittlerweile eine Methode das Gyro im FS-BS6 zu beeinflussen? Und wenn nicht gehn ma halt auf Kanal 3 und 4 da man ja sowieso auch noch Lüfter und Transponder ohne Signal anzuschließen hat.

[@arminrc]

Vielen Dank für den Kommentar! Ja, ist schade, dass es Im Moment nicht möglich zu sein scheint, den im FS-BS6 integrierten Gyro mit der MT12 zu kontrollieren. Wir sind hier quasi in der Situation, dass wir zwar die Syntax bzw das Protokoll kennen, mit dem sich Tx und Rx unterhalten, aber in Bezug auf den Gyro nicht wissen, was eine (original FlySky) Tx an den Rx sendet, um die div. Gyro-Parameter einzustellen. Da es sich ja um unterschiedliche Werte handelt, müssen es wohl auch unterschiedliche Datenwerte sein, die übermittelt werden. Ohne diese zu kennen, wird es schwierig, das nachzubilden. Problem ist hier natürlich auch, dass die Auswertung der Signale komplett intern im Rx erfolgt. Man kommt also auch nicht so richtig an die Daten ran, die übertragen werden. Man bräuchte einen Rx, welcher das entsprechende Protokoll (AFHDS2A) unterstützt und einen Art Data-Out-Port hat, der einem die empfangenen Daten herausloggt.

[@shawnchristopher9050]

How do you reverse the steering when I turn left it turn right I have tried everything I could

[@arminrc]

What do you mean with "everything"? What have you tested? If you really have tried "everything" than I can obviously not help you.

[@DanPRC]

Great videos of this radio. You’re doing setups that no one else has showed yet. Have you used this radio to control rc lights yet? I have mine bond to a DumboRc 10ch rx and I have most of the channels in use. Including the two shifting servos on my RGT Challenger. But I just can’t figure out how to turn the truck lights on and off. I have remote switches and lights in my channel 10 but no matter how I try to set it up I can’t get the radio to activate the lights.

[@arminrc]

Thanks for watching and taking the time to comment! Highly appreciated! Unfortunately I do not have an Rx from DumboRC. But may I ask you how you connected the LEDs to the Rx? As far as I can see, the X10F has a dedicated LED port. Do you use this port? How do you activate the LEDs with the original Tx from DumboRC?

[@arminrc]

Just ordered an X10F 😀

[@DanPRC]

@@arminrc That dedicated port is for always on with the M12 radio. The stock and DDF-350 radios allowed you to power on and off that port via the radios.

[@DanPRC]

@@arminrc I was able to use a remote relay switch from any channel with the stock and DDF-350 radios. This radio isn’t acknowledging the relay switch. I’m guessing that I’m overlooking a setting.

[@arminrc]

What kind of relay switch are you using? Can you tell me the exact name/type of it? The problem with this in the Rx "integrated" switches are, that the manufacturer can use any data word to trigger/toggle it. We are in the position, that we know the protocol which is used for the communication between Tx and Rx but we do not know what the Tx is telling the Rx to turn on/off the LED port. But with the external relay switch it should be different. The relay switch can only be triggered by the PWM signal the Rx delivers and this is independent from the used Tx.

[@jundelfintvhobby]

Sir I'm using mt12 and also beginner how can I add throttle trim in P1 dial?

[@arminrc]

Well, yes, you can do some sort of simulating a trim using the pots. But it is not that easy to explain, because you cannot use the pots as trims directly. You have to modify a global variable (G1 for example) through a special function by a software input mapped to the pot. Maybe it is the best if I make a video about it.

[@jesseharless24]

Could this be done with throttle? For drag racing?

[@arminrc]

Sure, why not? Simply apply the mixes to your throttle channel instead of the steering channel and modify the logical switch accordingly.