What a teacher, you try your best to explain everything details for us to be able to understand everything, may God bless you, because by so doing, you're putting food on some of us our family's table. Thanks alot.
Very helpful, made short work of this job, thank you! Also side note, my Vvdi mb wouldn’t communicate with this ecu on bench, autel connected right away with same setup
Good one there brother, I really enjoyed your teacher. Please i want to know more on benz programming. Thanks and God bless you more 🙏 for such a great job
Very good video, I have had magneti marelli 4HV which is not supported, I don't know what device can do it.. Ktag? have been forced to do Immo off, and secure the writing protection on eeprom after this, otherwise car would start only once. Customer was happy about that, old car. Situation becomes more complicated when dealing with OTP chips, or dodgy Motorolas MCU very fragile to the temperature. I didn't look In autel on this particular ecu, is also BDM method for cloning, using APA cables in case ECU is more damaged( some power transistors, etc) and is always chance to read straight from the chip.
Thank you for the video. I’m confused because you did a great introduction but I think you used only one ECM, and what I’ve seen was only one VIN number. You just saved and write the same information, you didn’t replace the ECM.
Well done homie So from my understanding the im 508 with gbox and Xp400 will perform them renewal of the me9.7 aswell. Question. Without old module communicating will the ultra pull the scn coding from autel servers to finish setting up the renewed module?
Sadly....i was thinking buy this device...it can work in immo key...just last one thing i want is the ECU... But thanx bro.... Mau you more succesfull..
Hello, I have a corrupt ecu due to wrong jumpstart… any advice on what to do please? I got a new ecu but file could not be transferred because some of the files are corrupt.
@@huyug1 The computer that is going to be programmed needs to be new or can be used. If you help me with that information, I would greatly appreciate it.
@@huyug1 thanks for the reply. I found out that what I wanted to do will not work unless I change out other components. It’s not worth the change. The difference changed to much between the two years.
What a teacher, you try your best to explain everything details for us to be able to understand everything, may God bless you, because by so doing, you're putting food on some of us our family's table. Thanks alot.
Great demonstration. 👍
Good job! Thank you for sharing. Much appreciated!
Very helpful, made short work of this job, thank you! Also side note, my Vvdi mb wouldn’t communicate with this ecu on bench, autel connected right away with same setup
I just did this with my IM508, it was the same process. Thank you.
Thanks for sharimg, i own 508s, but didnt know it can be do it, i use it only for key coding. Did younhave g-box or it is possible with out it?
@@darkojankovic6440 i belive you can do it without, but I did use g box
@@darkojankovic6440possible without. You must use a 120ohm resistor
Good one there brother, I really enjoyed your teacher. Please i want to know more on benz programming. Thanks and God bless you more 🙏 for such a great job
Thank you so much
This helped me so much
Great job 👍
17% charge on the unit...😮
Living on the edge!!
Very nice thank you for sharing
Very good video, I have had magneti marelli 4HV which is not supported, I don't know what device can do it.. Ktag? have been forced to do Immo off, and secure the writing protection on eeprom after this, otherwise car would start only once. Customer was happy about that, old car. Situation becomes more complicated when dealing with OTP chips, or dodgy Motorolas MCU very fragile to the temperature. I didn't look In autel on this particular ecu, is also BDM method for cloning, using APA cables in case ECU is more damaged( some power transistors, etc) and is always chance to read straight from the chip.
Hey Bro. Good job always. Do you mind doing online training and please where did you buy your autotel tool? Can you provide the link?
Awsome😊
Thank you for the video. I’m confused because you did a great introduction but I think you used only one ECM, and what I’ve seen was only one VIN number. You just saved and write the same information, you didn’t replace the ECM.
They were 2 different ECUs but I have already programmed that module before with same file that’s why it was same info in both modules.
Thanks
We have a latest Mercedes Benz it as a problem of ignition it was shock so can this affect computer box as well
Hi, thanks for the helpful video, do you deal with A271 mercedes ECU?
C180 petrol 2012
thanx
How would you go about with configuring the ecu with a new Eis … old one was lost
What can you do if you can't write even 1 byte because no room? Can scn rest that issue? What do you do?
Well done homie
So from my understanding the im 508 with gbox and Xp400 will perform them renewal of the me9.7 aswell.
Question. Without old module communicating will the ultra pull the scn coding from autel servers to finish setting up the renewed module?
I would like to know this as well did u found out.
where did you get the guide from?
Happy for your explanation, my question is can IM508 do this work.
Well yea same tool minus accessories and size.
Is procedure the same with CR3.XX type modules?
Were do you get the g box? Sorry, new to this and want to get a setupclike that.
Can you program 3.3 om651 ecu for a diesel Mercedes?
but what if i got the same ecu serie number as the old one do i need to do all this or i can just active the engine ecu ?
What a good system can I get this and at what price
Hello Sir,wierd question to you;could you only clone srs softa?
What if there’s ECU but no Eis or can’t read eis?
Hi.
It is possible to do the same thing with BCM?
Great vid....
Can this procedure work on swap ECU Jaguar s type year 2000?
No, unfortunately it’s a complete different system and it has different ways of doing it.
Sadly....i was thinking buy this device...it can work in immo key...just last one thing i want is the ECU...
But thanx bro....
Mau you more succesfull..
Please house……..how can I rewrite vin number in my GLK 2014 ecu
Hello, I have a corrupt ecu due to wrong jumpstart… any advice on what to do please? I got a new ecu but file could not be transferred because some of the files are corrupt.
Who can provide the website to purchase ECU upgrade program?
Does the maxsys autel ultra have bench programming options like the im608
No only im608 and im508
really great sir .
this can be done on Volkswagen Scirocco 2010 2.0 TSI ?
It depends on the type of ECU type. VW system is totally different and it has different way of programming
@@huyug1 Thank you
@@huyug1 The computer that is going to be programmed needs to be new or can be used. If you help me with that information, I would greatly appreciate it.
@@alexanderhenrriquez5563 it also depends on the ECU. But used one should be enough. If you tell me what type of ECU you have I can help more.
@@huyug1 how to contact you over gmail or Whatsapp?
Thanks for the instructions. How do I get in contact with you to get my ECU done so I can start my 1999 SLK230?
Can’t you just swap the EEPROMS? It worked on my ME 9.7.
what’s your price for this ?? thanks
How did you connect a mouse to the im608 tablet?
probably used a wireless mouse by putting the dongle in the other usb slot.
Where are you located?
How do we contact you for service?
Hi any better alternative to autel
Depends on what capabilities you are interested in
my autel im608 is saying cannot write new vin to unit. Do you know why?
Mine the same. did you fix it?
@@awnia961 had to buy another ecu, for it to write correctly.
You can. Certain functions are only available by OBD
Does im508 do cloning
Im608 and im608 doesn’t really do cloning but helps you to transfer immobilizer information
You didn't show us step by step
Hi how can I contact you? I need to program a vin number in a used ecm. I would like to send you my ecm. Email? Thanks
Dynamicautodiagnostic@gmail.com
Hii can you programme used Toyota ecu N4 on bench
@@huyug1 thanks for the reply. I found out that what I wanted to do will not work unless I change out other components. It’s not worth the change. The difference changed to much between the two years.
Where are you located?