How to Convert a Halogen Floodlight with 50W LED at home
Vložit
- čas přidán 5. 09. 2024
- How to convert halogen floodlight with led chip 50w that works on AC220 directly without power modeule,all electronics its on board.
I got mine 50w led cob chip from aliexpress:www.aliexpress...
I feel like the cable should include earth and that wire should be attached to the metal frame... if the live wire dettaches from the PCB (with heat and no clamps that's possible) you may end up with a lamp connected to the live wire...
I think the light will only turn on briefly and then die in less than 1 hour due to overheating because the heat is not distributed properly because epoxy glue is not a good heat distributor
What is the heat transfer coefficient of epoxy resin?
There's gotta be a problem with the heat release of heat.
Exactly
True, he could of used themal glue off ebay for like 3$
I Did The Same Thing with A Tractor Light & A Dollar Store Flash Light.. I Wanted A Vintage Looking Bullet Light And Got The Tractor Light for $8.99 and The Flash Light That Takes 4 Double A Batteries With The Silicone LED .. Anyway I Just Power It With An 18650 Battery (from A Dollar Store Power Bank.. I Left The Charger Complete and Just Soldered The Wires Into The Pos/Neg on The Battery.. So I Could Charge It With The USB.. I Carry A Couple More of Those Powerbanks in My Tool Kit).. It's A Motorized Chopper Bicycle With A 100cc Bike Engine on It That I Built Years Ago.. And Just Love It.. No Plates/Ins./Etc. .. Just 16 & A Helmet (where Helmet Laws Are Enforced).. And About 100 miles per Gallon.. and 2 stroke oil.. About 20:1 and They Go Pretty Good.. Mine Will Do Just Over 60mph.. Although, Some Places Treat Them with E-Bike Limits of 25mph..I Think?.. Close Anyway.. I Do That In Most Places Anyway... But, On An Open Stretch Of Back Road.. Let'er Rip!!! lol.
have you figured out a good way to reduce the decibel levels of the engine? I was considering using a gas-powered motor assist to bicycle, but don't want it to be so loud.
Excellent project 👏
The whole body of a floodlight is made of an aluminum -why not just mount led chip directly to it so it can be used as a heatsink?
That aluminum body is too thin to be used as an external heatsink and that LED Chip can get REALLY HOT that the aluminum body cannot dissipate and therefore, it would just be a blown LED lamp
I was thinking he would mount the Heatsink to the rear of the lamp. however, it looks like the lED chip was a bit too wide to mount flat to the rear of the aluminum lamp body. Although it looks like he could have shaved away portions of the LED board while preserving its electronics and then mount it to the rear of the lamp body with some thermal paste and the heatsink to the back of the lamp?
@@dhrubojyotighosh9592 Could still put the heatsink on the outside...
dislike for gluing the led chip heatsick with epoxy! the thermal paste had to be used and then fixed with 2 screws. it will burn soon.
oh noo thanks for the video.....waiting for your next video........big fan from sri lanka
How can you test 3v CR2025 Battery like a watch battery, can change it as well
this will blow up very quickly since you used epoxy instead of thermal paste so the heat transfer will be very bad plus there is no active cooling
Yes true, he could of put thermal paste in the middle, then used the epoxy on the sides to secure it down to the heatsink.
Very nice bro
Thanks
you have to be joking with that setup using glue as a heat sink paste or connecting to the heatsink?????? you must be crazy but you sanded the heat sink creating more air pockets i hope you dont EVER work on my fixes
Cool.
Bro ur mic is to sensitive
Pls fix it
The sound on this video is terrible. Makes it unwatchable.
Jak rozebrać klejony reflektor LED? How to dismantle a glued LED headlight?
Is that illumination worth 50 Watts?
Nice 👍
Where is ground wire?
👌👌👌👌👌
Buenicimo
That chip will die in a few weeks or months. Even a 10w led would overheat in there
I don't think epoxy is going to be very thermally conductive
👍
First
Just change the lamp
Охолодження мало! і нарешті ці модулі повне гівно вони працюють малий термін!
SMD LED chip is more eficcient
Que cambio
defend only 4 days 😂
I think the light will only turn on briefly and then die in less than 1 hour due to overheating because the heat is not distributed properly because epoxy glue is not a good heat distributor