Rest Carburetor back to Factory Settings like this….
Vložit
- čas přidán 29. 04. 2023
- Turning the fuel adjustment screws all the way in (clockwise) until they barely seat and then turning them out (anticlockwise) by a certain amount, usually one full turn, are common procedures for resetting a tiny two-stroke chainsaw carburetor to its factory settings. These factory settings serve as a starting point for further modifications. Here is a thorough, step-by-step instruction:
Tools and Materials You'll Need:
Small screwdriver or carburetor adjustment tool
Safety glasses and gloves
Owner's manual (if available)
Procedure:
Safety precautions: Before you start, make sure the spark plug is disconnected, the chainsaw is off, and you're wearing the proper protective gear, such as gloves and safety glasses.
Finding the Adjuster Screws: Locate the carburetor's fuel adjustment screws. These are normally found on the side of the carburetor body and are referred to as the "L" (low-speed) and "H" (high-speed) screws. For safety, they could have plastic coverings or caps.
Find Factory Settings: It's important to be aware of the factory settings that the chainsaw's maker suggests. These settings can differ based on the brand and model of the chainsaw, so consult your owner's handbook or the manufacturer's documentation to find out what they should be.
Initial Adjustment - Clockwise Seating: Begin by lightly seating or bottoming out the "L" and "H" screws by clockwise (inward) rotating each of them. When doing this, use caution to prevent harm to the screws or carburetor. The "closed" position is the default setting.
After lightly seating the screws, give each one a complete anticlockwise (outward) turn before backing off. For further fine-tuning, this one-turn anticlockwise adjustment serves as a starting point.
Put on your safety gear and start the chainsaw after reconnecting the spark plug. So that it reaches its operational temperature, give it some time to warm up.
Low-Speed Adjustment (L Screw): Slowly and incrementally crank the "L" screw anticlockwise (outward) while the chainsaw is operating. As you listen to the engine, keep an eye on the chain to see how it moves. The objective is to locate the point where the engine operates without hesitating or stalling. The ideal low-speed setting is indicated by this.
After making the necessary low-speed adjustments, run the engine to full throttle and slowly spin the "H" screw anticlockwise (outward) in tiny increments. The goal is to achieve error-free, fast functioning without too much smoke.
Final Check: After making these modifications, run the chainsaw for a few minutes at full speed and idle to make sure it maintains stability and doesn't stall. To fine-tune the settings, make any little tweaks that are required.
Verify with Factory Settings: Compare your adjustments to the factory settings if you have access to them in your owner's handbook. If there is a sizable difference, modify further as necessary to comply with the manufacturer's instructions.
Lock the Adjuster Screws: Once you're happy with the settings, you can mark the screw positions with a little bit of thread-locking compound or paint to prevent unintended change.
Remember that these are only general instructions for returning a two-stroke chainsaw carburetor to its original default settings. Consult the owner's manual for your chainsaw for exact factory settings. To guarantee optimum performance and safety, consult a qualified chainsaw mechanic if you have questions about carburetor adjustments.
I hope you have gained something from this video.
Thank you
Craig Kirkman (Owner and Creator of The Repair Specialist Channel)
#ChainsawMaintenance
#CarburetorAdjustments
#EngineTuning
#ChainsawRepair
#SmallEngineMaintenance
#ChainsawSafety
#CarburetorSettings
#FactorySettings
#ChainsawPerformance
#TwoStrokeEngine
#CarburetorTuning
#DIYChainsaw
#SmallEngineRepair
#CarburetorCalibration
#ChainsawCare
#EngineOptimization
#ChainsawTips
#ChainsawExpert
#ChainsawWorkshop
#DIYMechanic - Auta a dopravní prostředky
I’m a long time 2 stroke service tech, and I’ve had much better luck at just under 1-1/4 turns out from the seat position.
And very importantly, ALWAYS adjust the High Speed before the Low speed.
It will give you the smoothest transition from low to high speeds.
Excellent video. That's the best way to start an adjustment from zero.
oh, yeah
YT is an open source high school for DIY enthusiasts
thanks for sharing, bro'
This is my new go to channel for small engines! Thanks! Super helpful and easy to understand.
Your channel is THE place I go to for any help. It's like the standard videos for anyone interested in small engine repair. They probably play your videos at colleges.
How about the idle screw?
And he educated me again!!🫶🏼🫶🏼
This tips works on my stihl 038 & 381 too..👍👍
Thank you so much I have been looking for this information. 👍♥️🇺🇸
thanks you so much! i have a weedeater from my neighbors, and they said the engine was shot, turns it it just needed a tune !
Saya baru saja memperbaikinya... Dan telah berhasil bisa digunakan kembali beraktivitas
Brilliant
Straight to the POINT...Thank you
Thank you 👍
Good stuff
like this one. very clear advice
How come there's no heart instead of just a thumbs up. This literally just saved me my weed wacker. I was about to throw it out. 🙏
Thank you for that tip.
Thank You. I'm still learning
Thanks Craig, that's decent gen 👍
This is good for trying to “reset” a carb’s tune so you can get it to start and eventually tune it to run. Different carbs will have factory tunes set for the unit they’re attached to. That’s typically in the owners manual or a dealership workshop manual or something of the like. I work at an ECHO and Husqvarna dealership and we have carburetor adjustment manuals relative to the model and unit that tells us the factory settings for the carbs.
Obviously, if you don’t have the manual, this video shows you how you can work to get a random carb in tune.
Hi
thank you for sharing your expertise and insights regarding carburetor tuning and factory settings.
It's great to hear from someone with experience working at an ECHO and Husqvarna dealership, where you have access to detailed carburetor adjustment manuals specific to different models and units. These manuals are incredibly valuable for understanding the factory settings and recommended adjustments for optimal engine performance.
As you mentioned, resetting a carburetor's tune can be a useful step in troubleshooting starting issues and fine-tuning the engine's operation. The factory settings provided in manuals serve as a reliable baseline for ensuring the carburetor is properly adjusted according to the manufacturer's specifications.
For those looking to tune their carburetors, consulting the owner's manual or dealership workshop manual specific to their equipment is essential. This information helps ensure that adjustments are made correctly and in accordance with the engine's design and performance requirements.
Thank you for sharing your knowledge and emphasizing the importance of using accurate factory settings when adjusting carburetors. Your insights contribute to a better understanding of carburetor maintenance and tuning for improved engine performance.
If you have more tips or information to share, please feel free to do so. We appreciate your engagement and expertise within our community!
Best regards,
Craig
Great video.
I just want you to know that this is the exact video instruction I needed. Thank you, sir 🙏
You are very welcome thank you
Very helpful. thank you, sir.
You are welcome
That is great advice 👍
Thank you so much for your kind feedback. Craig 👍👍👍
Very good Explained 👍
Thank you for your kind feedback. Craig
THANKS FOR THE TIP HOPE IT WORKS
No problem. Thank you
Thanks
Thank you very much.
You are welcome!
Adjust as needed...just what he said
Thank you.
You're welcome!
i thought it is 1.5 turns, or it depends on maker of carburattor, or i am wrong?
There is nothing set in stone with this. It largely depends on the engineers preference of how the prefer to set them and of each individual manufacturers spec. You’ve only been told one way of doing it
I've always done it that way too... it works Everytime.. thanks for your opinion
Hi I’ve got a petrol leaf blower. And I adjusted the low speed needle and high speed needle. There is only one screw which operate the same needle eg low speed and high speed. I can’t seem to get it to rev up properly what the course of this problem
I'm at 2 turns out on the low speed and 2.75 turns out on the high speed. Maybe drilling my venturi out from 9.5 mm to 12mm had something to do with it?😅
I have a question. On my Pioneer 1200A, the throttle linkage is fine but the part on the carburetor won't move more than a millimeter. I disconnected the linkage going up to the carburetor and tried to move it with my fingers without success. I have never actually fired up this chainsaw. It was a gift and I just wanted to clean it up and that's when I noticed the issue. Any advice would be greatly appreciated. Thanks.
Good
I have an issue right now with my idle it seems to fluctuate and speed up, but when I push on the throttle it’ll correct itself. Than do the same thing after a few seconds. Any suggestions?
IS There Anyway I can Send A Picture Mine has the Same Screws But there's Plastic on both and I can Only turn it so Much I don't even know what its called
I hope the link I sent you works out for you!
Y si no prende maistro ?
I do two turns(then adjust H)
👍
Im a professional poor kid that grew up and could fix anything. I agree
👍
Well each carb have own factory settings for our RC cars engines is usually around 1.5 turns out
than you frindly
Will this work on a chainsaw
10,000 TIMES thank !
Some carbo have one screw
Uncle you're 💎💎💎💎
Thank you so much
@@TheRepairSpecialist welcome 🤗🤗
My favorite carbs
👍
Most saws are happy at 1.1/4
But i need throtle setting
Wht if it doesn’t start still
My chainsaw still bogs down not sure on how to put the screws exactly
Hi
This video of mine should help: czcams.com/video/74p9FLmIkkw/video.html
Thanks
Craig
Ingco trimms have on screw
هل هذا الوزن يصلح لمنشار ياباني
I have a Honda UMK-422, after changing carby still runs at max for 1-2 min then dies or stops, sounds starved of fuel, i checked the fuel cap breathes normally.. ? Would appreciate advice..
Check intank fuel filter/location
If these aren't set correctly,will the carburator leak gas?
HI
thank you for your question about two-stroke chainsaw carburetor adjustment and the possibility of gas leakage if the adjuster screws aren't set correctly.
In two-stroke chainsaw carburetors, improper adjustment of the carburetor screws can indeed lead to various issues, including potential gas leakage. Here's how this can happen:
Idle Speed Screw: If the idle speed screw is set too high, it can cause the engine to run excessively rich, leading to an overflow of fuel in the carburetor and potentially causing leakage.
Idle Mixture Screw: Incorrect adjustment of the idle mixture screw can result in a mixture that is too rich (too much fuel) or too lean (too little fuel). A rich mixture can lead to fuel overflow and leakage from the carburetor.
Float Valve or Needle Issues: If the float valve or needle is not functioning properly due to incorrect adjustment, wear, or damage, it can result in fuel not being properly regulated within the carburetor. This can lead to fuel overflow and leakage.
To prevent gas leakage and ensure proper operation of your two-stroke chainsaw carburetor, it's important to:
Refer to the manufacturer's specifications for the correct adjustment of idle speed and mixture screws.
Use the appropriate tools, such as a tachometer and a screwdriver, to make precise adjustments to the carburetor screws.
Regularly inspect the carburetor for signs of leakage, fuel overflow, or other issues and address any problems promptly.
If you suspect gas leakage from the carburetor due to incorrect adjustment, I recommend consulting a qualified technician or referring to the specific carburetor adjustment guidelines for your chainsaw model.
Thank you for your question and for engaging with our community. If you have further inquiries or need assistance, feel free to reach out!
Best regards,
Craig
I have been doing 1 and a quarter to 1 and a half. I've tried the 1 full turn and the machines don't want to start. Maybe at sea level 1 turn would do.
Same here 👍
Thank you so much it worked fist try
You're welcome! Thank you for your feedback. Craig 👍
Husky 395 for some unknown reason use 3 turns out.
Wow. Thanks for letting us know! Craig
I won't aviator air screw carbatour
❤❤❤❤😂
Does it work an a 29 still
Unfortunately this probably will not work for your 029 Stihl because as far as i can remember, these chainsaws don't actually have H and L screws. Don't quote me on this but I believe that, Instead, they have a compensator built into their design that alters Air/Fuel ratios automatically as they operate.
If you are having running problems due to the carb, then it might be a good idea to have the serviced and possibly diaphragms replaced. That might sort it.
Best regards,
Craig
L 1 1/2
H 1
Thank u man, u saved my a,s
You are welcome!
Wait, i thought the L was 1 and H 1 and a half?
Yes I agree with you, its just that some people recommend one turn, others on and a half, and then go from there, that's all.
Il faut qui sois de 1 en marche et de deux chaud
First count how many turns in.
Thanks
There is no one standard. Different engines and carbs are .. different.
Very true, but in general you can get away with setting most of them this way.
Thanks
Craig
@@TheRepairSpecialistFor my ms250 chainsaw to save fuel, H how many turns and L how many turns?
MOST CARBS OR MAGNETOS R CRAP.I GOT A BRIGGS TRACTOR CARB LEAKS HAD IT FIX TWICE N STILL LEAKED. THIS PARTICULAR MOWER SHOP SUCKS
Imagine Plastic around them both And u can only turn it half a turn on both ones White ones Red any ideas or should I Just Rip that Plastic b.s off
HI. You CAN certainly do something about this. Take a look at my other Short here in the link, which explains what I do in this situation. Please watch through he whole short because you need to get passed where I talk about the limiters function at the start: czcams.com/users/shortsG2Gw0rG-G_g
I hope it helps.
Craig
Dustin
Not working
What about the bottom screw and your video is great ty.
The bottom screw is the idling screw. It sets the idling RPM. Thanks. Craig 👍