LED Flasher Circuit
Vložit
- čas přidán 19. 10. 2020
- In this video, I will show you How To Make Dual LED Flasher Circuit?
Visit my Website for Buying Links & more Information about LED Flasher Circuit: circuitbest.com/
Instructables: bit.ly/ccinstructables
Subscribe Here: bit.ly/Creativecrearor
**Note: Some People copy my content as well as the thumbnail. I have no issues with content as long they make it themselves. But for the thumbnail, It belongs to respective owners (Some also created by myself). If you get a copyright strike without any notice by copying my thumbnail then it is not my fault. Happy Creating :)
Needed Components Online Link-
Amazon US:
18650 Battery: amzn.to/3dITQ2O
18650 Battery Holder: amzn.to/3ofXBll
LED: amzn.to/3dH48QO
555 Timer: amzn.to/3jeOwVV
Resistor Set: amzn.to/2HfW5Ph
Soldering Iron: amzn.to/3dJIVpm
Capacitor Set: amzn.to/2Tc2DRg
Female Header: amzn.to/2TdGT7u
Amazon India:
18650 Battery: amzn.to/3m1oqHQ
18650 Battery Holder: amzn.to/3o80bJR
LED: amzn.to/35db7ND
555 Timer: amzn.to/37n1AGp
Resistor Set: amzn.to/31pfKmD
Soldering Iron: amzn.to/37oeST2
Capacitor Set: amzn.to/31o16Mm
Female Header: amzn.to/37kOs4M
♫ Epidemic Sound: bit.ly/2YQ2N42
I hope this video was Useful and you liked it if you did press the thumbs up button.
Cheers!
Creative Creator
:)
**Note: Use Heat shrink tube for making all connections Secure.
Follow Me On Social Sites
1. Facebook: / creativeideas365
2. Instagram: / creativeideas365
3. Twitter: / creativeidea365
------------------------------------------------------
Thanks For Watching
✅LIKE ✅SHARE ✅ COMMENTS✅ SUBSCRIBE
#DIY #LED #flasher - Věda a technologie
Hey guys how is going?
Schematics included in the video.
Visit: circuitbest.com
Bro i want you to make a wireless electricity transfer circut... it is simple, use single LED blinking circit with NE555P and change the capacitor value and make a coil of 50 turns and add a 50 ohm resistor in series with the coil and replace the Led with coil. at the reciver coil (30 to 60 turns) you will get above 100v but it is low power so no harm...connect a red led to reciver coil and you are done!!!
@@kunaldhar6713 ok next video in week
@@Creativecreator wOw tHANKS! :)
kf
This would have been a good video had it not been for that damn monotonous background junk accompanying a narrator...you can't turn it off without losing the speaker too.
Hard to believe, 50 years later, the 1 shot mono stable multi vibrator is still being found in projects. I built my first circuit with the 555 for my car. I built a delay windshield wiper circuit. . Around 1976
You made my day! This is what I needed! Simple and to the point. Thank You!!!👍
Your tutorial is very well explained and with the values of the components as well as the final diagram, which is rare, well done, except that you indicate the value of the 1 st resistor of 1k, while you have mounted a resistor of 10 Ohms . Thank you. I am French, I do not understand English and I do not know if anyone said that I noticed, that's why I put it
I was making these 25 years ago. Today you can buy led's that have this function built in. You just have to connect them to a battery. Great for bite alarms (carp fishing)
Really? Cause I can't find them. So id like to know where your buying them.
This is a flip flop circuit. Different than just a flashing led.
I could use flashing leds for my smoke alarm strobe
make this montage with what we have available.
so even if now there are simpler solutions, everyone does as they want.
@@adamcrownvictoriacarrepair7105jaycar. Element14 is out of stock.
555 Timer IC... One of the Best IC ever designed.😎
Bom dia, Mestre 👍👍👏👏 nota 10 !
Excelente trabajo amigo, saludos desde Venezuela..!
Another awesome video of assembly technique and electronic component function ! Thank you, from the old retired electronics teacher/video editor in Canada.
czcams.com/video/xXmgRCfeMro/video.html
Simple, practical and intuitive...Thank you!
Excellent videos! Great visual and audio descriptions. Thank you!
Great inventors are also frugal. How versatile is this circuit.!! Thumbs up. Thanks.
Great video Thankyou !!! I'm going to use this in a new Christmas light design this year. Next I need a chaser unit to run a relay board. I am making a row of wire cages to cover with white plastic to house coloured lights to chase along my driveway.
Fab video, thanks. Liked and subbed. I look forward to watching and learning more.
It's nice to hear you explain, plus your videos seem more informative now. I just started this stuff and you have taught me a lot over the last year. I remember all that "canned" corny music track in your videos. I actually started liking it :-)
Haha thank you so much 😌😌
Montei hoje cedo. Ficou ótimo
Thanks understood more of circuits by watching this than whan i understood from reading the two books on electronics the past days.
Thanks for the very good video!.. I believe that you would be better off by adding a resistor like 470ohm in series with the IC output (3) to minimize the power consumption. Note that IC NE555P will keep working even below 2.8volts, this is convenient if you are powering the circuit using standard batteries. Also consider that by changing R1 (I.e. to 100K) you can slow down the flash rate -same effect as changing C2. Furthermore if you only need only one LED you can simply leave out LED2.
GOOD
I tried with 1 led - doesn't work
Are these 3 volt led or 1.5 volt?
Hello,
thank you very much for sharing your video as it has been very helpful.
could you please tell me what was the last Capacitor that you used at the end of your video to cause the LED's to flash very slow?
Thank you . your english intonation is perfect
Thank you 😊
@@Creativecreator good project, u could have included circuit in the video itself.electronic hobbyist, sr citizen
All my videos have schematics at the end of the video please watch full video otherwise you will miss it.
Thank you for the video - the curcuit looks really nice (you can make simple things using very cheap components and then use them even for some household stuff etc,) And what you can choose any capacitor you need to adjust the blinking rate here is also very handy and real fun ;-) Good luck!
can you help?
@@bruceyoung1343 What exactly shall I help you with? ;-)
@@user-vd5iu6ku6y in past I saw a wire frame train for outdoor christmas lawn decoration. The way the lights were, the wheels seemed to turn. but it was they way the lights were timed to give that appearence. I would like to duplicate that lawn ornament for my lawn
Picture a wheel in old western covered stage coach. Now thinking the line in from the hub to the outside wheel, rods. Now picture light strings on those rods. Now picture every 3rd or 4rth rod would light up. then they go out and the next group light up/go out. next group and so on. That lighting affect would make the wagon wheel spinning I used to see these 30-40 years ago. Happy holidays to you and your family
Seeing your way of soldering is very poor not good .
Thank you so much for sharing this Mate.
This circuit can be used in various project situations. Thanks! from Brazil.
Hi - Great video
Question - I hooked up 2 x 0402 leds, worked ok except one led was brighter than the other. I placed a 560 Ohm resistor on the bright led as to match the brightness with the other led which worked. Running this circuit from my power supply at 4 volts, can you see any issues with this?
This is what I was looking for - Thanks
20 years ago i put somethink like this in my first car, a Oltcit Club made in Romania. Nice job.
Eu am făcut cu 2 tranzistoare BC 170, bistabil.
Ce vremuri. Am avut si eu pe o dacie.
@@mariusstanciu8843 AC128!
HubNut has on of those
Awesome video! How can I make a circuit like this where one LED is a very short flash, like less than 0.5 seconds, but the other is on for several seconds, like 15-20 seconds?
Good demonstration .thanQ.
muito bom é o que preciso parabens
Verry good. Hello belgium
Useful idea.
Do I need the resistors if I replace each LED with a neon LED strip that runs on 12VDC and my power supply is 12VDC? Each strip could represent a word like YES NO and the strips would alternate being lighted. Each neon LED strip is a self contained circuit of LEDs in parallel. There's a positive and a negative wire on one side of the strip, but the other side of the strip is closed.
hello i am just learning to play with leds,can you do this in parallel circuit and how many led's can i put in one circuit
Good and very clean n neat project however the resister 1 you mentioned is 1 k ohms , but in video it looks 10 ohms...it may be my mistake...kindly correct me if i am wrong...
Keep posting nice projects
Nicely Done!
I am trying to reduce the consumption of a 12v LED. Looking for an alternative for a 12v LED to not use full power to save the battery. I understand utilizing a step-down transformer or boost converters, however they use resisters which consume power. There is a minimum voltage input to fire up an LED which is about 8 volts. I would appreciate any help.
could this type circuit be optionally powered by one or two button (watch) batteries?
congratulations for your perfect speech
Great full
Is the reason for the difference of resistance in the led's to not be an issue, because you combined the negatives of the led's?
great video sir, I will try this tonight.
would it be difficult to have 2 led's flashing with a rechargeable battery in the circuit also a jack plug or usb linked in to charge the battery with ease instead of having to change the battery possibly to have it charged from 12v system
and on 24v or 12v can you use such a circuit?
great idea, the way you built it you can test electrolytic capacitors
Bro .... is strobe light effect ....water drops leviation and slow fall circuit avalable?
what are the wire strippers you are using and where in USA can I get them?
Thumbs up and subscribed. Can you show how you would reduce the output of a 12v battery powered LED in order to conserve the battery?
Really good ideas
is this scaleable to add more led?
What Voltage LED would you use in please
Thanks 😊
Music is soo hi
Can you show us how to create a circuit that detects atmospheric humidity using LEDs as the indicator? (IE: green led for low humidity, yellow for mid level humidity, Red for high humidity, blinking red for 100% humidity).
GREAT job man! Do you have a video of this for 12V circuit? Would like to build a pair for my SUV. Thanks
I will make buddy 😉
Thanks Bro!!
Hi, congratulations your job, But i have a question. I love eletrocnics, but i don`t understand nothing. I am dentistry. What do I do for this device? Continues making a great and symple projects.
Best of luck
Can we use any resistor
Dang, that was neat!
Good Idea, nice
GREAT SYSTEM. COOL
Christmas light flasher.........excellent.
Creative video, thanks :)
This seems impossible. The data sheet for the NE555 IC says the minimum voltage required for this chip is 4.5 volts. If this one works (18650 fully charged is 4.2 volts) it is probably a fluke due to IC chip tolerance's. It probably won't run very long once the 18650 drops below 4 volts. You can substitute the CMOS 555. (ie; TS555, LMC555, or TLC555 ) It is designed to run with a voltage down to as low as 2 volts.
Mantap master
Nice experience
Attach variable capacitor? Or change one resistor for variable version.
that's a cool video.
Мастырщики на коленке - заколебали. Дай схему и спи спокойно - лайк обеспечен! The scribes on their knees hesitated. Give the diagram and sleep well - the like is guaranteed!
can i use 5v or 12v dc supply for this circuit?
love it !
Thank you 😊
Muy Bueno. Very good 😀👍👏👏
I’m trying to duplicate spot soldering to build Artzy things. I cannot seem to hold a bead of solder on my Iron to apply to each component ( resistor, transistor..) Is the type of solder, temperature, flux ? sites like Apour Maker and yours
Can you please tell me how do I use this circuit for a 12v batteries and an led strip
Hello
GREAT WORK Friend.
Thanks for it.
How many led can we connect in parallel with Red and Blue?
Thanks
Is the "INPUT" pin of the NE555 IC the two pins 2+6 ? Right ? The "OUTPUT" is trivial and we all know it is pin 3 !!! :) Thank you very much..
nice & it is working
What capacitor would you reccomend for flashing each led for about 0.5 seconds? Also, can you use one of those ceramic capacitors ?
I found a 22uf is about 0.5sec ish
@@DairyNZ thanks m8
Very good information...Thank u
Great video, thanks
Muốn làm 3 trạng thái có được không bạn
Please let me know if I want to connect buzzer as continuity checker.
Bro I'm an absolute beginner and I hope you'd help me on this. I have a UV light for hardening the resin.
It works for 1 minute and turns off automatically after that. However, there is no display to show me the countdown, is it possible to make a similar circuit to that one with a small display that shows the countdown for 60 sec?
Very cool!
Awesome bro!!
Thank you 😁
Great job sir
wonderful
Thanks bro I did it working very well 😀😀
This project can be used in the 2 ways :
1st way as he showed
And in 2nd way we can blink a single led by removing led which is connected to the ground
Hi, is it ok if I use a 10k resistor instead of 22k resistor???Please answer me bro 🙏🙏
how vol iss vcc input master ?
Awesome. How can you get away without LED current-limiting resistors? Cheers!
if u dont care about the lifespan of that leds then you dont need current limiting resistors. The easiest answer...
Oh yeah if you want to know what i did then, i ran it of 110v power lines and now my face is black.
BTW Where did u saw current limiting resistors?? There are no current limiting resistor
what's the time duration this led flashes on 3.7 v
If I wants to install a dp-dt switch for 1 time 1color blink so where can I use it
Salut! Am si eu o problema cu circuitul, unul din leduri se aprinde mai slab decat celalalt. Am incercat cu alt integrat si cu alte leduri si tot la fel. De ce oare? Ma poate ajuta cineva cu o informatie?
Hi
How many led this flasher covet?
Sir, can i replace the resistors with potentiometer?
I just subscribed... Nice Job...! Do you make your own circuit boards also?
Hi thanks for the video I want to used this for a model and I need to use 4-6 SMDs and they light very dim dose any one know what I need to change please
Amazing
Thank you 😀
I'm trying to find if can make an LED stay on longer than the other...
👍👍👍👍👍👍👍 so cool KISS ..... E-KISS extra short and simple Just what I need for class.... 8-th graders... Thanks a lot Cheers
How many led can one 555 timer support
This ia good