Video není dostupné.
Omlouváme se.
Megasquirt MS2PNP Install - Turbo Hardbody Drift Truck Build
Vložit
- čas přidán 12. 09. 2021
- Part 1 of 2 of the Installation for the MS2PNP Megasquirt Stand-alone for the 90-95 Nissan D21/89-90? S13(w N76 connector)
This video will walk you through general information you need to know regarding the Megasquirt and some of its other connected components and will walk you through the install of the ECM, GM IAT sensor(and how to set up connector), EBC(Electronic Boost Controller), & the 54mm Trigger Wheel. Any questions feel free to ask in the comments!
Part 2 to come soon with a look into the tuning software and some of the changes needed to make all of the components I’ve either installed or removed, work! Also will show a more complete setup and some insight into what the near future and future episodes hold!
Also,
Officially announcing the change of the channel name to Street Terror Garage from EazyBuildz! Have already changed the TikTok but the YT and IG names will soon follow. Putting more effort into editing the videos and upgrading to some better equipment so hopefully you guys will stick around, the best is yet to come! Thank you for watching and also thank you for the support and feedback I’ve gotten thus far. The channel is slowly growing and I appreciate y’all for that!
#d21 #hardbody #minitruck #megasquirt #ka24e
![Electronic Boost Control: Wiring, Settings, and Results [Speeduino and Megasquirt]](/img/n.gif)
im having the hardest time getting mine to fire up
awesome bro! looking forward to seeing the ol' girl eat!
thanks man, very soon!
so the megasquirt is not a direct PNP to the stock ECU..you have to modify the wiring?
The connectors for the ecm are direct plug and play but there are added sensors for IAT and a few other small things that I added in with the MS to better run & monitor what I needed
My AFM is also wired into my ECM for failsafe precautions
The added sensors are not necessary but can be pretty vital depending on your setup. Since I was boosted, had blowoff valve, no IACV, no anything, I needed some extra sensors and monitoring abilities
Nice ! What injectors do you have ? I’m bout to turbo my hardbody I got the same intake n color combo lol I’m lookin forward to the rest of your videos keep it up you’ve helped me already with jus this one
I appreciate the feedback man, love to hear I could help out!! These are 440cc Top Feed AUS injectors to run it on low boost for a while
How do I know whether to run the 50 vs 54 mm trigger disk? The one your using is the 54 right?
Yeah, I’m almost 100% positive that i have the 54mm trigger wheel. Pretty sure I physically measured mine to be sure before ordering
@@StreetTerrorGarage bet I'll do the same then!
@@JapaneseMinitruck better safe than sorry man! Good luck with the MS 🤙🏼
@StreetTerrorGarage I just recently ordered the 54mm trigger wheel for my 95 nissan pickup truck and I ran into a similar issue I noticed you said it was kinda hard to get it in there, is it because there's 2 prongs that the wheel is suppose to line up with? Just curious how this setup worked for you
Hello I was wanting to fix my truck back and put power steering on it because it's a 1990 model and didn't have it from the factory but where it has a plantium from a 240sx the power steering hose hits the platium so what did you use to make yours work?
so all I did when I put the 240 plenum on is I removed the hardline on the power steering pump and rotated it almost 180 degrees so it runs next to the plenum instead of hitting it. it takes a little finagling but it will work just fine without it sitting in the bracket.
Is the line off of a 240sx or hardbody
@@JA-xv8qk the line I used is from the hardbody!
Do you disconnect the stock maf sensor and use megasquirt in its place?
yes, the Megasquirt uses an internal 3bar(I think) MAP sensor in place of the MAF. My MAF is completely removed
Will this ecu fit the frontier?Have a 2000 frontier with the ka24de.Trying to turbo.
no this in particular model will not but they may make one for your frontier! If it has the same Ecm plug as the 240sx KA24DE(unsure what years had de) I would assume they’ve done it or are compatible.
Ayyy dude!
wasssup man!!
Where can I find the mega squirt to buy
I purchased the Megasquirt and all it’s extra components from DIYAutoTune & AmpEFI. They make different plug & play computers for different year D21s.
www.diyautotune.com
What spark plugs are you running?
I’m running NGK BRK7ES-11
What type of maf do you run?
I had wired up both KA & Z32 MAFs with the SAFC but have now upgraded to MAP built into the Megasquirt
What intake manifold are you using?
It’s an Ka24e 240 intake manifold with an Xcessive Manufacturing upper plenum