Full engine bay restoration 5 Cylinder Audi Coupe GT
Vložit
- čas přidán 20. 08. 2024
- In todays video I take you through the full process of restoring the engine bay on my Coupe GT, enjoy!
As always, don't forget to follow the socials:
resto_nation
restonation1
And check out the website if you want goodies:
www.resto-nation.co.uk
#enginebay #restoration #transformation
Your attention to detail is second to non, had a red Coupe with the same engine around 1991, I think it was 5 years old at the time , and the engine bay never looked that good, still have fond memories , great content keep it coming
Thanks! When I start I can’t stop… mot soon 🤩
The difference is staggering! Your hard work has paid off, I think the rivet counters would be happy too!
Haha! Cheers Jim 😎
Very nice job.
Looks great!
Thank you!
I've just done quite a bit of mine
Your video was very helpful too. Love my GT. Pity last owners didn't seem to
Really enjoying your restoration, I had an 88 1.8 GT back in the day in white also.🙃
I still miss mine… and it’s back up for sale on car and classic as we speak!
Wow, amazing work, just amazing!
Superb job as always James. Someone is going to be very lucky to own that if you decide to sell.
Cheers neil, it will have to go after I’ve had my fun and done some test miles. It will fund a new roof and then it’s full steam ahead for project mr2…
Looking absolutely fantastic, great job! At 2:43, that's the warm up regulator, which basically increase fuel enrichment when the engine requires it, i.e. during the warm up period, and full throttle. The cold start injector is on the inlet manifold near the throttle body, usually with a blue electrical connector, that basically just sprays some extra fuel in when cranking for a short period (longer when cold), to get it started.
That’s great thanks for the info! I thought it was a timer to supply fuel to the cold start injector. Nice to know that it adds some fuel under heavy load too!
@@Resto.Nation yes, looks like yours has the vacuum attachment, so if it's working correctly it will provide a richer mixture with lower vacuum (i.e. high load). The thermo time switch, which controls when the cold start valve/injector sprays, is located on the back of the engine block (i.e. bulkhead side). I've got an Alpine White Coupe GT too, mine's a pre-facelift so hopefully see you at a show at some point, be interested to compare them! 👍
@@markf4720 that sounds perfect. If there are any between now and the imminent winter then I would be keen… thanks again for the info.
@@Resto.Nation probably next year now for me, unfortunately mine has a gear selection issue which I trying to sort at the moment. Rebuilding the linkage and replacing clutch cable in the hope that sorts it... Otherwise it's out with the gearbox, replace clutch and bearings! Audis in the park seems an obvious choice for next year, I hope to be there!
@@markf4720 shame your having problems. I hope mine stays issue free. Audi in the park sounds great. If I’ve still got the car then I will go!
Кстати,эта "раздражающая" кабельная стяжка заводская ))
Looks fantastic lovely job can u come and do mine please 😅
Been there, done that. Only mine was a proper LHD car, as Germany intended it. That master cylinder doesn't belong there and you know it.
Use alloy wheel cleaner on the alloy
WOW, that looks superb fella! I would love to own this car
Thanks Andy! Now is that “would love to own because it’s nice” or “would like to buy it” haha. I want to use the car after the mot for a bit but it will have to be sold to keep the garage project moving…
Looking very nice 👌🏼
Epic channel mucker
Cheers bud 👍🏻
Where are you buying the parts? I'm restoring a 1985 Coupe GT.
That's not the cold start injector, but rather the warm up regulator. Cold start injector is into the intake manifold.
I used AUTODOC in Germany. Takes a few days to arrive but unbeatable on price 👍🏻.
Good luck with yours
nice work, but I guess you have very good reason why you did not pull out the engine. Now when it looks so nice these small rusted parts of the frame inside engine bay are bit annoying to me. But maybe I am not best to judge because rust is really something I can not stand :). Nice work! liked it.
Thanks. I just wanted to show what could be achieved without engine removal. I agree with you on the rust on the slam panel… but where do you stop haha!
It would have been good to see how and what you used to paint the parts etc.
Same with cleaning. Show some examples please.
Great job, looks very nice.
Fair. Which bits would you like to know?
The majority was engine enamel back for the block and silver for the other bits. Also some hammerite direct to rust silver spray for brackets etc.
@@Resto.Nation on the engine block for example: how did you clean it? What tools did you use? Did you use a paint brush or spray? What about the hard to reach areas, any tips here?
Man that looked like a dumpster fire when you first opened the hood.
Was the ambulance getting there early just incase you dropped the block on your toe
No chance, my good friends axle stand was supporting it…
Oh and someone sent me a design for a plate to remove that brake extra assist.. Its so not needed and ugly too
Remove which but sorry??
I swear I saw the part but it's not on your engine. Its fitted above the WUR and you have the casting pattern for it on the engine. Its to give the brakes extra vacuum boost when needed. I can't add a picture.
@@kevpetchey1409 is yours a uk?
@@Resto.Nation no it LHD and built for the Switzerland market
@@kevpetchey1409 that much be why 👍🏻