I followed your steps and found I had corrosion on my electrical connector on the motor. It took less than 5 minutes. I was about to buy a new motor. No need to do that now. You’re the man. Thanks.
Mine has been hit or miss. Sometimes it will come on like normal. Other times, I have to hit a rough spot in the road while driving for it to come on. I just went out there, tapped the bottom of the blower twice and I came on. Just ordered a new one for $32 on ebay.. Dude you're some kind of handy! I've been wrecking my mind trying to figure this thing out. Thanks man!
did these steps and my blower motor resister plug was not plugged in or lose. did what you said left the truck on with the fan on, then pulled and replugged in that plug and magic, came on. thanks for the video.
I saw the first few minutes of your video I tapped it with the wire and then it works right away parrot thank you because I was having a heart attack because we're about to literally get a blizzard here in Philadelphia tomorrow and it's freezing thanks again you got it yourself a new subscriber
Dude saved my butt , just got bee resistor replaced and nothing ... watched this video went to tap on the motor turned the key and walla , it works and all speeds now work as well . Thank you!
Very helpful. Saved me a ton of stress, since I just had steering column and ignition work done, I was worried it wasn't relaying power where it was supposed to. Just a failing blower motor tho.
i hooked my buddy gene's right to his battery because the multi meter wasnt reading any power, blower motor works, now we just have to dink with the wiring harness. thanks for the video.
Watched your video. I’ve had this problem for along time. Only worked on high. Swapped out the resister and bam. Worked like a charm. Thanks you saved me some dough. Peace.
Thanks for the video! I had replaced the blower motor about a year ago along with the blower motor resistor. The other day the blower motor didn’t come on. I check the connector to the motor after watching this and bingo! Thank you again.
I'm having a similar issue you described here. Except the blower doesn't turn on at all. I'm not sure how to check to see if I'm getting power to the motor. When I put my volt meter on it didn't read anything. Just bought this truck thinking it was a switch and it wasn't the problem as far as I know
Thanks bro your video was helpful for me thanks cause of your explanation I got my ac going again the only thing I didn't check was my ignition switch that was it bad ignition switch thanks bro God bless you
Helpful Video - Thank you. My 2005 Dodge Ram recently started making noise on the "high" fan speed setting. Kind of an obnoxious hum sound. The other speeds worked up until yesterday. Now, they come on and off (When they are supposed to be on) intermittently or not at all. Would this be the Resistor? Or something else. I do not have a meter to test the electrical
Great video, what if the fuses blow immediately? I've unplug the ac controls, blower motor, blower registor, ac compressor, and ac sensor. The 10a fuse in the cab keep blowing when I turn the truck on. I moved the wires around under the steering wheel to see if there was a loose wire and then the 10a fuse worked. I plugged in the 40a fuse and relay under the hood. Immediately the rely went crazy when being installed, and the 40a fuse blew.
Swapped my batteries this weekend, and today I found out that my blower motor isn't running. (on all speeds). Haven't had the time yet (as I'm at work now) to check it out, but the point that the blower resistor is regulating with the amount of ground it provides where golden for me and will check this out later today. I suspect a blown fuse, and I'm not sure where I could source those 40A fuses here in Norway.
@@user-ln7of9gs4s I had to change the blower resistor one more time. Turned out that the blower had blown the new resistor. So I swapped both the resistor and blower, and it have been fine since.
Whats up my dude. I have an 05 1500. Trouble i have is fan dosen't work peroid. Did what you said and hit it. Checked power. have power at the motor but no power at the resistor. Checked power at the module nothing there. If you dont mind throwing your two cents in i would greatly appreciate it
I replaced the resistor, the blower motor and the blower motor connector relays but not that fuse and I still have no blower, any advice. I will replace that fuse today and see if it helps but I'm at a loss. any help will be great thank youi
Gotta question for you. My truck got broken into on an attempt to steal it. So my wheel column and key ignition was damaged. Now my windows air and radio only comes when ignition is forward. But when its crank none of it works.
This video seemed super helpful. But I checked the motor and replaced it doesn’t work. Fuse works. And it only works when I’m in motion so I don’t know what’s wrong with it. It has no corrosion and all the pins In the wires seem fine
Mine will blow intermittently. I’ve noticed when the ambient temp of the cab is hotter, it doesn’t want to turn on. It will work in all 4 speeds when it does turn on. Any ideas on what may be wrong?
Hey what if I'm getting 12v to the fan but it won't come on...also I man make the fan work with a Milwaukie battery but not while plugged i. Seems like it may be a ground issue like you were talking about
Hello greetings ! I have a question that is almost close to everything that you explains in the video.. i have a 2003 dodge ram 3500 and it gets the smell from outside to inside the cabin. and I wanted to know if that could be because of the climate control?.. because I also change it so that it blows air into the feet and nothing comes out. I don't know if that whole system works based on climate control:…hope you can answer my question thank you 🙏🏾
I have a 2004 ram 3500 Jimmy 5.7 when I adjust my Stern will up-and-down my fan will shut off and on as I move it up-and-down...lol... Have any ideas suggestions for me appreciate it thank you...
Mine was literally just not plugged in haha but without the video I didn't even know the blower motor was right there... the plug was lose just held it on with duck tape and you know what they say if duck tape doesn't work your not using enough duck tape!
La resistencia debe estar dentro al cambiarla para que no se caliente es cierto ?..la que puse se me empazo a quemarla prove fuera de su posición ...el abanico debe enfriar la resistencia
I have a problem with my blower motor not working and after watching some videos here at CZcams University I replaced my resistor, blower motor an it still will not work. I changed the ignition switch and checked the fuse (which is good) and it will not work ... my ignition switch was bad with a broken copper piece and burn marks ...What would you recommend I look into now? what the ignition switch did fix was the chime sound when the key is left in the ignition switch
Hey, so I followed everything and there's no power going to the resistor. None of the wires have power when ignition is on/vehicle running. Fuse is good under the hood. Is this pretty much pretty certain that the ingnition switch is most likely bad? Even though it starts and runs?
My issue is that the blower motor stays on after truck is supposed to be off. I can pull my key out the ignition and it still runs. I have to turn the knob to turn it off.
Hey my knob that controls the low to high speed for the van for the AC won't shut off when I turn it off. And the nothing comes out at all even tho it shows there's power! My question is where is the fuse that controls the blower motor?
I thought my blower motor was out. So I put a new 1 in. It only works if my steering wheel is in the tilt position? Any suggestions for me? Thank you God Bless
I have a 2004 Ram, looks to be same procedure, the blower motor came on when I tapped it with screwdriver and is intermittent when driving. Both connections looks good, no corrosion visible. Next step? Start with resistor?
What should the resistance be for the blower motor? Can I run wires directly to the fan motor straight from the battery n use a toggle switch to control it?
I jiggled ignition first with blower on and nothing so I pulled the blower motor out and used some gator clips to battery to check. Motor spun so must be resistor.
Do you know all the greasing points on the truck? Control arms I know are a grease point... is there ball joint grease fittings and front driveshaft? If there is let me know, and If there’s others let me know. Thanks. I have greased my control arms I have to look all over the components to find more... It sucks that they are hidden!
The issue im having is that my ac blower motor will turn on randomly. When it turns in the ac works great it blows nice an cold it may work for a day or 2 then stop working for who knows how's how long. Then once it quits working sometime if I leave it of an drive around for a bit I can turn it back in an it will come on an work fine with no issue. But sometimes it doesn't. But everytime it does decide it want to work it works at all speeds an blows ice cold it doesn't work but about 30% of the time an I can not figure it out for the life of me does anyone have any ideas how I might fix this issue? I did have $1100 in ac work done 6 months ago but when I took it back into let then look at it everything was working fine imagine that. But as an electronic tech I understand u can't diagnose an issue that not happening . Anyone's help would be greatly appreciated thanks.
Very helpful thank you. I have a question, not about the heater though. My 2005 dodge ram 1500, engine 4.7 does this odd thing. Ill drive it, when I stop for a red light or stop sign, the oil pressure goes to zero and the little lite comes on and dings at me. Then when I start driving again it goes back to normal. Would you know what the problem maybe? I was think the oil position sensor might be bad, not sure where its located. Lol What do u think? Erin
I would check the oil on your truck same thing was happening to mine and when i checked the oil it hardly showed anything on the dip stick to check the oil
Man what's your other video about the same Dodge I have a 05 Dodge 2500 now I made trips Wednesday night to come down here and see my girlfriend s*** it's about 2 hour drive I just got done changing the three knobs and the basically the control inside my truck cuz I was having issues of it not it was not coming on and it's been in there since factory so it was working fine again it was blown cold air it was all everything was good now on my trip to come see my girlfriend 30 minutes after I passed Austin it just quit and stop blowing it wasn't working I can hear the AC condenser clicking off clicking on when I'm going down the road if I put my hand over the vent it's blowing cold air but my fan is not kicking on I've replaced the relay I've replaced the the other thing that's next to the fan I took it to O'Reilly's they hooked up a battery to my fan and it's been like it was brand new please help me out
Could be a potential vacuum leak somewhere. I would check all of your hoses and connections then try again. I had a friend that his would only work when driving as wel and it was a leak.
So I got an 08 ram a few weeks ago and I starting having the speed problem. Usually would only work on low and then sometimes on high but never the middle two settings. Iput a new resistor in it and it worked on all speeds every time I got into the truck for about a week or so now it’s back to just working on low setting. Any thoughts???
@@JacksonGuitarsPlayer03 When I go film I am in the mindset that I'm gonna film nomatter what.. at the end of the day all that matter is I got the footage!
@@LehewTech yeah man there u Go. Lol I don’t know if that trucks yours or someone’s... probably someone’s but hey you are repairing it. Video I liked 👍🏼
I followed your steps and found I had corrosion on my electrical connector on the motor. It took less than 5 minutes. I was about to buy a new motor. No need to do that now. You’re the man. Thanks.
Mine has corrision to but i done replaced blower motor resister and it still not working
My guy, I got your video on a Google search, you saved my ass. My old 3500 dodge has a loose wire in the motor. It's minus 38 today thank you!
This video 4 years old but I appreciate you bro .
Mine has been hit or miss. Sometimes it will come on like normal. Other times, I have to hit a rough spot in the road while driving for it to come on. I just went out there, tapped the bottom of the blower twice and I came on. Just ordered a new one for $32 on ebay.. Dude you're some kind of handy! I've been wrecking my mind trying to figure this thing out. Thanks man!
Thanks Bud, thanks for mentioning the ignition switch could be going bad. I wiggled it with everything turned on and walla!
tapped it and it started moving but slowly. was great to know it was only the motor and an easy fix.Thanks for the great test instructions.
did these steps and my blower motor resister plug was not plugged in or lose. did what you said left the truck on with the fan on, then pulled and replugged in that plug and magic, came on. thanks for the video.
Bro you are a boss thank you! I been sweating bullets for two days without AC but all fixed not thx to this video!
Thanks a lot! Clear short and to the point.
Literally just tapped the blower and it came on, thanks!! Going to be super cold in the morning so glad you put this up!!!!
Thanks buddy you just told me what is going on with my truck I definitely subscribed to your channel
I saw the first few minutes of your video I tapped it with the wire and then it works right away parrot thank you because I was having a heart attack because we're about to literally get a blizzard here in Philadelphia tomorrow and it's freezing thanks again you got it yourself a new subscriber
This guy is good straight to the point. Thank you
Dude saved my butt , just got bee resistor replaced and nothing ... watched this video went to tap on the motor turned the key and walla , it works and all speeds now work as well . Thank you!
Very helpful. Saved me a ton of stress, since I just had steering column and ignition work done, I was worried it wasn't relaying power where it was supposed to. Just a failing blower motor tho.
i hooked my buddy gene's right to his battery because the multi meter wasnt reading any power, blower motor works, now we just have to dink with the wiring harness. thanks for the video.
Watched your video. I’ve had this problem for along time. Only worked on high. Swapped out the resister and bam. Worked like a charm. Thanks you saved me some dough. Peace.
Blower motor works on high but not a lot of air comes out of the vents
Good advice. Tapping on the blower work. Thanks 😊
I was able to fix my issue literally one minute into the video thanks !
Loo you are the best !! I tap the fan it it came back to live know I know what I have to replace
Thanks for the vid... barely touched a wire on the blower and kicked in so, looks like a loose plug.
Thanx... subscribed...like your clean clear thorough diag process
Thanks for the video! You saved the day bro!
great video. I just replaced the switch, resistor and blower motor. I have to check the fuse next. I did not know it was the #4.
First tap and it just roared on, you chad
Great video
I was about to take my truck to shop, all I did it was a tap on blower motor…
Thanks man this saved me from freezing
You’re the best…..thanks
Nice video love the kitchen gloves
Thanks for the video! I had replaced the blower motor about a year ago along with the blower motor resistor. The other day the blower motor didn’t come on. I check the connector to the motor after watching this and bingo! Thank you again.
A+ brother.
Thank You for this labor!
What if you have only one speed (max) and it's stuck on one vent setting?
Thank Yoi got me going cold again
awesome video. to the point, and very helpful.... great job man
I'm having a similar issue you described here. Except the blower doesn't turn on at all. I'm not sure how to check to see if I'm getting power to the motor. When I put my volt meter on it didn't read anything. Just bought this truck thinking it was a switch and it wasn't the problem as far as I know
You are a hero dude. Thank you!
Kept me from freezing Thanks!
Amazing!!! Thank you for the info!
Thanks bro your video was helpful for me thanks cause of your explanation I got my ac going again the only thing I didn't check was my ignition switch that was it bad ignition switch thanks bro God bless you
Thats great! I'm glad to have helped.
Helpful Video - Thank you. My 2005 Dodge Ram recently started making noise on the "high" fan speed setting. Kind of an obnoxious hum sound. The other speeds worked up until yesterday. Now, they come on and off (When they are supposed to be on) intermittently or not at all. Would this be the Resistor? Or something else. I do not have a meter to test the electrical
Thanks. Just helped me out!
Thank for the info. How do I replace the blower motor resistor?
Two screws. All you need is a Phillips. Can not get any easier.
Great video, what if the fuses blow immediately? I've unplug the ac controls, blower motor, blower registor, ac compressor, and ac sensor. The 10a fuse in the cab keep blowing when I turn the truck on.
I moved the wires around under the steering wheel to see if there was a loose wire and then the 10a fuse worked.
I plugged in the 40a fuse and relay under the hood. Immediately the rely went crazy when being installed, and the 40a fuse blew.
So the blower motor in my 2004 works well, But the problem is that on long distance driving, the air almost stops blowing out. Any suggestions?
There at 3 knobs and 2 buttons - one above the other on the right === what are the two buttons for? Please help . . .
What about all that isn’t working . How do you test the power going from the fuse to the ignition and then to the relay
Can you do radio parts next? I got my truck back from a shop with the radio and one of my lighter outlets not working and I cannot figure it out!
Thank you!
Swapped my batteries this weekend, and today I found out that my blower motor isn't running. (on all speeds).
Haven't had the time yet (as I'm at work now) to check it out, but the point that the blower resistor is regulating with the amount of ground it provides where golden for me and will check this out later today.
I suspect a blown fuse, and I'm not sure where I could source those 40A fuses here in Norway.
What was the issue? Thanks.
@@user-ln7of9gs4s I had to change the blower resistor one more time. Turned out that the blower had blown the new resistor. So I swapped both the resistor and blower, and it have been fine since.
Whats up my dude. I have an 05 1500. Trouble i have is fan dosen't work peroid. Did what you said and hit it. Checked power. have power at the motor but no power at the resistor. Checked power at the module nothing there. If you dont mind throwing your two cents in i would greatly appreciate it
I replaced the resistor, the blower motor and the blower motor connector relays but not that fuse and I still have no blower, any advice. I will replace that fuse today and see if it helps but I'm at a loss. any help will be great thank youi
Gotta question for you. My truck got broken into on an attempt to steal it. So my wheel column and key ignition was damaged. Now my windows air and radio only comes when ignition is forward. But when its crank none of it works.
This video seemed super helpful. But I checked the motor and replaced it doesn’t work. Fuse works. And it only works when I’m in motion so I don’t know what’s wrong with it. It has no corrosion and all the pins In the wires seem fine
That’s great so how do I test the switch and how do I pull it out to replace it.
Can u change the knob for blower speed. I'm going to try what u showed this morning first.
Mine will blow intermittently. I’ve noticed when the ambient temp of the cab is hotter, it doesn’t want to turn on. It will work in all 4 speeds when it does turn on. Any ideas on what may be wrong?
Hey what if I'm getting 12v to the fan but it won't come on...also I man make the fan work with a Milwaukie battery but not while plugged i. Seems like it may be a ground issue like you were talking about
Hello greetings ! I have a question that is almost close to everything that you explains in the video.. i have a 2003 dodge ram 3500 and it gets the smell from outside to inside the cabin. and I wanted to know if that could be because of the climate control?.. because I also change it so that it blows air into the feet and nothing comes out. I don't know if that whole system works based on climate control:…hope you can answer my question thank you 🙏🏾
I have a 2003 the I can't get the heater to change from defrost to vents what do I do to get it to change
Blend door broken
I have a 2004 ram 3500 Jimmy 5.7 when I adjust my Stern will up-and-down my fan will shut off and on as I move it up-and-down...lol... Have any ideas suggestions for me appreciate it thank you...
Mine was literally just not plugged in haha but without the video I didn't even know the blower motor was right there... the plug was lose just held it on with duck tape and you know what they say if duck tape doesn't work your not using enough duck tape!
La resistencia debe estar dentro al cambiarla para que no se caliente es cierto ?..la que puse se me empazo a quemarla prove fuera de su posición ...el abanico debe enfriar la resistencia
I have a problem with my blower motor not working and after watching some videos here at CZcams University I replaced my resistor, blower motor an it still will not work. I changed the ignition switch and checked the fuse (which is good) and it will not work ... my ignition switch was bad with a broken copper piece and burn marks ...What would you recommend I look into now? what the ignition switch did fix was the chime sound when the key is left in the ignition switch
Hey, so I followed everything and there's no power going to the resistor. None of the wires have power when ignition is on/vehicle running. Fuse is good under the hood. Is this pretty much pretty certain that the ingnition switch is most likely bad? Even though it starts and runs?
My issue is that the blower motor stays on after truck is supposed to be off. I can pull my key out the ignition and it still runs. I have to turn the knob to turn it off.
Hey my knob that controls the low to high speed for the van for the AC won't shut off when I turn it off. And the nothing comes out at all even tho it shows there's power! My question is where is the fuse that controls the blower motor?
With the last comment you made regarding the max or max and min speeds are only available, is this issue only with the ground resistor?
Hey..my truck is just blowing on high speed..so if it's corrosion and the resistor would I have to replace the resistor cord? How do you clean it?
2003 dodge ram SLT. blower motor stays on until it drains battery?
I can see so much power waves like clouds coming out of switch. Ha ha
My 2007 Ram has the same setup
Thank you working now
I thought my blower motor was out. So I put a new 1 in. It only works if my steering wheel is in the tilt position? Any suggestions for me? Thank you God Bless
I changed my blower motor resistor snd blower motor itself, everything works except the lowest speed. Try the switch next?
Ok so tapping on it worked for awhile but now its not working at all doesnt matter how hard i tap or where i tap what do i do
why does my heat and ac come on but when it’s cold outside it only blows cold and when it’s hot it only blows hot air would you know why that is?
Thanks ur bad ass
I replaced blower motor and resistor it only kicks on sometimes any advice
I have a 2004 Ram, looks to be same procedure, the blower motor came on when I tapped it with screwdriver and is intermittent when driving. Both connections looks good, no corrosion visible. Next step? Start with resistor?
Probably the blower motor itself if it came on after you tapped it
What if the control module isn't geting power
Can you go over troubleshooting the resister
What should the resistance be for the blower motor? Can I run wires directly to the fan motor straight from the battery n use a toggle switch to control it?
I jiggled ignition first with blower on and nothing so I pulled the blower motor out and used some gator clips to battery to check. Motor spun so must be resistor.
Do you know all the greasing points on the truck? Control arms I know are a grease point... is there ball joint grease fittings and front driveshaft? If there is let me know, and If there’s others let me know. Thanks. I have greased my control arms I have to look all over the components to find more... It sucks that they are hidden!
The issue im having is that my ac blower motor will turn on randomly. When it turns in the ac works great it blows nice an cold it may work for a day or 2 then stop working for who knows how's how long. Then once it quits working sometime if I leave it of an drive around for a bit I can turn it back in an it will come on an work fine with no issue. But sometimes it doesn't. But everytime it does decide it want to work it works at all speeds an blows ice cold it doesn't work but about 30% of the time an I can not figure it out for the life of me does anyone have any ideas how I might fix this issue? I did have $1100 in ac work done 6 months ago but when I took it back into let then look at it everything was working fine imagine that. But as an electronic tech I understand u can't diagnose an issue that not happening . Anyone's help would be greatly appreciated thanks.
Is a 2002 dodge ram the same as a 2003?
Very helpful thank you. I have a question, not about the heater though. My 2005 dodge ram 1500, engine 4.7 does this odd thing. Ill drive it, when I stop for a red light or stop sign, the oil pressure goes to zero and the little lite comes on and dings at me. Then when I start driving again it goes back to normal. Would you know what the problem maybe? I was think the oil position sensor might be bad, not sure where its located. Lol
What do u think?
Erin
The oil pressure switch is a good place to start. When was the last time you had an oil change?
@@LehewTech it was about 6-7 months ago.
I would check the oil on your truck same thing was happening to mine and when i checked the oil it hardly showed anything on the dip stick to check the oil
oil pressure sensor
@@erambeau77 maybe your oil.pick.up is screen is plugged i cleaned it. Never had issue again
Man what's your other video about the same Dodge I have a 05 Dodge 2500 now I made trips Wednesday night to come down here and see my girlfriend s*** it's about 2 hour drive I just got done changing the three knobs and the basically the control inside my truck cuz I was having issues of it not it was not coming on and it's been in there since factory so it was working fine again it was blown cold air it was all everything was good now on my trip to come see my girlfriend 30 minutes after I passed Austin it just quit and stop blowing it wasn't working I can hear the AC condenser clicking off clicking on when I'm going down the road if I put my hand over the vent it's blowing cold air but my fan is not kicking on I've replaced the relay I've replaced the the other thing that's next to the fan I took it to O'Reilly's they hooked up a battery to my fan and it's been like it was brand new please help me out
What about the AC works only while driving ? Not driving it’s not throwing cold air
Is the AC condenser fan under the hood working when the ac is on?
Lehew Tech nope not working at all
Could be a potential vacuum leak somewhere. I would check all of your hoses and connections then try again. I had a friend that his would only work when driving as wel and it was a leak.
If my fan is blowing weak is that the resister or the blower motor
Changed blower motor and blower motor resistor and still not working. Fuse looks good. What is next step?
why my heater doesn't through hot air
Have you ever cleaned the inside of your truck?
It's not his truck, and you can clearly see it's in a junkyard :)
So I got an 08 ram a few weeks ago and I starting having the speed problem. Usually would only work on low and then sometimes on high but never the middle two settings. Iput a new resistor in it and it worked on all speeds every time I got into the truck for about a week or so now it’s back to just working on low setting. Any thoughts???
Figure it out?
I need help!
Ya inghition
That poor interior
Yea one of the worst I've seen
@@LehewTech like how can u even touch it? The original owner (or owner) of that dodge a slob. Touching all that shit with his bare hands also
@@JacksonGuitarsPlayer03 When I go film I am in the mindset that I'm gonna film nomatter what.. at the end of the day all that matter is I got the footage!
@@LehewTech yeah man there u
Go. Lol I don’t know if that trucks yours or someone’s... probably someone’s but hey you are repairing it. Video I liked 👍🏼
Thanks dude. Yea its not mine I filmed this at a junkyard.