How to MODIFY an INPUT or OUTPUT signal in Johnson Controls CCT Software

Modifying a control signal in Johnson Controls CCT Software is a very easy process if you follow a few basic steps. Writing a control program for a system is made much easier using tricks like this.
My Website: systemcontroltech.net/
Facebook: / systemcontroltech
NETGEAR 5-Port Gigabit Ethernet Unmanaged Switch amzn.to/30d9DST
Cable Matters 5-Pack Snagless Short Cat6 Ethernet Cable amzn.to/2zbLIbk
Onicon Controller: amzn.to/3eYEyXh
Onicon Insertion Flow Meter: amzn.to/3eMQDOU
Support the channel by becoming a Patreon: / systemcontroltech
Here are some of the things I keep in my tool bag.
Backpack: amzn.to/2tDnYsC
My screwdriver: amzn.to/2uPyIDV
Small fuse puller: amzn.to/2uPIdDk
Combination fuse puller: amzn.to/2vB0dPf
Adjustable wrench: amzn.to/2us3akS
USB to Serial converter: amzn.to/2vAKHTD
Network cable: amzn.to/2vBpJE0
Network switch: amzn.to/2eHsIa7
Hex Key set: amzn.to/2eHvA6C
Fluke meter: amzn.to/2tDaZHj
Fluke temperature meter: amzn.to/2tDxnQO
Dell 32 bit laptop: amzn.to/2us2Z9n
Serial cable: amzn.to/2eHvyf8
Johnson Controls DX-9100-8454 amzn.to/38VgLni
Johnson Controls DX-9100-8990 Back Panel: amzn.to/2IPQa0H
Johnson Controls AS-UNT110-1 - UNT Controller amzn.to/32CVnBB
Johnson Controls, Inc. Unt Series Unitary Controller amzn.to/2SpZCM9
METASYS AP-VMA-1440-0 APVMA14400, VMA Controller, amzn.to/2St5eW3
Johnson Controls, Inc. Fx Vma amzn.to/2XWEPFS
Johnson Controls Metasys NAE MS-NAE5521-0 amzn.to/2Yhyvbn
TRENDnet USB to Serial Converter, amzn.to/2JOxH4y
Johnson Controls T-4000-119 Allen Head Adjusting Tool: amzn.to/2Ygf7LS
Johnson Controls T8590 Residential High-Resolution Color Touch Screen Digital Room Thermostat amzn.to/2JVUhZf
Johnson Controls A99BB-600C Penn Series A99 PTC Temperature Sensor amzn.to/2Ycet1R
Johnson Controls P70LB-6C Dual Pressure Control, SPST amzn.to/2YhO8zq
Johnson Controls VA-4233-AGA-2 Electric Actuator, amzn.to/2JVVcZH
JOHNSON CONTROLS METASYS MS-FEC2610-0 MS-FEB2610-0 CONTROLLER amzn.to/2JT1Qj8
Johnson Controls M9220-GGA-3 amzn.to/32HRVpm

[@marimuthum1352]

Very nice, sir , but through this controller, how to include energy saving formula controller itself ,

[@Systemcontroltech]

That is done at the supervisory device level.

[@jeffvanmeerbeek3923]

We had v14.1 and upgraded to v15. In both versions we started getting an error when attempting to upload or down load a file stating: (Failed operation details: Access to the path archive moi is denied.
Any one know how to correct this

[@Systemcontroltech]

Under define hardware, reselect the controller. There's some kind of bug that is known

[@skyheatingair]

Hi , I'm one of your subscibeder , I'm working on PCG2611 controller currently had RTU program running on it , I would like to to replace the program to central heating/ Boiler , I'm able to discover the controller thru map getaway or old Bluetooth , I can read and write to it I can downloads the same program to it and check mark the main and the Boot if I want too ,, the RTU program on pcg2611 main 6.2 Boot 6.2 ,,,my ruining software CCT 15.0 release mode 10.2 firmware 6.2, so far so good But when I build boiler program and try to push it / downloads to the device ,,thru the commission summery its sees the PCG2611 when I hit next it will (CTT) start thinking then massage popup says ( please select a different device or different connection point to access this devices ) only when I try to changed the program but if I want to keep the same program and add to it such sensor or logic the downloads to it back will take it ?? would you pls advice me and let me know why , as usual I appreciate all your help .THANK YOU .
Abe

[@Systemcontroltech]

I run into that sometimes. Under the "define hardware" tab, reselect the controller you are using. I'm not sure why, but that sometimes seems to help.

[@skyheatingair]

@@Systemcontroltech
That's exactly what the issue!
Thanks I appreciate your response.