Bitrate for CCTV (how to control the bandwidth)

Bitrate for CCTV (how to control the bandwidth)
👍 Recommended Guides
✅ The Ultimate Security Camera Guide V1
learncctv.com/...
✅ The Ultimate Security Camera Guide V2
learncctv.com/...
✅ The Ultimate Security Camera Guide V3
learncctv.com/...
👍 Recommended Products
SECURITY CAMERA KIT
------------------------------------------
4K 8CH PoE Security Camera System
👉 learncctv.com/...
IP CAMERAS
-------------------------
Wire-Free Pan & Til Camera with Rechargeable Battery
👉 learncctv.com/...
Wi-Fi Rechargeable Camera
👉 learncctv.com/...
🔎 OTHER PRODUCTS
----------------------------------------
Surveillance Internal Hard Drive HDD - 3.5 Inch
👉 amzn.to/2UVYzGz
👉 amzn.to/2JWag9K
Powerline Adapter (IP data over electric wires)
👉 amzn.to/2xgFhmf
CCTV Balun
👉 amzn.to/2XrFFZN
Wi-Fi Extender
👉 amzn.to/3aX21X7
Smart WiFi Router
👉 amzn.to/3aYlTZZ
HDMI Extender Over IP
👉 amzn.to/3eeU1mv
Under $25 Wi-Fi Camera
👉 amzn.to/2VhviF7
This Channel is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. This means that, at no additional cost to you, we may earn a small commission for qualifying purchases made through the links on our site.
#LearnCCTV
#LearnCCTV

[@LucasGuardado]

Excelent explanation! thanks for sharing it

[@azardeen7454]

Nice seminar thanks for useful information

[@csk4j]

Love all your videos! Thank you.

[@LearnCCTV]

Thanks.

[@magallaneroyo]

It is incluiding those IP Camaras conected to the NVR IP ports or for those IP Camaras connectd through Ethernet Network port? Or both?

[@magallaneroyo]

Este calculo es para aquella camaras que están conectadas directamente al NVR por uno de los puertos IP o las que entran por el puerto Ethernet de red? O sirve para ambos casos

[@domingojrmarcos4943]

Thanks

[@LearnCCTV]

You are welcome.

[@ameenajma1]

Great info and thanks

[@timelineautomation3630]

Great !!!

[@AllClips7]

Hello, Friend I bought Swann 8 channel Nvr 8580 with 8 4K spotlight cameras. I’m using 6 cameras and running on cat 6 network cable. Everything is fine but vehicle and human are moving slow. Like kind of video lag. I update firmware and reset all settings still same issue. Could you let me know how to fix it.

[@LearnCCTV]

Check the FPS (frames per second). You should see smooth movement with 15 FPS or higher. Sometimes you need to reduce the resolution to be able to increase the Frame Rate because some systems can't handle both parameters higher at the same time.

[@AllClips7]

@@LearnCCTV I setup resolutions 2560x1440 20fps then little bit smoother. But with 3840x2160 resolutions frame rate is not going over 15. If I keep using 2560x1440 resolutions the video quality will be low or it will be same. Frame Interval is on 30 need to be change this one too.

[@pg7917]

excellent

[@LearnCCTV]

Thanks.

[@geniusbboy]

good

[@LearnCCTV]

Thanks

[@LearnCCTV]

👉 Download the Free Guide: learncctv.com/free-guide
▶️ Video Course - Free Trial - learncctv.com/skill-ytc

[@86lig]

Qmy jn

[@derbiyoussef212]

Top

[@anwarhossain9387]

I am problem off cctv network speed