Video

Thanks for this video it allows me to try this with mine.

My window just randomly shattered for no reason! Thank you for this video!

Thanks you're the man , best video yet on pool pump 👌, more video's please 🙏

If you modify this video to say watch to the end because it’s on the opposite end of the engine, what is the point in even having the video out?

The exterior walls of my rca mini fridge are hot to the touch. Do you think this is the issue? I do hear humming from the condenser

When I repaired mine, the head of the brass screw that held the washer in CRUMBLED. I used a pick to pick out the remnants of the washer and luckily was able to get the rest of the screw out. The body was OK so I was able to figure out the thread size. I replaced the washer and screw in the parts department at Ace Hardware, Home Depot didn't have the right washer. Fixed like new! I'm still surprised that the brass head of a screw would completely crumble to the touch though. I was very luck that the city water meter is in the driveway in a box with an easily removed lid.

If it's a brand new cab that you have to assemble, you can probably dry screw everything (no glue) except the bottom (or the back in my case) then measure, not that your method doesn't work just that it might be easier to do this way. In my case the pipes come thru the wall into the back, and I have already dry assembled it (no glue just screws)..without the back panel and so when I have it in the exact correct position then I'll jot down my measurements. The other cabs have to be exactly where they are going to stay including leveling feet or shims or those measurements will not be accurate to it's final position.

The white part on top of relay gets to hot to touch

What was the size of the new washer?

You should also put mud down first, then tape and run your knife down go get excess mud out. Use quickset. If you put tape down first your basically just mudding in the mesh holes...

This is wrong advice. Paper tape is stronger then mesh. Mesh is preferably used on repairs... you also want to use a quickset with mesh tape,it is harder and will give more strength to the mesh.

Good info thanks 🙏

Considering the hassle of getting the water company to shut off the main any time you need to service this valve, wouldn't it have been a good idea to also replace the stem nut packing "while you were in there?"

This video is right on point!!! Saved me from going out to buy a new refrigerator. $5.19 part from Amazon and I’m back in business!!!

This has to be a joke lol 😂

Wish there was a video of getting the cover off 😂

I'm sure you never need to use it, but it goes bad anyway

Helped me so much thank you sir

Does anyone know which one is bank one and which one is bank 2

I prefer to build the deck 1 inch from the wall. This way no flashing is needed.

What code were you getting when you check the code

How much was the job to do this one pier? Thanks Tavis

thanks

Same problem. Everything else works fine on my dishwasher. Could you tell me the exact part number? Thanks so much for showing how to remove the end clip!!

how do i know if the relay is the problem?

....

This intro copulates respectfully

At 6:44, if you have reconditioned callipers, sometimes they are rough under the copper washers, and they leak. Just tap the top of that hollow bolt with a hammer, this will seat the washers better and then snug up bolt.

How does it work without capacitor ?

Thanks for sharing 👍

Shouldn't that flashing go behind the tyvek against the sheathing?

None of these IS going to match. None IS big enough. NONE is a singular subject. Two are, one is, none is...

I was rooting for the mouse...

I tried it but still not working. I wonder if I put the cables right🫨🫣

Thank You🌸

Thank you 🙏🏾 ❤

Wrong! You have to use hot mud with mesh it will fail and is not a warrantied by mesh manufacture

Excellent video, short and to the point with every step explained clearly and easy to follow. Thank you

Should have just put a ball valve in.

How do you re-attach the bottom piece of siding? Since the siding gets nailed at the top and the rest of the siding over lap each other then how would you nail it back up?

love it! thanks for making the video!

This is super helpful. I have one I my yard and didn’t know how to fix it. I almost thought to just cut it. I’m glad I didn’t.

Mud the seams first then tape.

Just had mine replaced with a ball valve.

All the old hardware stores around me have pretty much gone out of buisness and now im stuck on speeding 3$+ on a bolt

I checked the AC voltage of the 2 wires, its like 1.5vac...does that mean I should check the board as well?

Great job.

I have a textured ceiling and came loose at wall seam. Any suggestions? Was thinking maybe an adhesive then paint over

Did this, exactly, even in garage like this. Does not work. Mesh tape is a gimmick. 3 months later it looked worse than before I started. And now all needs pulled down and done right with paper tape.

I got a similiar fridge. Noticed today it would just click every so often and it wasnt running. I touched the compressor and it was warm. I hear nothing running. Would that relay be the problem or does the relay not control the fan?