Restoration & Repair of broken Xbox 360 and Fix The Red Ring of Death - ASMR
Vložit
- čas přidán 15. 09. 2021
- -----------------------------------------------------------------------------------------------------------------------------------------------
Restoring the Original Xbox 360 Controller
• Restoring the Original...
-----------------------------------------------------------------------------------------------------------------------------------------------
In this video, I repair an Xbox 360 that suffers from the infamous Red Ring of Death (RROD). While this is a well-documented issue I was surprised at the lack of quality repair tutorials targeting DIYers. Most "reflow" videos are silly hacks (like wrapping your Xbox 360 in a towel) and even tutorials that suggest using a heat gun leaves a lot to be desired. For example, I didn't
I think there can be a version of an at-home RROD repair that uses simple tools that anyone can follow, resulting in a permanent fix.
To repair the red ring of death I used a heat gun according to Ifixit.com I set it up to 400 degrees Celsius. I'm starting by warming up the back of the motherboard for about one minute.
The chips can be damaged by heat also so it's important to move the heat gun around. three inches away from the board the constant motion at this distance isn't going to melt anything on this large of a surface area.
You should avoid the capacitors so that they don't get any direct heat.
After the initial warm-up, I applied flux which will help the reflow of the solder joints.
Unfortunately, I did not install the CPU heat sink correctly, I realized this mistake later after I finished the video so I corrected it after the video
This video shows you everything you need to know about taking apart your Xbox 360. If you need to replace the fan or the disk drive this video will show you how to get inside and disassemble your system. Since this system isn't the newest on the market anymore, it's cheaper to replace the parts yourself than it is to send them in for repairs.
Restoring the Original Xbox 360 Controller - Retro Console Restoration & Repair - ASMR
Leave any questions in the comments, and don't forget to LIKE and SUBSCRIBE!
Thank you for watching.
Junk PSP Restoration - Sony Playstation Portable 1000
Microsoft Xbox 360
amzn.to/2XzbPFr
Some of my tools:
Screwdriver:
amzn.to/3hPBOiC
Isopropyl Alcohol 99.9% Electronics Cleaner:
amzn.to/2XvnTHl
Hot Air Gun Kit:
amzn.to/3lJ2SkG
My main camera:
amzn.to/2XHl6er
UV LED Strip Lights
amzn.to/3kXhSMU
Black gloves:
amzn.to/3zo0ZyQ
--------------------------------------------------------------------
Restoring the Original Xbox (CPU overheating) • Restoring the Original...
--------------------------------------------------------------------
Restoring the PlayStation 2 Slim • Restoring the PlayStat...
--------------------------------------------------------------------
T-Shirts (support me)
restorationeg.myspreadshop.com/
--------------------------------------------------------------------
All you have to do is join this channel to take advantage of the benefits:
/ @reseg
--------------------------------------------------------------------
#restoration
#repair
#gaming
#asmr
#xbox
#broken_xbox
#The_Red_Ring_of_Death
#relaxation_asmr_videos
I love seeing these consoles get another chance at life. It warms my heart
@Roblox Gaming10 I see what u mean lol
same lol
Finally a person who follows the same emotions as me, I feel you 100% bro you always give an xbox a chance at life, old or first on or not.
@@Spyder7051 don’t worry I’ve brought my falcon back to life. I am a healer. Just hearing the soft whirring of the fans gave me an instant dopamine rush.
@@AMII.YT_KREW かけけけ
Simply amazing video! You made me think of all the old technology I threw away that could've been saved with simple tricks. Thank you for your work!
The part where you fixed the cracked case was outstanding work. Great job.
that's very nice of you, thanks for watching and the nice comment.
23:31 Look closely, it cracked again.
@@CoroaEntertainment cmon let people be happy
@@resEG how did you get that from
@@CoroaEntertainment yea he hides it from the camera after that
You did not install the CPU heat sink incorrectly. Compare 6:59 with 15:30 in the video and you will see the issue. It won't cool correctly with the heat sink 90 degrees off.
Such a noob hahah i seen that too .... hahahaha
This comment is 100% correct. Hope people don't use this video as a tutorial for the red ring fix
Oh my!
Okay I'll make sure I install the CPU heatsink incorrectly.
I was really amazed on how you restored the xbox 360 casing. Didn't regret subscribing to your channel!
I so appreciate you saying that - that was so sweet of you! thanks for watching
Good job dude
Great work!You did a good job on fixing the ring of death!You are a true life console saviour!👍👍👍
😂😁
He didn't even fix it. It's just a bandaid fix and I can guarantee it's broken again
Restoring the Xbox 360 Controller czcams.com/video/vYjYwM9Jklc/video.html
Ok
@@armyoftwo1164 mmmmnmmhmttethvgsaudduhdzh
⚽️⚽️⚽️⚽️⚽️⚽️⚽️⚽️🏳️🌈🏳️🌈🏳️🌈🏳️🌈🏳️🌈
Salut jai une question tu pourrais stp fair une vidéo comment réparer une xbox on s merci beaucoup
you forgot to clean the dvd device
Brutal me encanto la restauración y más con el reto al tener una de las partes tan partida. Brutal espero que sigas así cada vez trayendo nuevos retos, es un deleite ver un video así. 💪🏼👍🏻👌🏻
Me alegro de ver tu comentario, eso es muy amable de tu parte, gracias por mirar y el lindo comentario.
Hola vengo 3 semanas despues a decir que la parte donde pones los discos estaba con una cinta plateada y que al final no pusiste no se para que servia (seguramente para nada) pero que falto falto
yo hice lo mismo con la mia, pero volvieron a aparecer las luces de la muerte una semana despues
@@mithres4760 De pende de cualsea pero suerte 🤗🤗
@@espia_incognito9197 Esa cinta plateada es para la garantía, si esa cinta estaba manipulada ya la consola no tenia garantía
10 minutes later it is broke again
🤣🤣………😐
Awesome restoration and incredible transformation, the early xbox 360 was a great if troublesome. I loved mine. ❤
The part where you fixed the case was amazing. Congrats for great job
Es tan satisfactorio ver este tipo de videos no solo veo por ver si no también aprendo
Gracias!
¡Gracias! ¡Me alegra que lo hayas disfrutado! ❤️
Just a tip, never spread your thermal paste out like that. If this Xbox is actually used it will almost for sure overheat due to doing that none the less still great you got it working
He did that or are you talking about the person he got it from
@@5starr-dj819 probably the guy from video
I was thinking the same thing when I watched it. He put to much thermal paste on, and he didn't need to spread it out like that
it will fail again cause he just reballed it, too little thermal paste is worse than too much. The pressure of the mounting evens it out and just wastes the rest not making contact with the ihs and the heatsink, too little and u get gaps where thermal paste could be sat instead, the 360s problem was the heat from its components caused the board to flex and crack the pads/balls on the chip or board
Zero in my mind to the fact you were
Very good job, That case clean up came out fantastic...subbed!
凄い割れまで補修し ヒートシンクの辺りも清掃して 完璧ですね☆
I'm super happy for you that you managed to fix the rrod, but what you did is only a temporary fix. Only real way is to replace the solder balls under the cpu/gpu with lead solder
thanks for watching
Not true , lead free is better
@@garyhaas9575 Erm, no its actually nothing to do with the solder what causes the problem with these consoles, its to do with the clamps and the fact the main board is under large amounts of heat, cooling, heat, cooling cycles add the tension of the x-clamps, this causes micro fractures and separation in the solder balls present on the BGA, hence the RROD. Its just a shit design from M$. And that's NOT a reflow, all you did was heat the chip in a vain hope you reflowed it lol. Its similar to baking a GFX card
@@garyhaas9575 Lead Free is one of the reasons it happened in the first place.
Replacing solder balls is temporary fix too.
Resultado perfeito, melhor só novo 👏👏
Agradeço muito por você ter dito isso - foi tão gentil da sua parte! obrigado por assistir
Ele montou o dissipador da GPU errado causando problemas no fluxo de e causando aquecimento, fora que fez.reflow, onde o correto seria reballing
Xd
These kind of videos (I've recently learned) makes me very happy. Great stuff man!
Glad you enjoy it!
ainda quero comprar um desses tive muitos bons momentos cara seu trabalho e muito foda parabéns pelo cuidado e carinho que vc tem com cada componente dessas obras primas 👏👏👏👏👏
eu tenho um jasper ultimo modelo do fat e muito bom quando peguei ele tava com problema na gaveta que não abria substitui a correia e fiz a troca da pasta termica está funcionando firme e forte
Translate it to English...
Mhm….language….
Oi
Você pode aruma o eu coutrole
Nice video, but I noticed something: you mounted one of the two cooler wrong, rotated of 90 degree, the air will not pass through it
He said he realized when he was making the video and did fix the problem afterwards in Spanish a few comments below
Trabalhando excelente!
Parabéns. 👏👏👏👏
Yep, just another piece of art! Great work!
I love this video and you did a good job working on the xbox.
Nice work! 🙂
Do you keep these consoles after or re-sell them?
Also, I wonder if that small chip that came out at the start there was the corner from that cracked piece of the casing?
But all in all, an amazing restoration!
So glad to find your channel! Great content! Do you have plan to restore an old record player with broken dials and sliders? Would love to see that
Gracias a ti pude arreglar mi xbox no sabia como mis padres no me ayudaron pero tu fuiste mi salvación
It sad seeing the consoles so broken. Thank you for fixing it, it makes me feel better
sorry for being a dick-tease, but it was a temporary fix not a permanent
Nunca me dejaran de gustar estos videos tuyos, son muy entretenidos.
Jugadores de Xbox después de ver cómo reparar la causa de la muerte de sus Xbox 360 y volver a jugar: Eres tan hermosa como el día que te fuiste
that is a LOT of thermal compound you applied good lord.
I remember how hyped I was when I first time playing Lost Odyssey on this console
You have really improved the quality of your videos a lot lately. by the way, I recommend that you use a paint brush instead of a toothbrush for the peroxide cream, it distributes better and is much easier to handle.
thanks for the advice, I will use the paintbrush the next time, thanks for watching and the nice comment.
What cream is he using??
@@turji PEROXIDE. Could just be hair bleach and personally it's more a paste than a cream but semantics.
@@turji gamer juice
@@nykrev I'm pretty sure that's what he's trying to remove.
Great job, but the problem probably comes back in a few days.
That's why Xbox 360 emulation is a must. plus I had a white one that got the red ring of death every now and then. All I did was beat the living crap out of it. I hit the top of it and it eventually went away. Rinse and repeat for 6 years. Eventually I tried to paint it, it went bad. Left it outside one day and someone stole it. That thing was a tank! Beat it up every other day.
I had a repaired Jtag unit back in the day and it lasted only a few months after being purchased..... The 360 got hot enough to suffer from chip creep. I'd imagine to properly restore a 360 long term you'd have to upgrade the cooling in some meaningful way over stock. Liquid metal would really be the easiest solution.
This is ASMR. Actual repair begins right before 10 minutes for those that were recommended this video expecting someone to explain what they're doing
It's very strange that nobody mentions the thermal paste used in the video. Gd-900 is very liquidy paste which should not be used on bare die situations. Instead use PK-3, IC diamond Carat or a cheap solution would be Dow Corning TC-5688 which was specifically designed for bare die applications such as laptops and consoles.
I'm glad you didn't spray paint the exterior of the console you restored it the right way good job
This is weirdly satisfying. I have no idea why CZcams wants me here, but I'm not mad at it
thanks for watching
This man’s a legend for fixing the red ring of death
Oh, that's very nice of you, thanks for watching and the nice comment.❤️
@resEG you didn't even fix it. Just a bandaid fix
Nice video, but check the min 15: You're putting bad the heatsink! You must rotate it 90º, check with the video at min 6:40. In that position (min 15) you're blocking the air flow
I can't imagine the time it takes you to do these repairs with having to adjust every camera angle to every little step.. cudos!
I just took off the front of my 360, it was cool. Awesome video!
Show demais, muito bom ficou o 360 esse modelo é fantástico. 👍😀
Top demais excelente trabalho de restauração 😍👏👏👏
Sim mn
I recently repaired one of these, and I swear, I never want to take one apart again in my life! All those plastic clips were an absolute nightmare! It works, but the clips have gone for a Burton lol.
@@wannurazalina8607 why?
I'm so glad I still have my Xbox 360, which still works. Same with my Xbox that has the clear casing.
5:00 судя по повреждению её пытались починить Советским способом
У нас так телик любят чинить
Am I the only one that noticed that he put the CPU heatsink back on at a different angle?
Yup, that heatsink isn't going to cool properly.
I use to mod this kind of devices (Jtag / RGH) the way he did this maybe less then month if played daily. Honestly for this kind of repair if he wanted to do just a reflow using proper equipment like a BGA station would of been perfect all the heat gun does it throw hot air at the chip causing the board to warp because the whole board ain’t being heat up at same time. But again it’s just for a video so I’m guessing he might thrash it after or sell for parts.
Ikr
Great video. Always admired this kind of work. How do you bleach plastic?
فيديو ممتع جدا يبعث على النفس الرحة ممتاز جدا عمل رائع
You should have re-balled the cpu, not re-flowed the cpu. That system will die in a couple days up to a weeks time!
Shut up. Be glad it had even 1 minute of life
@@skittl9454 No bruh, only a psychopath would bake innocent parts like that.
Ask Louis Rossman about it.
@@BenderBendingRodriguezOFFICIAL €: ^ |
Reflowed mine years ago and its still going strong.. its a launch unit at well lol.
@@skittl9454 thats 2 words I like telling black people "Shut up"
красота) мужик у тебя золотые руки!!!
Большое-большое спасибо, рад, что вам понравилось! ❤️
Always satisfying 😌
thank you for watching
@@resEG :)
Awesome video mate! Did you reuse the thermal pads or did you apply new ones?
You’re not suppose to spread the paste. As you put the heat sink on the pressure will spread it out evenly
Poi ha veramente senso aggiustare in modo provvisorio una 360 oggi?? Forse giusto x fare un video da milioni di visualizzazioni..Si trovano delle Xbox One funzionanti con accessori e Giochi a pochissimo ornai ... 😅
Excelente trabajo de restauración solo hubo un pequeño detalle que no quedo bien y fue el disipador de la CPU las rejillas quedaron hacia un lado y eso a la larga va a crear problemas! Pues no va a permitir bien el flujo de aire sobre el disipador y va a calentarse más... pero en general buen trabajo!
Así es, y de paso podría hacerle un reballing para q dure mas la consola…
Glad that u used the original casing and glued it back together, it would’ve been too easy just replacing it
Ficou muito legal seu vídeo restaurando o Xbox sucesso pra vc
Это временно на пару суток игры потом опять три огня , задние крепления звёздочки слабые при нагреве и они ослабляют при этом проц перегриваеваеться и показывает ошибку, на своём вкручивал болты с шайбами и все было гуууд.
Спасибо за просмотр
Согласен, тут не реболл нужен,а замена GPU
@@IamLoveEBOLA это даже не реболл, а простое пропекание. Сами чипы нормальные, иначе бы не запустилось вовсе
@@leeeeeee2796 он ведь не только по гп и процу поводил, но и по памяти. Зачем? После этого он не должен работать
When applying thermal paiste , put a thin line at one end then spread with a credit card or something similar
homie drowned it in thermal paste lmao
No need to spread at all, it's only going to increase the risk of creating air bubbles. The heatsink will spread the thermal paste evenly when you attach it to the board.
@@Villa_Sempre that's why you spread it evenly with a card , no air bubbles
@@Villa_Sempre just to let you know , I fix these
@@garyhaas9575 just because you have been doing something wrong for many years doesn't make you good at it, it only makes you good at doing it wrong
In my opinion one of the most easy consoles there is to take apart!!
2009 Arcade Model Was is the best!! I still have mine and it works perfectly!
thanks for watching
Eline sağlık usta, beyazlatmak için ne döktün? uv aydınlatmam mevcut
Great 👍👌 work Xbox 360
thanks for watching
13:14 El disipador no va en esa posición!!
Desafortunadamente, no instalé el disipador de calor de la CPU correctamente, me di cuenta de este error más tarde, después de terminar el video, así que lo corrigí después del video.
gracias por ver
Creo que eso explica porque los ventiladores del disipador parecen turbinas de avión 🤔 , el pobre cpu debió de estar en las brasas del infierno 😳
Aun así buen video 👍
Eso podria explicar por que la xbox sonaba como turbina de avión?
@@X-BAIO почисти xbox от пыли
Me relaja este tipo de videos 😌😶
Proper good job mate!
Класс 👍👍👍👍👍👍👍👍👍
thank you for watching
Не на долго восстановление. Чип не перекатан а просто прогрет. У меня после прогрева проработал 2 недели
와 알고리즘!
what did you use to clean the outside of the device, and remove the yellow?
Bist der erste, den ich sehe, der die Klammern unter dem Mainboard wieder dran macht, habe die früher direkt weggeschmissen.
nie sądziłem że jeszcze w tym roku ktoś naprawia xboxy 360, jeju tamte czasy grania na tej konsoli były cudowne
Dzięki za oglądanie
😝
При чем здесь ремонт? Прогретые чипы все равно отвалятся.
Спасибо за просмотр
я просто немного не понял, проблема именно в отвале была? из за этого красное кольцо было? И мне кажется, термухи много навалил
Dude your awesome I gotta have you repair my Xbox 360 😅
Amazing work!
Thanks for watching
С учётом того, что ты не поставил термпрокладки на память проживёт она не долго.... В чём заключается твой ремонт ? Ты просто почистил мать, куллера и радиаторы от пыли( не более) А ну и прогрел два чипа, не понятно зачем ....
Короче сомнительный ремонт, проживёт не долго)
Ещё мне показалось, что корпус тупо новый поставил, т.к я и не увидел результат после того как он крышку склеил. Просто зачистил наждачкой и ультрафиолетом просветил, а куда шов делся?
да все нормально, 360 бокс давно уже нежитью стал, второй раз не умрет
а с такими толстыми прокладками много тепла не отведешь, что есть что нету
А никого не смутило, как он поставил радиатор на процессор? Повернул на девяносто градусов, и теперь он не будет продуваться, так что, работать ему дай бог пару дней
I really do like the design of the fat models. I have a mw2 edition. But I also have a slim 360. The fat has a jasper motherboard and I heard they were better at not red ringing but don't wanna take any chances.
10/10 - hugs from Romania
I so appreciate you saying that - that was so sweet of you! thanks for watching
I wished to see it when mine was broken. I would have send it to you for repairing it.
*Awesome Video Dear Restoration EG... Super Big Thumbs Up Brother!!!* 😎😁😀💁🏻♂️✌👍
So nice to see a game system getting restored to glory. So many game stores would be so quick to trash broken systems because the restorations just aren’t profitable.
Still to this day the best console ever made
Very good work 👍
Nice work 👊
thank you for watching
good ASMR relaxation
Thanks for watching
Você tem muito talento
Ah the ol red ring o death. I remember somebody even made a death metal song about it back then.
Great video, keep up the good work!👏👏👏
Thanks for watching
@@resEG дьдььдщ8дщщщд
@@resEG 9дд99лд9щддддд9ддддд899д89ьщдщ9щ9щщшьддддщщддь9ьдщщ9щддд9ддддд
@@resEG 9л9ддь9дщьддддд8д8999999д99д99д9дь999ьдддд99ь99щььщддщьддддд9ьдщщ8
здравствуйте д д9зло 9ь
incrível !! Great, good job
Soo what was the reason for changing the orientation of the cpu heat spreader
Très beau travail. Quel produit avez vous utiliser pour restaurer le plastique et la couleur de la xbox svp ?
Ficou top demais slk
Hola, Por favor trae más Xbox, Me gusta ver mucho las reparaciones, Gracias
gracias por ver
Restoring the Original Xbox (CPU overheating) - Retro Console Restoration & Repair
czcams.com/video/SKg_bzeDMVg/video.html
I hope you do this as your living..that was incredible ! 😊
Our school has a chrome disk drive phat Xbox 360 too, it still works
Man this gave me tears, I haven't played x box 360 in years.(although mine was black.)
Great job🔧
Childhood memories back again ☹️
Lo dire una vez mas tus videos me entretienen y son facheros
Great job/work the belt usually goes on the disc drive would of replaced that greased the gears and cleaned the laser for a full restoration interesting technique on the cracked cover shell was that a honey comb screen add on??
Ficou ótimo!
Satisfying video 😍
Bom trabalho ajudou muito!!