How to Replace Ignition Switch Actuator 1993-1997 Ford Ranger
Vložit
- čas přidán 25. 08. 2024
- Buy Now!
New Ignition Switch Actuator from 1AAuto.com 1aau.to/ib/FDST...
This video shows you how to install a new ignition switch actuator on your 1993-1997 Ford Ranger. If the starter switch in your vehicle is not working properly, you will have trouble starting the engine!
This process should be similar on the following vehicles:
1993 Ford Ranger
1994 Ford Ranger
1995 Ford Ranger
1996 Ford Ranger
1997 Ford Ranger
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obeJ/1A...
• Phillips Head Screwdriver 1aau.to/obeJ/1A...
• 13mm Socket 1aau.to/obkk/1A...
• 8mm Socket 1aau.to/oa2S/1A...
• Trim Tool Set 1aau.to/o6f/1AX...
• Needle nose pliers 1aau.to/oBC/1AX...
• Needle nose pliers 1aau.to/oBC/1AX...
• Snap Ring Pliers
• 9/32 Inch Socket 1aau.to/obW/1AX...
• T25 Driver 1aau.to/oCS/1AX...
• T30 Socket
• Ratchet 1aau.to/obum/1A...
• Socket Driver
• Socket Extensions 1aau.to/obkk/1A...
• Gloves 1aau.to/oSQ/1AX...
• Marker / Writing Utensil
• Safety Glasses 1aau.to/oLa/1AX...
• Large C-Clamp
• Pick 1aau.to/oK5/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
All that for a plastic actuator. Who ever engineered that needs a good beating.
Thanks! Your way of taking us through replacing this actuator was so superb. No loud music, right to the point with good visual.
Thanks. Job well done. Great explanation. No loud music. I could understand. Every word.
THANK YOU!!! So I didn't have to take the steering column out because it was the 3 little parts in the ignition I was missing I didn't know existed. Saved the day with this video.
+Alisha Rettkowski Thanks for watching our video! 1aau.to/m/Shop-TRQ
One of the BEST DIY videos I’ve ever seen. Thank you
I have a 1996 ford ranger that thinks it is always on. You turn the key off and it won’t turn off. We replaced the ignition lock cylinder already. Is this what is broken with mine? I am thinking it is.
Great video,well done. the repair seems involved for the replacement if a small part.Ford should be sued if that is the easy way.No complaints about the video, but it leads one to realize there are couple places we could run into difficulty.
Finally getting to my own 1999 Ranger this Christmas. I really appreciate how long your video is and that you told what size sockets, etc. It will be nice to have my 369k mile truck back for those home depot trips. You did a terrific job with this video!!!!
Excellent video. Clear, concise and right to the point. Thank you!
Great video. I actually feel like I learned something.
How do you remove the ignition switch on a 1992 Ford f250 if you don't have the keys? That's what I was googling and it suggested this video. Watch first half of your email and you are very detailed like usual. But I'll see wasn't showing me what I needed. Understand that you turn the key to run position but that's the problem. Ignition switch in cuz I've lost them.
It seems like this would be the same/similar as the 2000 Ford Ranger Automatic ? With the shift lever being present, of course on the top of the column...
Is this the same column for a 98 mustang gt?
Loosk like yours only has one tilt lock on colum lock mine has two.can i get by with one
Good job posting this valuable information! I have been trying to replace all the same ignition parts for weeks without success.....but now after watching your video you've shown the way +!~♡~ 37:02
This is great but for an automatic there is a lot more to deal with. I did it but had some major problem solving to do.
Why did you change the actuator, what messes up on them? I would think the teeth but those teeth looked okay
Informative video! Thank you Sir
How did you remove the lower actuator? The big block piece that came out so easily when you removed the frame? My 95 grand marquis did not fall out like that.
Would i be able to use this video as a guide for my 2001 ranger
I have to replace that actuator on a 2003 Grand Marquis. With the key I can start the car, but not shut it off. I took things apart to get the switch part off. I can see that the part of the actuator that engages with the ignition switch is the part that does not slide up. The key turning can only push it down (towards the start position, but not bqck towards off position)
Mine won't turn into position to let the key out. Cylinder slot was missing the green piece and the metal plate when I took it apart
Is it necessary to remove the entire column from the vehicle? I saw a post on the CrownVic forums where someone removed the steering wheel, clock spring, airbag, and cylinder lock housing/tilt and was able to access the actuator rod that way, whilst leaving the bottom portion and steering shafts (with ignition switch and lower actuator block) in place.
The block that the rod connects to, how does that come out. i have tried a few times and there sees to be no way. Its "the plastic block" you talk about as you are pulling the two halves apart. its at 17:45
BTW. Great video. i am a fairly accomplished tech, but i have never done a steering column. so this was a great experience and with your nicely detailed and not overly non-subject yakky proceedure was refreshingly proffesional. thanks
What would be symptoms of why you would replace this acuator?
I have a 2000 Ford Taurus SVG Sedan that has an almost identical steering column. I turn my key and it will move to the start position, but won't go far enough to turn the engine over to start. I've removed my ignition switched and with the key in the lock cylinder, I can move the ignition switch manually to start the car. Can't figure out why my key won't turn far enough to move the switch post/pin far enough. Any ideas?
+@therobbywaller We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
WHATS THE SYMPTOMS OF THIS GOING BAD PLEASE
Awesome Teacher ☆☆☆☆☆
is there any danger of air bag deployment while doing this install? You don't mention it, but I wanted to make sure before I took on this project! Thanks
life saver
Can anyone say if this is the same for a Crown Vic or pretty much? I can't shut mine down. I can start it with the key but I have to suffocate it and pull the battery terminal to shut it down. The key just spins around if I turn it backwards.
you should try taking one apart without marking anything. the actuator rod will only install one way .
an overall present experience to fuel contempt for the building 5 folks at Ford.
Good vedio, but he doesn't answer many questions. So many questions are not being answered.
So how much would a repair shop charge for this job?
you didn't re install the security clip deal with the black wire>>>> why was that?? thx, :) Mark
is the removal and install the same for a 2000 f350 super duty?
+Emma Dana This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
Where's the shifter tube at?
so at 17 minutes and 45 seconds the white block just slides out of the metal housing, but on an automatic Ranger there's a catch that prevents that block from sliding out. what do I do?
Do you have a video for doing this on an automatic transmission?
Please never record the audio that close to your mouth again