I chased a No Brake Lights and an illuminated Stability Control light problem through this whole system of fuses, switches, relays and wiring. After checking the components from the Fuse to the Hill Assist relay I determined the Hill assist relay was not allowing the signal/power to go to the brake lights. I replaced the Hill Assist Relay in the fuse box under the hood and The brake lights work and the Stability Control Light has gone out. Thank you for such an in depth look at the brake light system. Without knowing the brake light relay output went to the hill assist relay before going to the brake lights i may have had to take this car to an electrical shop to have them find the problem. Mike @ Phelps Body Shop of New Albany.
The relay not fuse is abbreviated HAC. I had the same issue with the traction control light on and no brake lights. I took out the HAC relay. I flicked it with my fingers a couple times, put it back in and the traction control light went out and I had brake lights again! Thanks Michael Phelps and Maic!!
@@massimodalessandro9259 both of you are blessings. I have a 2012 Optima SX-T GDI and for the past several months I’ve been chasing the issue with this stability light and how it would cause my brake lights not to work. Located the HAC relay, took it out flicked it, made sure it was clean, put it back in, and I swear it was like magic. Brake lights work and stability control light GONE. I have you two in this comment section and Maic to thank. Thank you
Very informational video. Kia is a good priced vehicle but junk wiring. Which Autel model did you use for this video? I have been looking into them but don't know which model is capable of doing all of this type of diagnosing.
Maic thanks for sharing. This was a good one. Maybe message me if the new assembly fixed the problem. Definitely a strange one. I’m sure the assembly wasn’t cheap. Pico seems a little more technician friendly. Stay safe and well Maic Artie 👍
I think this is better, it has a lot of software test that otherwise you 'll need to try and do with math channels. Pico is a much better scope as far as resolution and buffer, but for the daily test I do, cam - crank correlation, coil tests and so, ATS is a much faster set up.
Brilliant video tutorial outstanding love it ,Maic Salazar Diagnostics My Mentor 👍 INTVITIVE, Maic Salazar Diagnostics Take care and God bless you, Maic Salazar Diagnostics From Nick Ayivor from London England UK 🇬🇧 ⏰️ 22:07PM Good Evening
I have C2130 DTC - drive cycle check incomplete/pending. Brake lights work when pressing pedal and also when unlocking the car using FOB What could be the issue ? 2013 Kiia optima manual LX
Question? I have a 2011 Sorento brake light are dim and when I turn headlights on I have zero brake lights and it kills the throttle. I can let off throttle then back into throttle and it does fine only no brake lights!! Any suggestions?
Awesome video. I’m sure you know but i can’t help myself. You can just hit the invert button on the left of the screen instead of turning the amp clamp each time. Sorry lol
In the video description could you say @michaelphelps5064 has a comment with the solution otherwise people may watch to video and not check the comments, not knowing the answer is right here. Great video btw
I chased a No Brake Lights and an illuminated Stability Control light problem through this whole system of fuses, switches, relays and wiring. After checking the components from the Fuse to the Hill Assist relay I determined the Hill assist relay was not allowing the signal/power to go to the brake lights. I replaced the Hill Assist Relay in the fuse box under the hood and The brake lights work and the Stability Control Light has gone out. Thank you for such an in depth look at the brake light system. Without knowing the brake light relay output went to the hill assist relay before going to the brake lights
i may have had to take this car to an electrical shop to have them find the problem. Mike @ Phelps Body Shop of New Albany.
I am so happy to be of help. Blessings
What is hill assist relay
The relay not fuse is abbreviated HAC. I had the same issue with the traction control light on and no brake lights. I took out the HAC relay. I flicked it with my fingers a couple times, put it back in and the traction control light went out and I had brake lights again! Thanks Michael Phelps and Maic!!
@@massimodalessandro9259 both of you are blessings. I have a 2012 Optima SX-T GDI and for the past several months I’ve been chasing the issue with this stability light and how it would cause my brake lights not to work. Located the HAC relay, took it out flicked it, made sure it was clean, put it back in, and I swear it was like magic. Brake lights work and stability control light GONE. I have you two in this comment section and Maic to thank. Thank you
This comment needs to be pinned
Interesting case study Maic! Love the follow through of trying to pin point the issue! Thanks for sharing! & Congratulations on getting the Escope!!!
I wonder how that would look on a thermal image camera. Great diagnosis!
Thank you for the video man
Very informational video. Kia is a good priced vehicle but junk wiring.
Which Autel model did you use for this video? I have been looking into them but don't know which model is capable of doing all of this type of diagnosing.
Moving the ampclamp to the taillamp would prove it right away.
Good find.
Maic thanks for sharing. This was a good one. Maybe message me if the new assembly fixed the problem. Definitely a strange one. I’m sure the assembly wasn’t cheap. Pico seems a little more technician friendly. Stay safe and well Maic Artie 👍
Nice one Maic. 👍
Maic, AWESOME diagnoses thanks for sharing and is that scope easy to learn or PICO is better.
I think this is better, it has a lot of software test that otherwise you 'll need to try and do with math channels. Pico is a much better scope as far as resolution and buffer, but for the daily test I do, cam - crank correlation, coil tests and so, ATS is a much faster set up.
Saludos desde mexico 🇲🇽🇲🇽
Brilliant video tutorial outstanding love it ,Maic Salazar Diagnostics
My Mentor
👍
INTVITIVE, Maic Salazar Diagnostics
Take care and God bless you, Maic Salazar Diagnostics
From Nick Ayivor from London England UK 🇬🇧 ⏰️ 22:07PM Good Evening
Gracias bro
I keep getting distracted by the sign on the side of the car!
I have C2130 DTC - drive cycle check incomplete/pending. Brake lights work when pressing pedal and also when unlocking the car using FOB
What could be the issue ? 2013 Kiia optima manual LX
Sometimes it doesn't make sense that there's a problem in such a small harness but i've seen it many times mostly on chevy, n dodge.
Question? I have a 2011 Sorento brake light are dim and when I turn headlights on I have zero brake lights and it kills the throttle. I can let off throttle then back into throttle and it does fine only no brake lights!! Any suggestions?
Traction control and hill assist both come on shortly after lights are turn on!
Ughhh! I’m experiencing this with my 2013 Kia Optima. Stability light is on and no brake lights!! 😩
Having the same problems. Did you get yours figured out?
@@danielmaynard6127any update?
👍🏻👍🏻
Awesome video. I’m sure you know but i can’t help myself. You can just hit the invert button on the left of the screen instead of turning the amp clamp each time.
Sorry lol
you are looking at the wrong diagram you needed tf diagram not qf
Krap kar
ADHD....lol
The magnetic sign on door of car...
I think it's contagious....
You got it now...
Put YOUR bulb in their harness
In the video description could you say @michaelphelps5064 has a comment with the solution otherwise people may watch to video and not check the comments, not knowing the answer is right here. Great video btw