Novatec D791SB / Joytech Front Hub Overhaul. How To Remove The Cups.
Vložit
- čas přidán 1. 08. 2024
- Workshop tools and lubes: tidd.ly/d3e3cc04
0:00 how to find out, you have this hub model
4:41 you might want to see this part first
1:20 how to remove the busher (easy, but you need to know it)
1:55 bearing inspection
2:43 where are the o-rings
3:20 where I put the grease
4:05 installation
5:09 cleaning and degreasing - Jak na to + styl
3 years later and you just solved my problem in 1:38. HighFives all around!!
the LAST video I was going to look at answered my cap removal question in 10 seconds!! thank you! I kept skipping over it because I was searching Novatec!! thank you
My dude! Thank you... I was struggling with those cups all day. I just needed to give it more muscle.
the Union hubgenie is the best way, damages nothing and 20$ saves you a lot of struggle👌
Good video, you can service cartridge bearings when needed a little pick to pop seals, haven’t had to do it yet . Will last you longer between services than the cup n cone on your rear wheel.
Too thanks. You’re a champ for helping me
Gracias! No podía quitar los caps del hub delantero. Saludos desde Mexico
Thanks friend. I almost break orings until see your video
Great BB tool hack right there, thanks!
great video mate, cheers
Resolveu meu problema 👏👏
Good video.
The metal in the cap is pretty soft alloy, you will damage it with the corners of the screwdriver even if only very slightly, did mine today after watching this. Good explanation but
It is good to put grease there. Because if it is dry, the o ring could squeak which is annonying.
"Boosher." First, thanks for posting. Liked. I just got one of these, the dh61sb. Think I'll try a piece of wood to pry those puppies out. I sorta cringed at seeing that screwdriver do it. Happy landings!
This video said How to overhaul the hub. I thought it was going to show how to replace the seal bearings. Do you have one of those?
Don't you have a problem with friction between O-ring and the buschings? I do have and it is quite significant.
Наконец то хоть одно понятное видео как снять эти факинг колпачки
Плохой способ снятия колпачков это, лучше в строительном магазине подобрать монтажный анкер-цанга и им вытаскивать.
Please where do i find 20x110mm front wheel with Centerlock to buy ?
I have a Merida One-Sixty 600, model 2018
According to DT Swiss service procedures, the end cap should be put into vice with soft jaws and the whole wheel should then be pulled swiftly. This works without scratching anything.
Any chance youve found a video of this being done ? I have 641frobt hub and I feel like it's got the same system as above but no matter how hard I tweak on it it won't budge
@@farfrompkin yep. I followed this procedure and it works. The end cap was stuck tight so I had to pull fast to get it out. czcams.com/video/-Wde2goI3Cs/video.html
Sir do you have a disassemble of bearing?
Does anyone know if it's possible to convert this hub from standard to boost spacing?
Can you tell what the front bearing reference is?
Is there 792 service guide?
Thx for sharing your experience 👍
But the best way to remove bushers and end caps is to use a bearing puller 😉
Too much scratches with a screwdriver🙁
If you don't have a bearing puller, you could use a Dynabolt 👍
first, insert Dynabolt in the busher/end cap (not too deep in the bearing) and tight it.
Then, flip the wheel and insert a rod across the hub onto the Dynabolt and knock it with an hammer to remove Dynabolt with the busher/end cap.
You could use same technique to remove the bearings 😉
What kind of bearing puller?
Was hoping to see you remove and replace the cartridge bearings. Maybe next time would make a nice video?
Clive Weir this was tricky on the previous Novatec 771... there is a bush/spacer inside but it doesn’t push apart sideways far enough to get to the back of the bearings .. as I was replacing the bearings anyway I destroyed one to get it out.. the other was easy as I took out the spacer first.
What is a label on that joytech hub? Whats the code
Would you recommend these hubs? I was thinking of buying the DT Swiss 240S, but then I noticed the D791SB with similar weight to 240s, but a quarter of it's price
front is ok, rear better choose 240
makasih
👍🤝
How do I remove the bearings?
You need tool
How do you get the bearings out?
prolly need a bearing puller for it.
You need a 19,5 mm pipe , 200 mm long , split with a saw in half about 60 mm , opened circa 4 mm , and introduce from the opposite side in the bearing , you should be able to hammering out , it help if you have an electric hot air blower gun , heat the hub (the alu rotor) witch will expand in circumference and diameter ...
How you remove bearings?
Same way or from the other side with flat headder
You need a 19,5 mm pipe , 200 mm long , split with a saw in half about 60 mm , opened circa 4 mm , and introduce from the opposite side in the bearing , you should be able to hammering out , it help if you have an electric hot air blower gun , heat the hub (the alu rotor) witch will expand in circumference and diameter ...
Hola, por favor alguien me puede decir como extraer los rulemanes.
If anyone could tell me how to remove these bearings prior to me destroying them with a blunt instrument I'd be very grateful
You need a 19,5 mm pipe , 200 mm long , split with a saw in half about 60 mm , opened circa 4 mm , and introduce from the opposite side in the bearing , you should be able to hammering out , it help if you have an electric hot air blower gun , heat the hub (the alu rotor) witch will expand in circumference and diameter ...
Thank very much..semoga anda mendapatkan hidayah..amiiiin
What disk rotor do you have?
Shimano SLX
Shimano SLX I think
Shimano sm rt56 (deore i think) is a good rotor ? I want to buy
@@valentinsalcianu2702 It's decent
Thanks
Its same as novatec d881?
eso quiero saber porque tengo las 881-882
Worst design... Thank you for the video
где эти колечки под torque cap взять в россии? народ, поделитесь ссылкой может на алике есть?
Я тоже их хочу. Но не могу найти