Epic BLOOD-RED NZXT H9 Custom Loop Water-cooling PC!
Vložit
- čas přidán 5. 08. 2024
- 🔴🔴🔴 ATO-082 blood-cooled PC! What should be our next custom loop water cooling project?
Tiktok: / archetype_origins
Instagram: / archetype_origins
Facebook: / archetypeoriginspc
Shop our custom PC here: / shop
PC inquiries here: archetypeorigins.com/contact
Email: ben@archetypeorigns.com
Buy us a Coffee! ☕ www.buymeacoffee.com/Archetyp...
0:00 Intro
0:06 Building
2:22 Waterblock Installation
4:42 Fittings Installation
5:30 Pipe Bending
7:13 Filling Coolant
8:03 End Result
Specs on Amazon:
------------------------------------------------------------------------------------------------
GPU: Zotac RTX 4080 Trinity OC amzn.to/3obM6QG
CPU: Ryzen 9 7900x amzn.to/3OpCLPG
Case: NZXT H9 Flow amzn.to/3OlNNFK
MOBO: ASUS ROG Strix X670-E Gaming Wifi amzn.to/43b4SX1
RAM: 64GB Corsair Dominator DDR5 5200MHz amzn.to/42SwKPV
SSD: 1TB m.2 amzn.to/43b50FZ
Fans: 6X Lian Li SL-Infinity amzn.to/3pUMMKz
PSU: Corsair 1000w 80+ Gold amzn.to/42Ng9gq
Motherboard Cables: Lian Li Strimer V2 24Pin amzn.to/3ofBOPh
GPU Cables: Lian Li Strimer V2 PW168-8P amzn.to/3ohtGhj
LCD Screen: 7” LCD Display amzn.to/42QKVoR
Vertical GPU Mount: EZDIY-FAB Vertical PCIe4.0 GPU Mount Bracket amzn.to/3Itv6w6
------------------------------------------------------------------------------------------------
Custom Loop Water-Cooling Components:
GPU Waterblock: EKWB EK-Quantum Vector AMP amzn.to/3STnsRJ
CPU Waterblock: EKWB EK-Quantum Velocity AM5 amzn.to/3MVpsFm
Pump Reservoir Combo: EKWB EK-Quantum Kinetic FLT240 D5 PWM: amzn.to/3rhIv4S
Coolant: EKWB CryoFuel Blood-red amzn.to/41T6hQQ
Radiator: 2X Corsair Hydro X 360mm amzn.to/41VqEwZ
Hardline Tubing: amzn.to/3obnxDt
Flow Meter: amzn.to/3MjFqb2
Fittings: EKWB EK-Quantum Torque HDC-14 amzn.to/41Tqk1C
Offset fittings: EKWB EK-Quantum Torque Offset Adapter amzn.to/41P8pJv
Fittings: EKWB EK-Quantum Torque Rotary 90-Degree amzn.to/3sZuaLf
Drain Valve: EK-Quantum Torque Drain Valve: amzn.to/49RzMYy
------------------------------------------------------------------------------------------------
Accessories:
Rigid Tubing Finishing Bit: amzn.to/43cHEzW
Pipe Cutter: amzn.to/3MmbKtT
Leak Pressure Tester: amzn.to/45jcg4m
Bending Tool: amzn.to/3XDjD1v
Heat Gun: amzn.to/3YRnkSt
------------------------------------------------------------------------------------------------
#custompc #pcgaming #pcbuild #gamingpc #gaming #pc #gamer #pcgamer #pcmasterrace #gamingsetup #pcsetup #pcmr #pcbuilds #custompcbuild #battlestation #rgb #pcmodding #pcgamingsetup #pcmods #computer #amd #setup #nvidia #intel #tech #dreamsetup #rtx #gamingsetups #gamingrig #pcgamers #custompc #pcgaming #pcbuild #gamingpc #gaming #pc #gamer #pcgamer #pcmasterrace #gamingsetup #pcsetup #pcmr #pcbuilds #custompcbuild #battlestation #rgb #pcmodding #pcgamingsetup #pcmods #computer #amd #setup #nvidia #intel #dreamsetup #rtx #gamingsetups #gamingrig #pcgamers #reels #fy #fyp #shorts #youtube #unboxing #smallbusiness #businessowner #rtx #rtx4080 #rtx4090 #rtx4070 #whitepcbuild #whitepc #customloop #customloopwatercooling #watercooling #watercooled #ekwb #lianli #lianlio11dynamic #redpc #rtx4080 #rtx4090 - Věda a technologie
Don't miss out on the In-home setup for this PC's owner - Spencer Lee!
czcams.com/video/eMyKxDG_U94/video.html
deadass thought this was from a channel with 100k+ subs
Amazing video, keep up the great work
Appreciate the comment! We’re just a small channel who love PC and tech! ✌🏻
Amazing build!!
Glad you like it!
So freaking cool!
😎😎😎
Wow this gives me chillz this is perfect in every way i wish i had the money 🔥💯🔥🥰
This PC is dripped out 🧊
impressive build nice work
Thank you! Cheers!
Amazing!
Thanks!✌🏻
Damn this shit clean afffff
🤘🏻😤
Uffff Firee!!!
🔥🔥🔥
That is f*cking beautiful 🔥🔥🔥
💯🙌🏻
I’d love to do this for a living someday
You definitely can! We only started about a year ago so its totally something anyone can do!
so relaxing to watch
Glad you enjoyed! 😊
@@archetype_origins definitely i can watch it again and again
❤️
Im wanting to start to build PCs and this looks so cool, really want to learn how to do this
Awesome! Maybe we will do a step-by-step tutorial on how to do custom loop water cooling!
@@archetype_origins that would be amazing
@@archetype_origins I'm interested to see the step by step tutorial as well.
@@visa-schengenwf424 We would definitely keep this video idea in mind, we might take it happen one day! 🔥🔥
@@archetype_origins hopefully,
Its amazing how high quality the videos are and you can still respond within 2 hours to every comment
Thank you so much! 😉
Awesome build. Why didn´t you go for a 360mm pump reservoir combo, instead of a 240?
Even the 360mm FLT fits perfectly on the side, we decided to stick with the 240 instead because we wanted to use the bottom inlet and outlet. The 360mm FLT does not provides enough clearance to use the bottom holes.
How did you mount the flt240 I’m struggling to mount mine in the same location but with fans
awesome
Thank you!
I did the same thing. Bought all ekwb parts but used corsair rads. 😅
Can't see them much anyway!
Is it possible to put a distro plate on the front? I didn't want to give up adding 3 more fans...
You can still install your fans on the side and just mount the distroplate on top of it. The bracket that comes with it should provide enough clearance for airflow, we chose not to install fans because we think it looks cleaner this way.
Is it viable to have an AIO cpu and a separate water cooled loop for your GPU with a rad? thanks!
Absolutely! Most people do it the other way around which is only custom loop water-cooling their CPUs and keep their GPUs the way they’re but you can definitely do it the other way as well!
Is there any way to keep the watercooling and the 4080 and make this build cheaper
Absolutely, you can always choose to go with some alternative options such as Barrow and Bykski for a more affordable water cooling solution.
I've been trying to figure out what's the max radiator thickness that can fit at the top and ond the side, I'm curious if I can fit a 44mm rad on each.
I think you should be able to get away with a 44mm on each side, there’s plenty of space to work around with that. I definitely wouldn’t go any bigger tho
@@archetype_origins Thank you so much!
You are very welcome! 😉
What is the maximum height of the top radiator? My rad has a height of ~5cm, with fans ~7.5cm. Same on the bottom. Will they fit?
The hydro X 360 rad is 3cm and the fans are 2.5cm thick, that made it 5.5cm total. I do think your 7.5cm will fit on the top of the chassis but it’s definitely a tight squeeze. I’d recommend putting it on the side instead.
the distro plate link only includes the plate with no pump where do you get the pump?
I must’ve listed the wrong one, here’s the FLT 240 with D5 pump:
amzn.to/3rhIv4S
Looks amazing! But how does your four DDR5 planks system work?
It works well, I did not enable XMP in BIOS tho, figured it might cause instability.
@@archetype_origins Thank you.👍
Of course! :)
Its Cool ❤😊
😎
@@archetype_origins \,,/
From start to finish, how long did this project take?
I think it takes about 4 days for the building process, 7-14 days just to wait for shipping
How much for one of these
That is a beautiful piece of work!! I wish my hands still worked well enough to build one for myself!! Grats!
It does require a lot of dexterity to bend the tubing. Have you build a custom water loop before, @lyalsimon9618 ?
😮
Where did you route the lcd screen cable
Through the GPU slot and the back of the PC case
Does anyone know if the 4090 support this gpu water cooling block? Reply from creator will be very helpful also
No, this GPU waterblock is specifically made for the Zotac trinity 4080 GPU
Does the NZXT H9 support E-ATX motherboards?
You should be able to for most E-ATX motherboard, keep in mind you’ll have to unscrew the cover plate on the side, we did it in one of our videos, check it out!
czcams.com/video/qUZaRhYe1fU/video.html
Hello what is the size of that monitor and a link for it please ?
The monitor is 7 inches and linked in the description 😘
I am trying to get all the same parts and my birthday is coming in a few days up even with all the money I would get I will still be short any suggestions for cheeper parts im getting a B760-A should I go with a 13900k of a 13700k will a 13700k be good enough
13700k is more than enough for casual gamers, 13900k is definitely overkill for most users out there.
@@archetype_origins what do you think about the 14700k instead of the 13900k witch one is more powerful
For the most part, they have relatively similar performance. I would recommend going with whichever is cheaper at the time of making a purchase
what is that red screwdriver you used?
Links in description
why not buy the 7900x3d if its for gaming ?
7900X fits well within his budget, at the time of building, 7900X3D and 7800X3D haven't released yet
do you have a motherboard suggestion if I want a 13900k also would I need a different cpu waterblock
is a ASUS ROG Strix B760-A good? would I need a different cpu waterblock
If your budget allows, I’d recommend getting the ASUS ROG Maximus Z790 Hero: amzn.to/3LHEtdf
Yes, you’ll also need a LGA1700 socket CPU waterblock
If you’re looking for a one that’s similar to the EKWB Quantum Velocity, here’s the one that would work with Intel i9-13900k: amzn.to/3ZAs8gu
@@archetype_origins the rog maximus x790 is expensive are there any cheaper options
How much would something like this be?
if you are looking to get an estimate for your PC, kindly fill up the build inquiry form and we will get back to you as soon as possible! Thank you!
archetypeorigins.com/inquiries
👌💥💥💯💯👌
Ekran kartından çıkan sıcak suyun soğutulmadan işlemciye gitmesi ve sonra çift radyatörden geçmesi sağlıklı bir işlem mi?
How much does all the water coolin cost
Think it was around $2k
Are these available to purchase
Yes they are! If you are looking to get an estimate for a new system, kindly send us an inquiry and we will get back to you as soon as possible!
archetypeorigins.com/inquiries
whats the thing called u placed on the cpu where the old socket was? i dont mean the ek quantum velocity
It’s called a Contact Frame Anti-bending Buckle
amzn.to/43Aeg6q
@@archetype_origins great! thank you! im currently thinking of getting the same distroplate as you built in, but i wonder if the 360mm version will fit in too? i see youve mounted the 240 version, did u try the 360mm? Im worried the fans and radiators on the top and bottom wont let you mount a 360mm distroplate
Yes, you can still fit the 360 FLT in this case, you just won’t be able to use the bottom holes at all.
@@archetype_origins you mean the 2 lower holes from the distro plate? do i need them?
You don’t! But it’s worth mentioning so when you’re planing your route for your loop you know to not use them and cover them with the fittings cap
Imagine seeing this in a doctor’s office.
Do you ask or not ask? "Dr. is that the blood of your patients?"
total cost??
If you are interested in getting a custom PC from us, be sure to send us a build inquiry here!
archetypeorigins.com/inquiries
Totally cost ?
$6,500 🔴
Can you build this for me
Absolutely, if you are looking to get an estimate for your PC, kindly fill up the build inquiry form and we will get back to you as soon as possible! Thank you!
archetypeorigins.com/inquiries
i bet with better camera the built would look gorgeous
We shoot everything with our iPhones, but one day we hope to be able to get actual cameras.
wish you all the best, my support is with you @@archetype_origins
That is the best thing to hear as a creators 😭
Hi, are you
Uk based?
We are based in the US!
when i saw blood on the title , i thought u were gonna put ur period or something.
🤣that's a lot of 🩸
those nails are terrifying..
Wait until you see the newest video! They're even longer 😱😱😱
bunu bana verir misi nteşekkürler
We would be happy to build it for you! Head on over to our website to complete a build inquiry !
Take the Lian Li Streamer out. they look really bad :
Maybe we should take this comment out instead, it looks bad 🫨
Термопасту размазал это тихий ужас!
Option 1: OUT from the GPU into the CPU as you did it affect the temperature of the CPU?
Option 2: From the pump with 8 connectors: 2 IN and OUT for Radiator 1, 2 IN and OUT for Radiator 2, 2 IN and OUT for CPU, 2 IN and OUT for GPU. Then the container always has cool water to pass on. Do you find this way more effective?
1. It does not matter which order you choose to go first, it WILL not affect the overall temperature.
2. I don’t really understand the questions. However general rule of thumb is you always want to go through the CPU and GPU first, then to the radiator and finally back to the reservoir. Hope this answer your questions.