50% Failure Rate! How To Install Crimp Connectors Like The Pros!
Vložit
- čas přidán 23. 08. 2024
- In This video I go over some of the biggest mistakes that DIYers don't know they are making when installing crimp connectors. I will then show how to fix these mistakes and how to properly install crimped terminal connectors!
🎉 Check out our channel memberships for some cool perks and to help support the channel! / @howtohomediy 🎉
🧰 Products In The Video 🧰
Klein Crimper: amzn.to/4dcOI5l
Klein Crimper With Wire Strippers: amzn.to/4ddhnav
Klein Regular Wire Strippers: amzn.to/42VwWye
Klein Ratcheting Crimper: amzn.to/48BeCwh
Large Terminal Connector Assortment Kit: amzn.to/3wctOCI
Smaller Terminal Connector Assortment Kit: amzn.to/3w0UwhL
Wago 221 Inline Connectors: amzn.to/3VS6Vyw
Other Recommended Electrical Tools:
Southwire Lineman Pliers: amzn.to/4b5UbcW
Klein Lineman Pliers: amzn.to/47MDfW6
Electrical Tool Belt: amzn.to/47GcbrK
Needle Nose Pliers: amzn.to/3vOTmFi
🎥 Related Electrical Videos 🎥
Biggest Mistakes Made While Wiring Light Switches: • The BIGGEST Mistakes D...
Biggest Mistakes Made When Wiring Electrical Outlets: • The BIGGEST Mistakes D...
Shocking New Way To Extend Short Wires: • "SHOCKING" New Way to ...
Check out and join our channel memberships for some cool perks and to help support the channel! / @howtohomediy
ALSO, here is our How To Home Amazon Store, where you can find many of the tools, items, and shirts I use and wear in my videos! amzn.to/3mcqu1E
My CZcams Filming and Editing Gear: amzn.to/3kqqkGl
Thank you for watching and for subscribing. You can support the channel at no cost to you by using one of the above affiliate links. This helps support the channel for new content!
Blessings,
Adam
How To Home assumes no liability for damage or injury. How To Home highly recommends using proper safety procedures and professionals when needed. Our content is for entertainment purposes only. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not How To Home. How To Home will not be held liable for any negligent or accidental damage or injury resulting from equipment, tools, electrical, fire, electronics or any items contained in this video. Attempt projects and repairs at your own risk.
I am curious, have you ever caught yourself making any of these mistakes? Some are actually quite common!
Yes, I think I’ve made every single one of these mistakes, I had no idea what the colours represented, and no idea there was a tool to actually crimp these properly other than pliers 😀 great video with lots of information 👍👍
As a teenager, didn't have good crimpers, would pull the insulated part off, use pliers to crimp, then heat shrink or tape the connector. I'd even solder them if I couldn't get a crimp tight enough.
I confess, I have had to use too large of crimp connector so I stripped extra insulation off, gave them a twist, then folded the wires over to double up the amount of wire for crimping. Probably not a good practice but seems to work ok.
Great video though, nice explanation on everything. 👍
Thats fine to do. Just as long as you dont cut wire to make it fit into a smaller connector.
I used to be electrician/technician and my hands looked just like yours with many small wounds. It's hard to do electrical work while wearing gloves. I do crimp connections just like you so to but I always put conductive grease on the wire before I crimp it. I prefer soldered connections if possible.
I hear ya. I finally found a pair of gloves thin enough for me to work with small parts. MaxiFlex makes a model called Elite, intended for workers doing electronics assembly. First pair of gloves this sweaty guy can wear all day without even thinking of taking them off.
👍Ratchet crimpers are the best, you can get different dies to crimp a variety of things.
Great video. I’m putting 14 gauge connectors onto speaker wire and I wasted about 4-6 of the connectors because I didn’t do extensive research beforehand (fortunately I purchased a 100 pack of both and I haven’t cut the wire at the reel side yet lol, I knew that was gonna end up coming in handy)
Great video, thanks for sharing. One of the few videos that bothers to point out that a terminal has a top and bottom…
Allowing backpressure of the big picture (the whole job) to interfere with somones attention to detail can cause all kinds of problems. Something as small as crimping can sabotage the install.
Proper tool for the job. Heard that for decades.
Good stuff. Thanks.
Love your videos. I've made some of the mistakes you've called out for sure.
Always something to learn, thanks
I do a bit of electronics and have that same Klein tool and another one from Vise Grip - that is an automated wire stripper. Several companies make them. IMO, if you find yourself stripping wire and making / adding connectors these are well worth the investment. It will make all your work better, cleaner and easier and you won't get so frustrated with yourself. All the cable cuts and crimps will turn out perfect every time.
Per industrial standards (IPC620) as well as most manufacturer's guidelines there should not be wire extending through the barrel towards the ring or fork as shown in the video. Wire should be flush with the barrel.
If you want reliable connections, you don’t use insulated auto style terminals. These are notoriously unreliable. If you want reliable connections, you use either open barrel terminals crimped with the proper tool that rolls the ears into the wire or closed barrel terminals crimped with a good tool such as as those made by DMC that do an 8 point crimp. Then after inspecting the crimp quality you apply shrink tubing for insulation.
I like to tin the wire. A little solder on the wire makes a sturdy area for the crimp to take hold.
Never, ever do this!!! Solder cold-flows under pressure, so it’ll be nice and tight initially, but will loosen over time.
@@tookitogo Maybe times have changed. That is what I was taught in High reliability soldering course back in the day.
@@RVH-io3dr I dunno. I’m a ridiculous nerd who has spent entirely unhealthy amounts of my free time gorging on connector information, and have actually looked at old military and NASA electronics training materials (going back to the 1940s at least), and I don’t ever recall having seen any recommendations to tin before crimping. Early materials (1950s) were still skeptical of crimping and treated it as borderline experimental; when they did start adopting it in the 60s, the requirements were already more or less the same as today’s. I do remember finding _some_ instruction in the old manuals that diametrically contradicted modern recommendations, but I don’t remember what it was. I’m pretty sure it wasn’t this exact issue, though.
What I can say with certainty is that today’s electronics technician training - I graduated in 2023 - and the current military and aerospace standards all concur that crimping onto solder-tinned wire is an absolute no-no. Same with screw terminals: tinning with solder is strictly prohibited. (It is OK with spring clamp terminals like WAGO, since the spring will automatically compensate for any cold flow.)
Awesome information as always! Thank you 😊
Great to know the difference in the crimp tool, I was using it on the wrong sided. Can always trust advice from scarred hands
Excellent video thanks!
Do you use the ratcheting klein tool for un-insulated connectors as well?
I was wondering if you or someone on here could recommend crimpers for insulated terminals and heat shrink terminals. Should I go with 2 sets of crimpers or get a set with interchangeable heads ? The heat shrink would be for utility trailer lights and the insulated would be for a low current application on the interior of a Boler rv trailer. Thanks for the video. I will be using it. Lol. I very seldom crimp and generally solder so I don't want to break the bank.
Great info thanks for sharing.
I solder wire into ring terminals and use heat shrink tubing, and it is superior to all other forms of compression crimping. I make battery systems with lithium cells and Solar equipment, and I can’t afford to make bad connections that even if they got wet they would not fail
I prefer non-insulated terminals. Crimp and solder, then use heat shrink tube with heat activated sealer. Obviously takes longer but lasts forever.
Those are 'Sta-Kon' type terminals... for eons 'Thomas & Betts' has been the premier name in crimpers.
I use a hydraulic press to crimp since 2020. The smallest diameter wire I can use is 12AWG. So I only use 12AWG wire and bigger for everything. I just make sure the wire has a high enough strand count.
I think the reason why the crimp produced at 9:45 by the cheaper tooth-and-slot crimping tool isn't as flattened as the crimp produced by the Klein crimping tool is that the slot of the cheaper tool is curved, while the slots of the Klein (shown at 12:43) are flat. With the cheaper tool, I would crimp twice... first using the slot area to start the crimp, and then using a flat area of the tool to complete the flattening.
You’re a genius
Wow. The stuff I didn’t know I didn’t know.
as a professional ag auto electrician^tm if it fits it ships, as long as she passes the tug test shes golden
I've seen comments from other channels where they said crimping isn't a good way of connecting wires. According to them they've seen many crimps fail. Every time I see those comments I wonder what tool was used to do the crimping and whether or not they had follow some other practices.
Even NASA likes crimping and they have specific procedures and practices to follow for correct crimping. It's the same thing with soldering. To do it correctly there are certain practices to follow for a good soldering job.
Just like anything if done correctly it is a great way of connecting wires in specific situations. No different than installing a wire nut or any other splicing device.
See ya!
A video on quality insulateed and non insulated connectors and butt plugs. Compare them to cheap amascam ones and the dangers of using them
good info
its also a good idea to not have a few snorts of scotch before crimping....
🤣 Fair point!
I really feel you should have shown the Klein have an alternate set of crimping teeth for the non-insulated terminals. Otherwise, this was a great beginners crimping video.
I showed both sets of teeth on it and explained them.
By heat gun insulator can remove and put in place after shrinking.
Super class I poor man I want a terminal crimping tool please sent
Great Video. Thank you for sharing. Have a nice weekend
What's with all the hand injuries? Wondering if I should be taking advice here..🤔
Some people question if they should take advice if my hands show no sign of injury since that is very common with it and now I have someone wondering if they can take the advice because I do have some minor cuts from working with it. I can't win! 🤣
Nec stats wire not to be twisted more than the natural lay of the wire.
I had to use a large crimp connector with a small wire in my car because I was going to ground and the ground screw was really large. What should I have done?
I'll say remove more insulation from the wire you are adding then fold the excess wire in a zig-zag pattern or roll it on to itself properly give you more wire for your crimper to crimp on and get a better wire crimping done with the small wire on to the larger crimp connector, that's the best way to make the most of what you have at hand the best.
You can buy terminals with huge rings or forks, but for small wire. You won’t find these at your local hardware store, but well-stocked mail-order electrical/electronics distributors (like Digi-Key) have them.
If your terminal is for somewhat larger wire (e.g. 2x the cross section), folding it back once is an accepted practice. (For example, 24ga in a 20ga terminal, or 20ga in a 16ga terminal.)
If you have to use a terminal for much larger wire than you are connecting, then get a short piece of the larger wire the terminal is designed for, and crimp it in with your thin wire. (For example, for a 24ga wire in an 8ga terminal, crimp a short stub of 8ga in with your 24ga.)
I just put wire in terminal slide off plastic cover. Solder wire to connector slide back on color cover. Crimp is unreliable solder isn’t
An improper solder joint is very unreliable. A cold solder joint is worse than a poorly crimped connection.
@@LTVoyager an experienced person does not do cold solder joint.
@@KE5ZZO An experienced person doesn’t do a bad crimp either.
@@LTVoyager hmmm let see auto manufacturers do not crimp battery cables. They are soldered because crimp come loose over time
@@KE5ZZO You better do your homework. This hasn’t been true for probably 40 years. Most lead terminals are swaged at the factory, which is essentially a crimp on steroids. Steel or copper terminals are crimped as is clearly stated in this AC Delco video that is 11 years old so crimping has been in use a long time in the auto world. Same in the aviation world. Crimps everywhere, no solder. czcams.com/video/PaBu7qywBIQ/video.htmlsi=b7HFI_ipv5rFYZeA
Hee hee hee hee...
You said butt
🤣
💙
0:01 most dyi people? Hahah trust me I was an electrician and a lot of those people wouldn't know that either.
Man, cover up that blood on your fingers. I can send you a couple bandages if you need!
Unrelated ~ but, Are there WAY more ADVERTISEMENTS than there used to be? Some even MUST watch til the end..😠
I dunno. That would be a question for CZcams.
None that you have shown is correct. First, dump that crimper and buy something decent, second, the copper is not supposed to stick out at the top, it's supposed to be level. And it's not any kind of vision, but standards from civilized countries.
Nothing you said was fact or correct. You are probably not from the US, which this video is more directed towards.
@@HowToHomeDIY The way the connectors are crimped is determined by international standards, not your ridiculous NEMA which is about 50 years behind.
@kikiv1993 thank you for confirming what I suspected. You don’t live here and don’t know our codes and procedures. You’re incorrect.
JESUS!! FRIGGIN ADS BRO!!!😕
If it's important, I crimp and solder!
If it is important, I use a good open or closed barrel terminal crimped with a good ratcheting crimp tool such as made by DMC.
@@LTVoyager 100% agree. I’ve given up on cheap crimp tools and terminals, and just buy name brand. I have managed to buy various crimp tools from TE, Molex, and DMC on auction sites (some used, many brand new) for a fraction of the original price.
@@tookitogo Yes, a good used DMC tool will work better and last longer than a brand new chinesium tool.
@@LTVoyager Yep. Heck, a worn-out DMC/Molex/Amphenol/TE/JST tool will perform better than a new chinesium one!