ZERO Scooters hydraulic brake Install
Vložit
- čas přidán 4. 07. 2024
- The new Nutt hydraulic brakes is easy to install on the ZERO 9, Z10, Z10X and Z8X. This installation of the front brakes on the ZERO 10X is just an example of the steps involved but this applies to all models. The whole process if done by a non-professional takes one hour and no complicated tools are needed.
Here are the steps:
1. Remove the original red brake calipers
2. Plug and place the nutt brake calipers onto the original mount
3. Tune the brakes to ensure the brake pads are not rubbing
4. Thread the hydraulic brake hose through the frame using the old brake hose as a guide (there are many ways to do this)
5. Insert the valve cap into the other end of the brake hose and screw into the brake lever by tightening the nut
6. Test brake lever for tightness. Brakes should depress halfway.
7. Connect the electronic brake wires
8. Test e-brake connection using brake lights
For more information on the e-scooter featured, please visit www.falconpev.com.sg - Auta a dopravní prostředky
Find these special brakes here www.falconpev.com.sg/products/hydraulic-brakes-for-zero?variant=15339841478
You can also find the bleed kit here www.falconpev.com.sg/products/universal-bleed-kit
Can you guys make a video on how to replace new stem please.
Mine is bent and I want to replace.
For the hydraulic brakes like the manual ones.
Can I lightly tap the brake to slow down but not completely stop?
Do you need that special tool for the fitting in the end if brake line
The olive connector, which reference is? Due I live in South America I want to know if the sram olive conector is suitable for nutt breaks?
Hi falcon pev can you give some advice about the installation that im planning?
1. I have my previous hydraulic brakes from my mountain bike that is compatible with my eks particularly redline same with zero it has stock mecha nical brakes
2. It has no sensor.
3. Im planning to buy magnetic sensor for e-bikes, replace my stock sensor for my eks.
Will this setup work? Thanks and more power to eks community.
Zero 8,9&10x needed front stem neck like zero 11x that be cool if they had in all lined up for mad collections 🙏🙏 ✌️✌️
Hello sir. How do these compare to shimano 6100 brakes in terms of braking perfmance if I may ask? Also how does this model do against its NuttA1 type counterpart ? (for mtb) Thank you
The wheel and brake disc are almost the same size so break power is very good even with the original breaks. What I would be interested in are ABS breaks.
bogdan9 ABS brakes are actually electronic braking in the controller not in the actual brakes itself.
This brake disk can i put it in zero 8 front?
Thanks guys, I have a set of these on the way.
Do you know what upgrade suspension can be used? I assume 165mm standard shocks... would 180-200mm work do you know?
I like to know also.
hey FALCON. Can I order these for a ZERO 8X?
What is the tool called to insert the valve into the brake line?
Is it worth it to Install nutt hydraulic brakes on the 52v version? I can get a deal for the zero 10x + the hydraulic + installation + wobbling clamp for about 1500 usd, take the deal?
is there a specific needle head size that's required for this? I bought a kit for my zero 10x and the needle heads weren't included.
Dalset I have the same problem I bought the kit from REVRIDES.com and it did not come with a needle bolt for front or back.
hi is it a diffrence if you allready have zoom brakes on the zero 10 x ? mine has the zoom brakes an i have an issue with the rear brake i want to switch it to the nutt brakes
Nutt brakes are indeed better. Made in Taiwan Nutt brakes are used on many high performance scooters
I recommend higher quality washers. Those conical washer can easily slip and scrape on the disk.
Splodgo conical washers are typically used to adjust height on brake Calipers.
hello there i want for sure to purchase your hidraulic braking set up...but there is the problem...in video you are cutting the wire.is necessary to cut?
RemarkablePoint no it’s not necessary anymore. We made it easier. Search for our latest zero 10 hydraulic brake video.
Sorry also I was thinking about you are cutting the hydraulic wire...
Nice. Do they need bleeding/purging following install and if so how? Thanks.
I want to see also but they dont back as I see, guess we need to ask someone in a bike shop or have it done by someone at a bike shop who know about hydraulic breaks.
Rocky Hernandez video said pre bleed
Thanks for doing this video. Want to know if these brakes will also fit up to a turbowheel lightning scooter like the zx-10. Also what are the tires you have mounted ?
Are they 120/90-10-57 Michelin reggae type ?
Look forward to your reply and thanks again...
Gary Linnert no idea if they will fit that model. It’s not the same.
@@FalconpevSg
Thanks for your reply. Will keep looking for the answers. Cheers GL
My leaver goes in all the way how can I fix it
Do these hydraulic brakes require special brake pads? Or can I use original brake pads?
Matt Brown it comes with brake pads. But yes it uses special brake pads
Can I do this for apollo explore
Yes should be ok
Can I use this to replace rear drum brake on Zero 9?
I don't believe you can buddy.
How do you top up the mineral oil reservoir.
Ray Scott find on CZcams how to bleed hydraulic brakes
pls advise me where i can place an order of zero 10x or 11x? thanks in advance
pow T.v Monitor www.falconpev.com.sg
Hi everyone: I have the Yume D5 scooter and I want to install the brake too. do I have to solder the cables for the e-brake together and why? I thought it would work if I just cut it off?
Depends on whether you want ebrake.
@@FalconpevSg I don't want this e-brake. I can do without it because it then brakes too hard and is not good for the engine. so can i leave the cables open without soldering?
@@Pirelli. yes you can leave it open no problem. But you can actually reduce ebrake power by adjusting the lcd settings
@@FalconpevSg OK thanks. then i will remove the cables. I don't need the engine brake anyway because it brake too hard for me.
My handle pulls all the way back before the hydraulic brakes engages how do I adjust that?
Joseph Kadabra you may need to rebleed the brakes. But a way around it is to double pump the brakes
does needle and olive from shimano breaks serve for this?
it is easy to miss but the olive and needle are included in the nutt brake pack. The needle is under the little cap at the end of the hose. czcams.com/video/PYrPfy2GTmI/video.html&feature=emb_logo this video helped me understand that!
Any suggestions on how to press the brass needle fitting into the tube ? I don’t have the press tool there using or can you supply a link on where to purchase one.
dwane crow actually you don’t need the tool. Look at our other hydraulic brake video to see how to do it
I have a zero 10X I bought the nutt hydraulic kit and watched the install video thanks unfortunately my kit only came with one collar so I’m headed to the bike shop on Tuesday.
dwane crow not sure where you bought from but the ones from us works like this: czcams.com/video/Kew7gYhGvUM/video.html
Falcon PEV I bought my 10X through REVRIDES.COM
Where can i find and buy that needle hose tool?
any online bike part supplier have them pretty cheap.
No the pads shouldn't rub at all even when they're new. And you can centre the calipers by loosening the bolts and clamping down the brakes
If my scooter is going no faster than 25km/h is there any real benefit of upgrading the brakes like that?
A Viking hydraulic brakes are not needed at that speed.
I've bought you're zero10x kit for my vsett9, do I need to cut the tubes? Or it will be OK?
Ty
Can you email us and we can help you with it
@@FalconpevSg ok thank you
@@FalconpevSg email sent ;) I need to know, if I need tools and oil brake, or it can be ok with your prefill tubes, cut size.
Hi, I have a zero 10x and I'm getting an error code on the display with flashing rear lights and the throttle doesn't work. I've tried pressing the brake 3 times on each side that doesn't work. Can you tell me what the white and yellow wire does, also black and black? If I disconnect them will it fix the code? I'm guessing it's just a signal for the electronic brakes. Thanksb
What error
@@FalconpevSg I think it's a brake sensor error. It's the (!) on top right of the display. The rear brake lights are flashing but there's no reaction when I press the throttle
@@assassin8r the brake sensor could be spoilt. Try removing the brake sensor?
@@FalconpevSg where is the brake sensor located?
5:48 "No complicated tools are needed". Apart from that special brake line plug insertion tool. 😂
That’s a regular brake item
Can it also use it to zero9?
Alex Komang yes it can
Where can I purchase this brake set in Europe ?
Andrea Ciuro only on our website
Hello, thanks a lot for making this video. I have the EMOVE cruiser electric scooter and need to swap the brakes from mechanical to hydraulic.
First, I want to know how well yours work in wet conditions.
Secondly, is there any place/physical workshop I can visit to have that installed?
Lastly, anybody to contact?
Thank you!
You can bring it to rev rides or try doing it yourself?
@@FalconpevSg
Thanks for replying. I am currently in Croydon (London). Do you mind if I ask for the address/location of Rev rides?
@@oliveraidoo7861 if London definitely recommend PET personal electric transport
@@FalconpevSg
Okay man, thanks a lot
Hi How to add front motor for 10X And what parts are needed?
Zero 10 or 10X? 10X already comes with front motor
@@FalconpevSg for Zero 10X
Will oil come out the cable when you cut it and then need re bleeding?
You must cut the cable and insert the olive pin
@@FalconpevSg will it fit the kugoo g-booster thanks
@@ElectricunicyclesUK don’t know what that is
What do do if my new hydraulic brakes are still noisy? I'm having hard times adjusting them.
What kind noise?
@@FalconpevSg the pad is rubbing on the rotor. I managed to tune the rear wheel, just releasing the screws and then holding the breaks while closing it again. For some reason I have some hard times doing the same thing in the front wheel
@@rbmanb new pads?
@@FalconpevSg yes. Okay! Done! Just had to release and and strengthen it twice more... But now no sound.
This nutt hydraulic brake comes as a front and rear set for the price ?
yes one set front and rear.
@@FalconpevSg Thanks 👍🏼
Hey everyone.
I put my zoom brakes back together but my brake lights are flashing and it won’t move.
Can anyone help me please.
Did you connect the ebrake wire properly?
@@FalconpevSg what is ebrake wire ?
@@declansmith1022 if you didn’t know what that is then there is something missing in your installation
@@FalconpevSg i put everything back the way it was before.
@@FalconpevSg do you have another way i can contact you and send photos please.
Can u actually respond to the damn instagram page???
you keep skipping parts
curious to know which part was unclear?
@@FalconpevSg connecting the brake cable to the lever, well i had to watch another video to realise that i didnt need to drive the needle head to cable, as mine was simply to put the olive in before connecting it. Also the removal of the original brake levers wasnt shown and were to cut it
@@TheSecretBaller so it isn’t skipping parts. We don’t show what you don’t need to do.
@@FalconpevSg I disagree, firstly cutting of the brake levers (e brake cable) is needed, which wasnt shown from the start. I thought there was a connection that i had to unplug and had no idea which wires to cut. Secondly the process of installing the new brake cable to the new levers is different (for the 10x) as no pin is need to be pushed in before insertion.
@@TheSecretBaller anyway if you look at the video it was taken more than a year or two years ago. Parts have been changed so some parts are outdated. But in general the concept is the same and that’s what we are trying to promote. A detailed tutorial is not what this is meant to be.
your comment is not correct. If rotor ( disk) is larger you need a new spacer, never use washers
We use Spacer washer interchangeably maybe not the correct term but the idea is the same