WTFOS & V01.07.0000 COMPATIBILITY Issue Fix | DJI Goggles V2 Gets Native Betaflight 4.4 HD OSD
Vložit
- čas přidán 2. 04. 2023
- The DJI Goggles V2 also supports the Betaflight 4.4 native HD OSD when paired with the O3 air unit. However, if you have WTFOS installed, there is a compatibility issue that causes the Canvas Mode menu option to disappear from the Display menu on the goggles. These instructions will resolve that. Thanks to K1200S08 for sharing these instructions with me!
=========================
Items suggested in this video
=========================
My Favorite Screwdrivers (Wiha Slotted & Phillips):
Amazon US: amzn.to/3tq15Eu
Amazon Canada: amzn.to/3E1Ph02
DJI Goggles 2 Integra:
Amazon US: amzn.to/40DmrND
Amazon Canada: amzn.to/3Kdzd0y
GetFPV: bit.ly/40IFvux
DJI FPV Goggle V2:
Amazon US: amzn.to/3H9FGZk
Amazon Canada: amzn.to/3VLHQlY
DJI O3 Air Unit:
Amazon US: amzn.to/3WZnupK
Amazon Canada: amzn.to/3jJszUR
GetFPV: bit.ly/3ioEE1s
DJI FPV Remote Controller 2:
Amazon US: amzn.to/3EPa8oJ
Amazon Canada: amzn.to/3XJRZ4w
XING2 1404 4600kv Motors:
Banggood: www.banggood.com/custlink/mG3...
GetFPV: bit.ly/3GQa7mz
iFlight 20x20mm F7 Flight Stack:
Banggood: www.banggood.com/custlink/3vK...
GetFPV: bit.ly/3vLrWx3
HQ T3x3x3 Props
Banggood: www.banggood.com/custlink/G3v...
GetFPV: bit.ly/3Zo04fR
TBS Crossfire Nano Receiver with Immortal T Antenna
GetFPV: bit.ly/3Zm2WK6
TBS Tango 2 Pro
GetFPV: bit.ly/3QsPlgj
SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack:
GetFPV: bit.ly/3kIHP50
XING2 1404 4600kv Motors:
Banggood: www.banggood.com/custlink/mG3...
GetFPV: bit.ly/3GQa7mz
Happymodel EP1 ELRS Receiver:
AliExpress: s.click.aliexpress.com/e/_DEH...
GetFPV: bit.ly/3GRtYC8
HQ T3x3x3 Props
Banggood: www.banggood.com/custlink/G3v...
GetFPV: bit.ly/3Zo04fR
=========================
Instructions & CLI Commands
=========================
Here are the steps you should follow to get both O3 OSD HD and WTFOS work (MUST do in the exact order):
- Boot the goggles into FPV System (DIY) mode and connect to FPVWTF configurator
- Remove WTFOS and reboot into O3 mode
- Connect to DJI Assistant (Consumer Drone series) and update firmware to 1.07.0000
- After update completed, swith back to FPV System (DIY) mode, reboot and connect to fpv.wtf configurator
- Run the CLI commands:
unrd slot_1.status_successful 0
unrd slot_1.status_active 0
unrd slot_2.status_active 1
reboot
- After the goggles rebooted, the configurator detected the slot problem and offered an automatic fix. Accept the fix.
- After automated fix applied, re-install WTFOS
- Reinstall packages (msp-osd, etc)
============================
Videos you may want to check out
============================
How to get your custom BetaFlight OSD working on the DJI O3 Air Unit | MSP Canvas Mode is HERE!
• How to get your custom...
You FINALLY Did It! | DJI Goggles 2 Native Betaflight 4.4 HD OSD Now Officially Supported
• You FINALLY Did It! | ...
FULLY Customizable HD OSD canvas mode for DJI FPV Goggles V1 & V2 | My EYES can't handle the BEAUTY!
• FULLY Customizable HD ...
Playlist: DJI O3 Digital FPV System | Reviews, Guides, & How Tos
• DJI O3 Digital FPV Sys...
#djifpv #fpv #drones
Mandatory Disclaimer: I participant in the Amazon Services LLC Associates Program, which is an affiliate advertising program designed to provide a means to earn fees by linking to Amazon.com and affiliated sites. Item suggestion links above are affiliate links and I will receive compensation if you choose to use them. There is no cost to you to use these links and any compensation received goes right back into the channel. - Věda a technologie
Thanks a lot my friend, finally works i my goggles v2 :)
Awesome, happy flying!
Great video. I have not had the issue but if I do I will know what to do. Thank You!
Thanks. Happy flying!
Спасибо! Отличное решение проблемы.
Welcome, happy flying!
Thank you! Worked perfectly!!!
Great! Happy flying!
thank u so much
I had .606 version with wtfos. After that I upgraded o3 side to 1.07 and saw that DYI side just auto upgraded to .607 and broke me wtfos. After that I just entered your cli commands and reinstalled wtfos. And now it’s working! 🎉
Awesome! Happy flying!
Puedes cambiar fácilmente a o3 ... No me aparece la opción en en menú..solo Dji FPV y avata
@@Thereivaj_FPV Did you upgrade the firmware when in both the Avata mode and in the DJI FPV mode?
New to dji.. using v2 goggles.. what mode exactly it " dyi "
@@jessefpv4949 I think DYI is mean DJI Digital System..
Great Video.
Thank you for your work. I don't have the O3 yet but I'm already on 1.07. I'll keep this video in mind.
Welcome. Happy flying!
fantastic man!!!!!
Thanks! Happy flying buddy!
Nice!!! Thanks
No problem, happy flying!
Thank you were much! I had this issue and was about to believe that the v2 goggles doesn't support hdosd at all even with the o3
Welcome. Happy Flying!
thank you so much! I still try to figure out if I should stick to my goggles v2 or if i keep my goggles 2. How is your plan as of right now? I am not sure because of fitment. And also insecure about range. Is the goggles 2 range with the old vistas and Airunits (using LHCP ANTENNAS) worse then with the v2 goggles because goggles 2 is using linear antennas stock? There is no really reliabale info out there and not even tests betwenn all the setups and antennas
I’ve had both for about 6 months now, let’s say I finally decided that I’ll be selling the v2. I use the goggles 2 with both the o3 and vista. The vista doesn’t work 100 percent with all the features but good enough. I haven’t noticed any signal differences in my kind of flying (usually within 500m and around buildings and trees). I like the portability of the goggles 2, the displays, built in diopters, and the fact that it can embed the osd elements on the video.
HI, i'm currently switching to the 03 unit is betaflight OSD supported natively for the v2 goggles? i've never installed the WTOF hack do i need to instal the hack before i switch over? i recently purchased a FC with a barometer and would find knowing my rough altitude to be useful with all the new laws coming in to place thanks for making these videos.
The O3 supports native MSP canvas mode. The WTFOS hack actually does not touch the O3 side of the software so it doesn't make any difference if you have it or not. If you want instructions on how to setup the MSP canvas mode, check out this video and make sure to read the pinned comment: czcams.com/video/KIis4hB_duQ/video.html
so this version is suitable with avata to right ?
Is there a newer step-by-step instruction video on how to take V-2 goggles that are normally used with Vistas, and update everything for 03 the air unit? Some older videos didn't have the newest firmware back then. And newer videos assume the user has already jumped through some of the hoops. Please reply with link.
Joshua Bardwell had a video a while ago. The steps are fairly straight forward. You just need to update the goggles in the Digital FPV System mode and then in the O3 Air Unit mode. I think it's this one: czcams.com/video/OuJhWgNnplo/video.html
Hey man, everything works fine as i follow ur tutorial but is there any chance we do not need to bind 03 everytime we change to DJI Fpv Mode/ Caddx vista?
No, it's been a bug in the firmware for a while now. When you switch modes, the bindings are lost on the O3 side. There's a feature on WTFOS that makes it so that the Vista bindings are retained but nothing can be done on the O3 side until DJI decides to fix this.
Hi, thank you for that video. So does this mean that after these steps I can switch between O3 mode and DIY mode at any time in Googles v2? And will all settings on both partitions be preserved, so they will not be affected and everything will work, including HD OSD in both modes as it should?
Not sure if I understand correctly. You were always able to switch between the DIY and O3 modes in the V2 goggles. You lose the bindings to the air units each time you switch though and have to rebind. With the new package from WTFOS, you don't lose the bindings on the DIY side but you still do on the O3 side.
@@Mangorille Well, expressing myself clearly in three sentences is not easy. So it's great that the bindings and DIY will remain, I have a lot more of those. So after switching to O3 mode you always have to rebind, not ideal but I can live with that. The O3 mode update will probably mess everything up again and it will have to be done again, I mean re-uploading WTFOS, packages and all settings...
@@MomoBrut Correct after switching to the O3 side, you will need to rebind the O3 every single time. Make sure you carry that small screwdriver / pin with you. If you keep your CLI commands handy, you can do the whole remove/reinstall of the WTFOS in ~15 minutes.
@@Mangorille If I remember correctly, it took more than 15 minutes, but that's okay. I have one more question this quad wit Vista? How did you get that 250 mW into the OSD? This is a power of what? VTX? Or?
@@MomoBrut With practice probably can bring that down. I had all my CLI commands in various video descriptions and was able to just copy-paste them over. The 250mw is the ELRS control link power.
Good morning,
I just ran this guide and thank you very much as you partially solved my problem (but I think yes of all .......).
I have Goggles v2 (with the same firmware as the video) and going from Avata to the Caddx video units of my self-built ones the bind remains on all drones (and here we have solved a big problem but not entirely ....) but if I then return to pilot Avata I have to bind again (here is the problem I have left but with the lesser evil)........ is there a possibility to keep the bind also on Avata?
Thanks Gerard
No, the loss of binding when you switch to anything O3 requires a firmware fix from DJI. Nothing we can do ourselves and DJI has not fixed yet. The WTFOS only touches the Digital FPV System (DIY) side.
@@Mangorille Thanks for the reply, we trust dji to fix this but I doubt they will fix it
@@gherardofaltracco1721 Probably their way of forcing everyone to convert all their drones to the O3.
hi Bro! thanks a lot for the tuto!
What happens to me is that when I activate the HD with O3, I lose some OSD legends, like GPS coordinates, speed, etc. But if I deactivate HD, I can see them. Any idea?
I don't use GPS so can't check on mine but are you sure that they're not just going off the canvas? What happens when you put them right in the middle?
My question is unrelated to this but I am seeing people with INAV and 03 air unit working. I haven't been able to do this. do you have any suggestions?
I don't use INAV, will wait for others to respond.
@mangorille I'm interested in that colored HD OSD stuff you showed in this video. I cannot find a video about it in your list of stuff, unless I missed it? can you link it? thanks for your time.
Hey. Here is the how-to video. czcams.com/video/A3MtAsy77zk/video.html
Hello, having the v2 goggles with wtfos and the o3 air unit, can you continue using the old air unit with wtfos without problems? Thanks for you video!
Yes you can. Make sure you follow this video so that you don't lose the HD OSD option on the O3 side.
@@Mangorille ok thanks !
Hey! Do the custom fonts work on the dji o3 ?
Hey. No, the only thing that works right now on the O3 is native MSP and HD OSD.
Hey I wanna use my V2 with the 03 rooted it but I haven't updated to the latest to support the 03 unit. Would I lose my root if I update ?
No, the root is a one time thing but you do need to make sure you follow the steps in this video otherwise you'll lose the HD OSD option on the O3 side.
Thank you a lot for this. It probably won’t fix my issue with battery voltage not showing.. not even in the dji Osd. I connected the wires correctly to my flightcontroller and even switching them out doesn’t make a difference. I am running betaflight 4.4.2 on my geprc cinelog 25.
Connected the white wire from my o3 to uart1 tx and the grey wire to the uart1 Rex on my fc. Msp is active. The betaflight canvas does not show and the dji voltage shows 0.00.
Before all of this everything worked with my vista and wtfo.
I am sure it will be figured out but it is extremely hard and complicated..
Kind regards,
Dennis
The voltage not showing is either a wiring issue, a ports setup issue, a software issue, or a physical issue with the O3. Go through each of these and see if any resolve your issue. I had this happen once on a brand new O3 and it took a software refresh to resolve it. I hope it's not a hardware issue, which can happen if the UART wires shorted on the O3.
@@Mangorille i refreshed the software and no luck. i then took another quad and hooked it up. in that quad i did get betaflight osd including voltage but not the voltage of dji osd. I then went back to the cinelog who has two uarts and i tried the other uart. nothing no osd at all nor working voltage. i am so sick of this that i will try and send it back... what a mess it is.
@@sprokkel30 That is very strange, if you get the voltage on the betaflight OSD, you should get the voltage on the DJI OSD as well as both come through the same connection.
@@Mangorille yes indeed and this works only on my f7 board with beteflight osd but not on my geprc f411 there I can’t even get the betaflight osd working. Maybe the o3 is faulty we will see :)
resolviste el problema?
@@sprokkel30
Thanks for this tutorial. I get no luck, unfortunately. I am stuck with "error 5-100-4" when attempting to update to v01.07.0000 at both Consumer Drone Series and DJI FPV Series. ☹
Are you using a Mac? Seems that like error has to do with a Mac. I found this video: czcams.com/video/yaMwygpEQh4/video.html
I ran into this error on PC as well. I do not have a Mac but I did upgrade to v01.07.0000 using the DJI Fly App without issue.
Thanks for the video. Unfortunately not working for me. Tried 3 times following your instructions step-by-step. Fresh V01.07.0000 HD OSD works perfectly for O3 air unit, but each time right after installing WTFOS, the HD canvas display mode gone. Don't know if WFTOS changed something or something I messed up.
Sounds like you're either missing a step or doing something in the wrong sequence. Did you run the CLI commands before clicking Attempt Fix in WTFOS?
@@Mangorille thanks sir. Yes, I did run the cli commands before attempt fix. Before install wtfos, I checked the HD cavas mode and it worked. But it disappear right after install WFTOS. Tried 3 times, no luck.
@@xiaobingyi5413 What version are you running on the Digital FPV system side of your goggles V2?
@@Mangorille version 606. I have a bunch of vistas.
@@xiaobingyi5413 That version looks good. Try reaching out in their discord. Looks like this fix does not work for you for some reason.
hello just started fpv i successfully rooted goggle v2 but i exit by error the "root mode" by cliking on go to dji fpv ui how can i go back? and by the way can i use wtfos with dji fpv?
Hey. Not sure what you mean. I'd suggest going to the WTFOS discord and posting some more details there for better assistance.
I don´t get it. My V2 is recognized but I can´t root, it just won´t do it. When I click on root, a window appears showing me the recognized Goggles, but once I click on connect, nothing happens. When I unplug the USB-C cable and plug it back in the steps are actually starting immediately, but after a few seconds it tells me that it failed after 10 retries. I can´t even get it rooted it seems. Running the V01.07.0000 firmware... Any idea? What is the FPV DIY mode? I only see the O3, FPV, Digital FPV System and Avata mode... No DIY mode.
Are you trying to use your V2 with an O3 or a Vista?
Does this update allow the goggles V2 to record the O3 OSD?
No, the V2 does not have enough horse power to overlay the osd on the video. This can only be done with the goggles 2 or goggles integra. Also, wtfos only works with the old generation air unit.
for the first time im ussing the wtfos I need to pay to connect the DJI goggles v2 and do the rest?
Pay? No everything is free. What step are you being asked to make a payment for?
@@Mangorille my goggles v2 are not conected to wftos, juts says this, Failed detecting ADB, please (re-)root your device!
I'm on mac
@@dronebirdun Can't speak to a Mac. Do you have a friend with a windows PC that you can try?
Can I install WTFOS in DJI GOGGLES V2 with Firmware V01.07.0000 even though I never had WTFOS installed using this procedure?
I need the most OSD recording in glasses.
What version do you have on the Digital FPV System side? You'd want 01.00.0606. I have a video on how to downgrade the firmware: czcams.com/video/A3MtAsy77zk/video.html
@@Mangorille My DJI GOGGGLES V2 goggles have firmware v01.07.0000.
@@JurajCs That's the firmware on the O3 side. What's the firmware on the Digital FPV System side?
On the O3 page is firmware V01.02.0000.
Hello I'm having trouble too everything is right and to the right firmware. No health check on wtfos using 03 unit. And I only see the basic stuff no beta osd.😅
Wtfos doesn’t apply to the o3. You’d want to follow the instructions to activate canvas mode (msp display).
czcams.com/video/KIis4hB_duQ/video.htmlsi=_CFaAqyMzICWkQy-
The wtfos is for the older vistas.. correct.. but the osd on the v2 I just can't get.. I also just now like right now updated the v2 and the unit 03... using 4.4.. in the release notes.. just plugged a battery in and just the basics osd.. idk I'm so confused
@@jessefpv4949 If you have the v2 and the o3, you need to follow the instructions to turn on Canvas mode. You can either follow the video I sent or look at the O3 air unit manual. Note that the instructions changed for 4.4. I have a pinned comment in the video I linked on what you need to do differently.
Who you record the osd?
You need a Goggles 2 or Goggles Integra. I used a Goggles 2 (there's a little note on the screen saying that it was captured using a Goggles 2).
Does it still work with the old AIR UNITS
The native Betaflight 4.4 HD OSD is only supported on the O3 side of the V2 so you will need the O3 air unit for this to work. You can continue using your old air unit with the DIY/WTFOS side and use the WTFOS to get HD OSD.
@@Mangorille Hi, After apply the above procedure, how can I enable the FCC mode and 1200mW with the old air units and vistas. Thanks in advance for your help.
@@2011Formosa No different than how you did it previously. Easiest is to just install that package on WTFOS. Otherwise you'd be using the naco textfile.
What is DYI mode? I can see only FPV mode - is this the same?
DJI FPV is the DJI FPV drone. If you go to the O3 mode, you'd want to select DJI Digital FPV System from Settings > About > Switch Aircraft Model
I cannot get osd dvr recording to working with my o3 and goggles v2. Is it because I have betafligth 4.3? This instructions is about OSD HD, and would be happy to have osd recorded at all...
Failed detecting ADB? what should I do?
Are you sure your goggles were successfully rooted? Do you have anything else open in the background that could be trying to access the goggles (such as the dji app or even the wtf webpage)?