Tube Bending Simplified
Vložit
- čas přidán 2. 04. 2011
- The information in this book will benefit anyone who lays out and/or bends conduit, pipe, or tube. Everyone who purchases a copy of the book TUBE BENDING SIMPLIFIED , will easily and quickly become a master at tube bending and pipe layout.
This book is patterned after a comic book, so that it is easily understood by everyone.
It is an easy 2-hour read, and contains many tips and tricks that will benefit everyone from the professional to the novice, whether you are bending tube or laying out pipe.
In the USA, this book can be purchased by credit card through Amazon.com or through E-bay.com. Books can also be ordered by sending a check, money order, or Western Union to: Tube Bending 1483 Cardinal Lane Green Bay, Wi. 54313. - Jak na to + styl
Good morning Todd. Just wanted to drop you a line and tell you that I have used your method of tube bending layout and it has helped me enormously . I was on a job in Pennsylvania on a cracker and when they asked for tubing guys. I had no problem stepping up to the challenge. Guys have watched as I measured and layed out bends asking where I learned this. I'm helping our fellow brothers become better tubers, tell them to watch your videos and purchase your book to reference. It has been the best money I have spent to further my skills as a UNION PIPEFITTER.
Thanks for being a true union brother, and sharing your knowledge by writing this book.
Mike THOLL 597 Chicago, IL
Mr. Weiler,
Here are some pictures of the 1/2" SS tubing 1 1/2"radius that I bent using your book instructions that you so graciously assisted me with on phone conversation today. I cannot thank you enough. Your directions and explanations are dead on! The knowledge, skill and dedication you express in your craft astounds me! I learned so much from your CZcams video. I am amazed at the phenomenal results achieved so easily when I followed your explicit instructions. "Tube Bending Simplified" in my opinion, should be required reading in any shop class. Not only for obvious reasons but more importantly the discipline it will instill to follow and apply procedure in any job endeavor. Once again, a big THANK YOU for sharing, so affordably, perfect techniques in this otherwise tumultuous craft.
Warmest Regards,
Robert J Sigsworth
Reading your book has put tube bending into perspective. I have been to 3 different locations on a ongoing project and all of our customers have been in awe and cant believe how beautiful the work we have done looks. Thank you for putting this book together for others to learn from.Regards,Robert F. Doane
Great book - I have been bending steel for years with mixed results. I finally got serious about bending tubing when I got involved in a project that needed many versions of a prototype that used tubing as a frame. Todd Weiler's book of instructions made the process of layout and actual bending completely understandable. I'm sorry I waited so long. Great book and highly recommended.
Todd, Thanks for getting my buddy and I straightened out over the phone. It all makes sense after talking with you about how the tube spoon is laid out and used to mark the tubing on the bench. I was surprised to have you call me after I emailed you so quickly, that shows what an outstanding person you are and that you stand behind what you teach others. We are going to give it a try and let you know how it pans out for us. Thanks for ALL your help!
Joe Marsan isn't Mr. Weiler awesome!!!?? He called ME!! Just to assist in my bending. Such a generous man and finely tuned to his craft. I LOVE bending tube. AND I get PAID!!! Win win!!
John
I do not have an EFT account. I would prefer that all orders to individuals in foreign countries are paid by money order, organizations/companies may pay using a company check. This is a soft cover book, it measurers 5 1/2" x 4 1/4", it is 81 pages and with packaging it weighs 3.2 ounces to mail. The information is priceless! Thank you for your patience! Todd
Hi !Aside from this being a valuable book for pipe fitters, Mr.Weiler was also very helpful over the phone regarding the " Tube Bending Simplified" book.
Thanks again,Ron M.
He is so thorough that he even said ‘right’ instead of left, he took account the perspective of the viewer.
Just got off the phone with this man super helpful thank you so much!
Hi Todd, Got the book 5 days ago and I have been reading through the pages.
It's definitely worth the money - I think you are under selling it. If ever someone has been wanting to learn how to bend copper pipe they should read your book. I have been looking for a book like yours for ages, no guesswork just exact science and simple instructions. Cheers mate, John
Got the workbook and it is great! Really helpful. Will reside in my toolbox for years to come.
Just wanted to say thanks. You're little book changed my life 3 years ago I got a new job and there was some bending to be done wasn't too sure how to do it so that night I watched this video and ordered your book. Now I'm a foreman I don't bend much tubing but when I do it comes out great. It was just that one extra talent the other guys didn't have that set me apart.
Thank you!
If you ever have a tube bending, or a pipe layout question contact me.
You will find both my personal phone number, and my email address on the back inside flap of every book.
Hard to say enough good things about the contents of the book, the video or the author - simple expert views on how to bend tubing with a willingness to go a step further for those of us with problems absorbing - money well spent...
Jim:Thank you for your years of U.A. service, you were probably an excellent tube bender! Our U.A. constantly stresses training, so that all U.A. personnel are always capable, and can always "do it right the first time".In addition to this main video, there are supplementary videos on this website, which will help anyone to become better at bending tube. None of us learned that which we know (which other people do not know) overnight. The people who are the best at anything; are those people who are constantly learning, putting what they learn into practice, and then becoming as good as they can be in some aspect of their daily life!One of those supplementary videos shows a perfect 5 pointed star; which can be laid out, marked, and bent in less than 1/2 hour (10 bends - 1 piece of tube). That star can then be duplicated precisely, 1 or 100 times. All bends and all dimensions for all stars will be identical.Information in this book, reveals the easy formula to be able to cut any tube to within 1/16" of needed length, before starting any of the bends for any project.Another video demonstrates a coat hanger which can be laid out, marked, and bent in less than 1/2 hour (5 bends - 1 piece of tube). That coat hanger can then be duplicated with precision as many times as you would like. Each coat hanger will be an exact clone of the original coat hanger.I did not make a video to show how to layout, mark, and bend a perfect square (14 bends - 1 piece of tube); but I have laid out, marked and bent a perfect 3" square in less than 3 hours. I used a 9/16" radius tube bender, along with 39-12/16" of 1/4" O.D. tube. After laying the cube out, the tube was marked; then as soon as each bend was bent, getting the bender repositioned to be able to make each succeeding bend was the part which took the most time. The smaller the cube is, the more difficult the tube is to bend; because when bends are close together it becomes increasingly harder to reposition the tube bender between bends!In less than 2 hours, this book can easily be read, during which time anyone will learn the basics of how to become a good tube bender. This book will then assist everyone, throughout their entire career; either with tube bending, or with pipe layout. This book is written in such a way that it can be easily referred to on a daily basis; its' compact size (4-1/2" wide x 5-1/2" high), makes it easy to carry in a rear pants pocket to be readily available whenever the need arises.To be able to contact me at any time with a question related to tube bending, or pipe layout; each and every person will find both my phone number, and my email address in each book.
Thank you for the input!
I don't know about digital editions, but I do know that looking something up on a computer is not as convienent as having the knowledge you need at your fingertips.
The most recent printing of this book was in Sept. of 2015. It is now 81 pages of pure gold and is small enough to fit in a back pocket.
With increased printing and mailing costs a single copy is now $18.00.
This is the best tool, and the least expensive tool that you will ever have in your toolbox!
This book thoroughly explains a simple step by step method to bend tube without the use of a complex calculator. The teachings here challenge the SAG Method and clarify the craft of tube bending. A must have for any serious precision tube bender!
I like it, have you consider actually doing the bends, showing close ups of the marks and bender to give a more thorough visual description. I believe it will be helpful for those who are visual and hands on learners.
Recently I received an email which included the following statement: " By watching your FREE videos, I have learned all that I need to, to become a good tube bender! What good is your book?" Employers want qualified, knowledgeable employees. To get ahead, each of us should learn something new each day. This inexpensive Tube Bending Simplified book contains a lot of information which is not found in the videos. The more anyone knows, the more successful they will be. By using this book, not only will you make your employer money; each pipefitter or tube bender will become more valuable on every job, and each person will make thousands of extra dollars in future employment.
Harry: Thank you for the comment! I have tried many different rewrites of this book. I am always attempting to make this tube bending book easy for everyone to read and to understand! Just like any Haynes Auto Repair manual, all aspects of tube bending can not be explained using a simple step by step procedure. Writing an understandable book to teach someone anything, when the reader is miles away from the writer, is a complicated task. I welcome all suggestions for changing this book to make tube bending easier for both the novice tube bender and the accomplished tube bender!
Dick:
The bend radius charts (28 of them) which are explained with crystal clarity on pages 11, 12, and 13 in this book were developed for use with SAE radius benders.
Since math is constant throughout the world; the 2 formulas on page 7 will work exactly the same weather you are bending SAE or Metric tube, no size conversion is necessary. I just have not developed any individual metric charts.
1 English pound is equal to about 1.5 U.S. dollars. The rate varies daily.
Todd
Numerous people, who have purchased a copy of this book, have contacted me suggesting that I incorporate changes into future printings.
This is the easiest bending book to understand and it explains the best way to do any manual/hydraulic bending.
Please contact me with your suggestions as to how to improve this book.
Thank you!
such a nice guy...
Is there any chance you have a digital version of this book that I could purchase?
Eddy:
Thank you for the comment! I should have replied to you sooner, but my computer caught a nasty virus and I could not reply to anyone until today. Yes, 8/16ths is also known as 1/2, but measuring to the nearest 1/16th of an inch is 8 times as precise as measuring to the nearest 1/2 inch. Whenever tube is being properly bent, the act of measuring precisely is the difference between doing an easy, professional looking job; or struggling and hoping to get the job done. Todd
A chalkboard / whiteboard teaching I think would be very helpful.
As I am a bit unsure on trying to tie it togethers from your analogy.
Perhaps when I do a few exercises with it will clear it up.
thx
Order a copy of the book, read the book; and then view the video Tube Bending While Using A Tubespoon Marker. As soon as you understand this method of tube bending, you will without a doubt become one of the best pipe fitters or tube benders on any job! If you ever have any tube bending or pipe layout related question, you will always be able to e-mail or call me!
@@t04041951
Knowledge is POWER.
Thx
Dick:
On page 39, in this book; there is a very simple conversion formula to convert inches to millimeters and vice versa.
In the video (from 9:17 to 9:29) an ordering address is included, along with basic handling charges. After having checked with the local Post Office; due to custom duties, regulations, and paperwork mailing cost to any international address is $15.00. Any shipment within the 50 U.S.A. states is $4.00. Every book shipment will include tracking within the U.S.A., so be certain to include an email address or a contact # with each order.
I would like all payments to be made in U.S. dollars
Thank you Todd
Home shop machinist here and would love to learn how to bend tube like a pro. My first question is: Do I need the fancy Swagelok bender brand tool or can I go the cheaper route and use a Rigid tube bender? 2nd question, where’s a good place to buy tube and what alloys? Is this for stainless only? 3rd, What is the standard wall thickness?
Thanks for your help. Headed to Amazon to order your book.
For any tube bending or pipe layout questions, call 920-264-6440, or email: tweiler1@new.rr.com
Both this phone number and email address will be found on the back inside flap of every book.
You will become a great tube bender after having read this book.
It will take most people about 2 hours to read, and to understand.
BikerTrashWolf:
Math is constant,the basics of which never change!
The information in this book can easily and precisely be used by anyone who is using either a manual or a hydraulic bender.
On page 7, in this book, 2 simple formulas are explained so that anyone can construct a tube spoon marker (explanation on page 15).
A tube spoon marker is necessary so that all bends will be uniformly bent.
(continue in next reply)
Todd
BikerTrashWolf:
It makes no difference whether you are bending 3/8" tube or 38" pipe; so yes, it is simple to make any degree bend using 2" tube with a 5.5" radius.
If you ever have a bending question, my personal e-mail address is included with every book order.
You will never regret owning a copy of this book!
Todd
When it comes to the 45 degree bends. When I move the cl to the a.c. mark. I can't add a ref. line because the T.C. line would be the ref line . Is that correct with the tube marker? If so, do I just measure from the cl to the next cl is the next bend would be another 45 bend?
You are correct.
For any bend angle where the T.O. dimension equals exactly 2 times the A.C. dimension, your reference mark on the bend will be the same as the centerline mark.
Math will always be constant.
This rule will work with any bend angle, for any radius bender.
On 01/03/19 I have uploaded a new 13 part 26:48 minute video to youtube. It is called Tube Bending While Using A Tubespoon Marker. Watch the 13 parts at your leisure! After learning how to properly use a tubespoon marker, along with following the instructions in the book Tube Bending Simplified; you will become one of the best tube benders on any tube bending job.
When making a tube spoon marker do I mark the to and ac on the paper from center line?
Figure #1 in your book will show you a visual representation of the logical progression, of how to construct every tubespoon marker.
If you ever have any tube bending question that you need answered, both my email address and my phone number which can be found on the back inside flap of every book are:
tweiler1@new.rr.com
920-264-6440
Where can I find tables or equations for bending radius for round and square tubes (steel and aluminium)? Thank you.
On pages 11-13 in this book, there are 28 individual bend radius charts which show the dimensions needed for the 7 most commonly used bends; using any material, with any bend radius bender.Any degree of bend, for any radius bender which is not listed in the 28 individual charts, may be easily calculated by using the 2 simple formulas on page 7, along with the tangent of the angle; which will be found in the Trigonometry tables, which are presented on pages 45-47 in the book.The latest printing of this book is the 8th printing. This is an easy to understand, self-teaching guide, which can be read and understood by many people in less than 2 hours. If a bending or a lay-out question does arise which the reader can not understand the answer to; anyone can email the address, or phone the number; both of which will be found on the inside back flap of each book. Emails are replied to within 24 hours, 7 days a week. Phone calls are answered 8 AM to 8 PM CST, 7 days a week.Purchase yourself a copy of this book, there is a money back guarantee on single copy purchases!
I have a question for you, do you know where the number 0.01745 comes from? In relation to the equations for determining the advance of a bend. I know it is a constant number I just wonder where the number came from.
This is a very good question. On page 7, in the Tube Bending Simplified book, line 18 reads: 0.01745 is the tangent of 1 degree. The answer to this question can also be found in the Trigonometric Tables on page 45 where 1 degree and the tangent coefficient intersect. For the purposes of constructing the tables in this book, this number was rounded to 0.0175 If anyone ever has any question related to tube bending, do not hesitate to contact me, both my phone number and my email address can be found on the back inside cover flap of the book.
Every Tube Bending Simplified book which is mailed out, is personally mailed out by me, Todd Weiler, the author of the book.
On the back inside flap of every book, both my contact phone number and my email address, will be found. These should be used by anyone, at any time, with any tube bending or pipe layout question.
If ever, you have a question about anything in your book Tube Bending Simplified; please send me your book order number, along with the approximate date your book was ordered, your name, and your phone number.
All emails will be responded to within 24 hours.
In April 2022; due to inflation which is affecting both the printing cost of this book, and the postage to mail out this book, the price of each of these books has increased from $23.99 to $25.99.
Could this be used for larger materials? About to start building a roll cage and need to figure up for 2" tubing on a 5.5" clr die.
how to buy your book, i tried to buy it ,for example, amazone, may be it out of print, please help me order your book on amazone
김경기 Hello. You CANNOT go wrong with this book!! I've bent a lot of tubing and Mr. Weiler is the tube GOD!!!!
Are these books still available and is the price still accurate and current?Thank you Gregg
Greg: These books are still available from: Tube Bending 1483 Cardinal Lane Green Bay, Wi. 54313 The cost per book is $18.00 plus the S&H (shipping and handling) rate within the 50 U.S.A. states is $4.00 per individual book, each additional book will be an additional $1.00 for S&H. Include an email address with each order; so as to relay a tracking number back to you.
Hello! My name is Joan Peter Willen. I am interested in this book. Can you deliver it to Sweden? If so how can I pay?
Joan: Yes, this book can be sent to Sweden! The cost of each book is $18.00 Due to customs forms, and paperwork; every international S&H (shipping and handling) rate is $15.00 per individual book, each additional book will be an additional $5.00 for S&H. All S&H rates include tracking during U.S.A. travel. Include an email address with each order so as to relay tracking information back to you. Books can be ordered from: Tube Bending 1483 Cardinal Lane Green Bay, Wi. 54313 For the quickest delivery of this book, order through Western Union converting to U.S.A. funds. Thank you for your interest in the knowledge which you will learn through this book.
Definitely interested in this little book..but I'd love to see a digital edition (paperbacks don't survive long in my tool box). Also is it available on Amazon yet?? If not, there's a large market for you to tap.
Is your book on Amazon now?
As of 06-20-2013 this book is available on Amazon.com for anyone who would prefer to use a credit card to make a purchase.
In plain language; this book will precisely explain to anyone the simplest way to layout and mark any length of conduit, tube, or pipe before bending it.
No guesswork will be involved in the process of making any bend.
No layout or bend (S.A.E. or Metric) will be too difficult to bend.
All bends will look professionally bent.
Simply the best, better than all the rest!
Hi. Can you deliver Finland ? I want to buy that book..
Jani: Yes, this book can be sent to Finland! The cost of each book is $18.00 Due to customs forms, and paperwork; every international S&H (shipping & handling) rate is $15.00 per individual book, each additional book will be an additional $5.00 for S&H. All S&H rates include tracking during U.S.A. travel. Include an email address with each order, so as to relay tracking information back to you. Books can be ordered from: Tube Bending 1483 Cardinal Lane Green Bay, Wi. 54313 For the quickest delivery of this book, order through Western Union converting to U.S.A. funds. Thank you for your interest in the knowledge which you will learn through this book.
A few pipefitters have informed me that the knowledge in this book should not be available to anyone who does not belong to the union.
I believe that anyone who needs to learn or wants to learn, so that they may advance in their position in life; should have the opportunity to do so.
Also; anyone can acquire the information in this book either by reading numerous related books at various libraries along with 100's of hours of computer research, or through buying this book and learning on their own in a few hours.
Ramirez:
Answers to questions about bending will become crystal clear once you get a copy of this book; but if you should happen to not understand any portion of the book, always feel free to e-mail my personal e-mail account (included with the book) in regards to any questions/comments.
Thank you!
Todd
I’ve got the book, I’m watching the video and still have not a clue what at tube spoon is. Sorry feller, my mind and your instructions are not in the same room.
Hi Rowdy Flyer1903, my phone number and email address are in the back of the book. Please reach out and I'll be happy to assist you.
why do you put 3 marks on a piece of tubing?all you need to do is figure how much you gain and take it out for each bend.
3 marks are marked onto the tube at each bend, so that the person who is doing the bending will know exactly where to place the bender prior to each bend, so each bend can be bent precisely. Further, by placing 3 marks at each bend prior to doing any bending, an entire length of tube with varying degree bends can be laid out, and all bends can be marked with precision, before even 1 bend is bent. Each bend can be bent as either a left hand bend, or a right hand bend. All bends will start by placing the bender at 1 outside mark, bending over the centerline mark, and the bend will stop at the 3rd mark. This method will work for any degree of bend up to and including 180 degrees. Most of the time, it will be easiest to bend each bend in the same progression as it was laid out on the tube. Occasionally, as in the case of a wall penetration, the 6th bend may need to be bent first. The other 9 or more bends can then be bent in any practical order. Each bend must be systematically laid out onto the tube in the proper succession to attain the greatest degree of bending accuracy. All bends, center to center, can be marked and bent to tolerances of less than 3/100". Multiple identical tubes can easily be bent by using this bending layout method!
you are not showing the simple way to bend tubing........all you need is one mark as your center line burn your gain and mark next centerline and so on until you finish laying out your tube. ive bent miles and miles of tubing and never had to use three marks.
In my youth; I was taught that the only way to bend tube was by using the measure, mark, bend method. At that time: I should have been a logger, I bent a lot of expensive tube into worthless firewood! There had to be a better way! In common language, this book explains an easier, more exacting method of tube bending. As an example; what if you need to bend a 9 degree bend, and keep the center of that bend perfectly on center? This book explains how to do that while making the bend look like it always belonged in that place, not as though someone accidentally stepped on the tube. As long as you are happy with your tube bending ability, that is important. Being proficient, by using this method of tube bending is simply another tool in your toolbox of knowledge to help to keep you gainfully employed. If you ever have a tube bending question, email tweiler1@new.rr.com or call 920-264-6440. I will be happy to help you to make all of your bends look as though they were bent by the most qualified professional bender.
Using 1 line there’s a chance you’ll get lost in bends plus you would have to work left to right. 3 lines insures where the bend is and which way it goes. If you went to break and came back it’s easy to accidentally bend the wrong way. With 3 it doesn’t matter which bend you do first. The 1 line is just skipping steps in 3 line. You could also use 2 lines. It’s a personal preference which you use but to insure no mistakes the 3 line method is fool proof
For a fast response to any question about this book, or any tube bending question; the following email is checked 2-3 times daily tweiler1@new.rr.com
CZcams can/does edit/delete responses over 500 characters in length.
Dear Sir,I try to order that book,But Amazon tell them me ,you cannot ship to Taiwan,Could you tell me how to do?
Dear Sir,My email address is fengyingtse@gmail.com
and tell me how to pay this Monday.
I asked your book to the manager at KYBO BOOK STORE one of biggest book store in Seoul, Korea. but as the result, he said to me it may be out of print. i can do transfer wire to your account...
Dear Sir/Mam: Amazon.com will not ship many items outside the boundaries of the U.S.A. I WILL MAIL this book to anywhere in the world!
The cost of each book is $18.00 Due to customs forms, and paperwork; every international S&H (shipping and handling) rate is $15.00 per individual book. Each additional book will be $18.00 plus $5.00 for S&H in the same mailing package. All S&H rates include tracking during U.S.A. travel. Include an email address with each order so as to relay tracking information back to you.
Books can be ordered from: Tube Bending 1483 Cardinal Lane Green Bay, Wi. 54313 For the quickest delivery of this book, order through Western Union, and convert to U.S.A. funds.
This book is written in English, and I speak and read only English. Thank you for your interest in the knowledge which you will learn through this book.
My email address is tweiler1@new.rr.com
thank you. i would go to bank, transfer by wire.
Hi great video, I live in Australia and would like to purchase a copy of your book, could you please advise if you have an EFT (Electronic Funds Transfer ) account that I can transfer funds directly into, it will also do the money conversion for me.
Also do you have a soft copy of the book
Cheers
John
Dear Sir,May I use this for mm?
The information from this book will work precisely, regardless of whether metric or S.A.E benders are being used.
I am understanding that the tube which you are bending is 6mm O.D. tube.
Page 10 in the book explains that for layout purposes, it is more important to know the radius of the bender which will be used to make any bend, than it is to know the diameter of the tube which is being bent.
On page 39 in this book, there is an easy to understand explanation for conversion from millimeters to inches, or vice versa. Neither millimeters nor inches can be used with the 2 formulas on page 7 until that dimension is converted into its’ decimal representation.
After the decimal representation is calculated, use the 2 formulas on page 7 to calculate the T.O. and A.C. dimensional marks which you will need for precise tube layout.
An explanation as to how to place the marks onto the tube is given on page 6.
An explanation of a tubespoon marker is given on page 15.
Both a contact email and phone number are included with each book to answer any tube bending questions.
In the near future; I am planning to make a hands on visual learning video, to help everyone to better understand how to make a tubespoon marker to assist in bending tube. In addition to other benefits; a properly made tubespoon marker will assist in marking every bend, so that every bend will be bent to the precise degree needed!
I would really appreciate the visual video, I believe it will assist a lot of people. I'm an Instrument Tech/Fitter and your book and video are talked about in this industry. I bought your book and applaud you for what you do to help others excel. You're leaving behind a legacy, again thank you.
Wouldn't 22 8/16" be 22 1/2"?
+Michael Healy Mike, this is a good point. 8/16" is the same as 1/2", but 8/16 is 8 times as precise as 1/2. When tube is being marked, being precise is very important. Imagine for a moment that you are going to meet someone in an unfamiliar part of town, on a street, anywhere in the U.S.. Further, imagine that you find 16 houses on one side of the street, when you get to where you are going. It will be easier, quicker, and more precise to arrive at the correct house, if you are told to meet at the 8th house rather than 1/2 way down the street.
Todd Weiler If you find yourself coming on to 16 houses you should know that halfway would be eight houses!
tube sha doobie doobie
JM By the time the whole process was explained, i could have had two pcs. bent using the measure to bend method with one cut, and less chance of error, with less marks and more accurate. I happen to be a retired UA pipefitter.
Amen brother.....tittle says bending simplified..should been called Bending Over complicated
It appears to be both an accurate, and efficient method to bend tube, and once fully realized, may indeed be simple.
Headlining the title, the term "simple" seems to be used a bit loosely, and excessive in this video, particularly in light of the fact that this brief attempt to explain, express, or convey as much, frankly only served to confuse me.
While the general tone of dialog as read by the speaker seemed to suggest a sense of ease and simplicity from his perspective, I found it a bit annoying having little to no relative understanding of terms such as "takeoff mark", or "arc mark", without having referenced the pages of the book, stated in the video that apparently explain them.
Budda:
You are very articulate and your curiosity has been aroused. No-one can learn to become the best at anything through any short informational video. This video appeals to the curiosity of those who need or want questions answered to help them to become the best tube bender that they know.
All I ask you to do is to order a copy of this book, the cost is only $14.00 plus shipping. For future questions, both my personal email address and my personal phone number are included with each book.
This is the best book which you will ever find to teach yourself how to bend tube.
After you have read this book most of your questions will have been answered, and you will have become a great tube bender. Through this book, for future reference, all of the information that you will need to do any bending will be at your fingertips!
This video is totally worthless,because you didn’t do a close up view of the tool that you had in your hand,so the setting wasn’t wasn’t visible to learn!