Doing This To Your JEEP Wrangler Chassis & Suspension Can Save You Thousands How To - Maintenance

#jeeptj #jeeplj #chassislubrication
Official ATEM OFFROAD’s Super Store
www.amazon.com...
Excerpt from spicer:
Warning:
Inadequate lubrication can cause driveline failure, which can result in separation of the driveline from the vehicle. A separated driveline can result in serious injury or death.
In order to minimize the potential for driveline failure, including driveline separation, you must:
Carefully review the lubrication specifications in this brochure and lube manual located in our Literature Library.
Make sure you use only approved lubricants. We recommend Spicer® ultra-premium synthetic grease.
Make sure you lubricate at recommended intervals.
U-joint Kit Lube Procedures
Spicer® greasable U-joint kits contain only enough grease to provide needle bearing protection during storage. Prior to installing a new U-joint into the driveshaft, you must:
Remove each bearing assembly and pack each journal cross lube reservoir with grease.
Wipe a liberal coating of the same grease into the each bearing assembly, filling all of the cavities between the needle rollers.
Apply a liberal coating of grease into the bottom of each bearing cup.
Apply grease gun pressure to each U-joint until fresh grease appears at each bearing seal. This purging action not only assures that every bearing has been properly greased, but flushes out any moisture and abrasive contaminants that may have worked their way past the seals
The whole parts list I use on my Overland rig
Hi! Take a look at this List I created on Amazon. www.amazon.com...
More Awesome Content?
DIY Overland kitchen Tailgate table
• DIY Jeep Wrangler Tj ...
DIY Bolt On Hi-Lift J-Mount Install
• Video
DIY Front Stubby off-road bumper
• Jeep Wrangler TJ - DIY...
DIY Body Lift
• Jeep Wrangler TJ - DIY...
Jeep front and rear shock replacement
• DIY How To Replace All...
Sway bar quick disconnects
• $20 DIY Jeep Sway Bar ...
Overland Tool mounting Solutions
• DIY Overland Trail Car...
Jeep Tailgate table build
• DIY Jeep Wrangler TJ T...
DIY Jeep Rock sliders
• DIY Jeep Wrangler Rock...
How To Install cb radio in Jeep Wrangler
• How To Properly Instal...
32” tires I’m running
• 32” Tires On My Jeep W...
DIY On board air compressor build
• Jeep Wrangler Tj | Lj ...
Fuel and water cell mounting Solutions
• DIY Overland Jeep Wran...
DIY Rear Trail Cargo Rack build
• Jeep Wrangler- DIY Ove...
Hi jack hood mounts install
• Jeep Wrangler How To I...
Wireless winch controls
• How To Install An Opti...
DIY Jeep E Fan build
• DIY JEEP WRANGLER Elec...
A Good working drive train rust and corrosion free suspension, and chassis is very important under the jeep when Wheeling overland. In this video I tell a story how I Grease and lubricate my rear driveshaft suspension and bushings under the jeep wrangler . I hope you enjoy.. Thanks for watching! And if you haven't yet subscribed, DO IT!! Also hit the bell for awesome notifications by ME!! Thanks
How To Grease + Lubricate Overland JEEP Suspension & Chassis + Rust & Corrosion Protection TJ XJ YJ
How To Properly Grease + Lube Suspension & Chassis On Jeep Wrangler CJ YJ TJ XJ JK LJ
DISCLAIMER
Due to the factors out of control by ATEM OFFROAD, we cannot guarantee against improper use or unauthorized modifications of this information ATEM OFFROAD assumes no liability or responsibility for property damages or injuries incurred as a result of any information contained in this video. Use this information at your own risk . ATEM OFFROAD recommends safe practices when working on vehicles and or with tools seen in this video, any injury damage or loss that may result from improper use of these tools equipment or from the information contained in this video
Is the sole responsibility of the user and not ATEM OFFROAD. Be Safe
This video and description contains affiliate links which means if you click on one of these product links, I’ll receive a small commission.