![Colin Hill](/img/default-banner.jpg)
- 54
- 277 090
Colin Hill
United Kingdom
Registrace 25. 08. 2013
Ikea Double 3D Printer Enclosure Review - METOD Model 23 3/4" Deep - cheap DIY alternative
3D Printer enclosure made from Ikea METOD wardrobe (similar to Ikea Platsa version) but 60cm (23 3/4") deep. Home build DIY - a professional looking 3D enclosure for less than purpose built 3D printer enclosures.
Future videos will add lighting, extractors and other items, so subscribe to keep updated.
Ikea parts used:
METOD high cabinet frame 60x60x220 cm
2x FONNES door with hinges 60x40 cm white (includes hinges)
2x SINDVIK glass door 60x64 cm white/clear glass
2x BESTÅ pair soft closing/push-open hinge - for Sindvik doors
3x UTRUSTA pair shelf 60x60 cm white
Sound deadening sheet material: Amazon UK amzn.to/3mKMxA1
I cannot find the same product for USA, but something like amzn.to/3Jv5a45 may do (its actually thicker).
Future videos will add lighting, extractors and other items, so subscribe to keep updated.
Ikea parts used:
METOD high cabinet frame 60x60x220 cm
2x FONNES door with hinges 60x40 cm white (includes hinges)
2x SINDVIK glass door 60x64 cm white/clear glass
2x BESTÅ pair soft closing/push-open hinge - for Sindvik doors
3x UTRUSTA pair shelf 60x60 cm white
Sound deadening sheet material: Amazon UK amzn.to/3mKMxA1
I cannot find the same product for USA, but something like amzn.to/3Jv5a45 may do (its actually thicker).
zhlédnutí: 8 784
Video
Prusa Box How to Wire Up Raspberry Pi Fans, LED Lighting Temperature Controller, Relays. 3D Printing
zhlédnutí 1,1KPřed rokem
This video shows how i would connect the electronics inside a Prusa Box 3D printer enclosure, including connection to PWM fan controller, LED strip lights, Raspberry Pi, buck converter etc. I also recommend viewing these videos: PWM Fan Controller - czcams.com/video/6syvzzSb0Yc/video.html Connecting relays to Raspberry Pi with Octorelay - czcams.com/video/WpepmsB_Cco/video.html Prusa Box enclos...
Audi S5 Muffler Back Box Delete - 4.2L V8 (2010) B8 - pipes by Zaustworx
zhlédnutí 6KPřed rokem
Audi S5 muffler back box delete - do-it-yourself pre-made 'bolt-on' delete pipes by Zaustworx. For B8 4.2 version. Before/after cold start and view underneath, plus a short run in comfort and sport mode around town. Just cut original pipes 3" from the weld on back box. Slide on new pipes, add exhaust paste to seal pipes, then tighten the U bolts. Takes 30 minutes. Fitted by vasworks.co.uk Delet...
Prusa Box PWM Temperature & Fan Proportional Speed Control For Modular Front 3D Printer Enclosure
zhlédnutí 1,6KPřed rokem
Demonstration how a PWM fan controller can be fitted to PrusaBox 3D printer enclosure modular front module to proportionally control the speed of the extractor or any cooling fans Useful Links: Face plate for my controller box as per the video - www.printables.com/model/325501-pwm-control-module-for-prusabox-modular-front PWM Controller - UK amzn.to/3U7Tmar USA: amzn.to/3sKrpKa Fan connector fo...
PWM Extractor Fan Speed Controller PART2 for 3D Printer Enclosure - Tukkari, PrusaBox, Lack Box
zhlédnutí 1,1KPřed rokem
Part 2 Demonstration how a PWM fan controller can be fitted to a 3D printer enclosure to proportionally control the speed of the extractor or any cooling fans Useful Links: Face plate for my controller box as per the video - www.printables.com/model/278149-3d-printer-enclosure-raspberry-pi-3-line-display-s PWM Controller - UK amzn.to/3U7Tmar USA: amzn.to/3sKrpKa Fan connector for the board - se...
PWM Extractor Fan Speed Controller for 3D Printer Enclosure - Tukkari, PrusaBox, Lack Enclosure
zhlédnutí 12KPřed rokem
Demonstration how a PWM fan controller can be fitted to a 3D printer enclosure to proportionally control the speed of the extractor or any cooling fans Part2 shows the completed PWM controller mounted. Useful Links: Face plate for my controller box as per the video - www.printables.com/model/278149-3d-printer-enclosure-raspberry-pi-3-line-display-s PWM Controller - UK amzn.to/3U7Tmar USA: amzn....
Raspberry Pi with display, safe shutdown temperature fan & light control for 3D printer enclosure P2
zhlédnutí 1,3KPřed rokem
Part 2 - Modify your 3D printer enclosure with Raspberry Pi with Octoprint, new 3 line display, temperature control and lighting control. Fits any enclosure type and includes STL and STEP files. Part 1 - The first video covered adding the 3 line Raspberry Pi display and shutdown switch so read this first czcams.com/video/XtgQlkpMjk8/video.html (also includes a parts list) This video expands on ...
Raspberry Pi 3 Line Status Display, Safe Shutdown & Reboot Button - Ideal Octoprint, Rasbian - Pt1
zhlédnutí 1,7KPřed 2 lety
A 3 line status display for Raspberry Pi 3B and Pi 4, includes a safe shutdown button and safe reboot button. Useful for 3D printer Octoprint or just plain Rasbian. Subscribe to see the next episode... The grey case in the video is my own design, and will be used with a Pi 3B (extra design for Pi4 available) and relay hat to control extractor fans, thermostat and lighting for a 3D printer Tukka...
Prusa Box Spool Tank Update - Sealed 3d Printer Filament Enclosure for All Printers
zhlédnutí 2,1KPřed 2 lety
Update after the build. A 6 roll 3D filament storage box providing individual filament output feeds. Also suitable for the Prusa MMU. Designed to fit directly onto the Prusa Box enclosure, but can also be wall mounted and therefore suitable for all other makes of 3D printer enclosure. The sealed option helps to prevent moisture build up. This is part 3 of a 3 part video. Please SUBSCRIBE to ens...
6 Roll Filament Sealed Spool Tank Enclosure - For Prusa Box & Other 3D Printer Enclosures - Part 2
zhlédnutí 1,2KPřed 2 lety
A 6 roll 3D filament storage box providing individual filament output feeds. Also suitable for the Prusa MMU. Designed to fit directly onto the Prusa Box enclosure, but can also be wall mounted and therefore suitable for all other makes of 3D printer enclosure. The sealed option helps to prevent moisture build up. This is part 2 of a 3 part video. Please SUBSCRIBE to ensure you don't miss futur...
6 Roll Filament Sealed Spool Tank Enclosure - For Prusa Box & Other 3D Printer Enclosures - Part 1
zhlédnutí 980Před 2 lety
A 6 roll 3D filament storage box providing individual filament output feeds. Also suitable for the Prusa MMU. Designed to fit directly onto the Prusa Box enclosure, but can also be wall mounted and therefore suitable for all other makes of 3D printer enclosure. The sealed option helps to prevent moisture build up. This is Part1 of a two part video. Useful links: Prusa Box web site for the Prusa...
Simply Audi Car Show 2022 Beaulieu National Motor Museum, UK
zhlédnutí 550Před 2 lety
Something different to my normal channel content. For anyone attending this Audi car show event, check out www.colinhillphotography.uk for still images and free digital downloads. Music from Uppbeat (free for Creators!): uppbeat.io/t/hartzmann/clear-sky License code: JIKHCRND6TQRANY9
PrintWatch for Octoprint. Still Broken? The Spaghetti Detective alternative
zhlédnutí 830Před 2 lety
Follow-up review on Print Watch plugin for Octoprint, now upgraded to version 1.0.20. How have the changes affected this app, designed to automatically stop a failed print. Recommended sites: Printpal.io [the PrintWatch website] PrusaBox (enclosure for Prusa Mk3s as shown in the video) - www.printer-box.com/?wpam_id=1 Tukkari (enclosure shown for Pruas Mini) - www.tukkari.com (www.tukkari.store...
NEW Octoprint PrintWatch - alternative to The Spaghetti Detective?
zhlédnutí 3,3KPřed 2 lety
PrintWatch for Octoprint competes with The Spaghettit Detective to monitor 3D printing using new artificial intelligence-based defect detection software for use with 3D printers, in conjunction with a webcam and Octoprint. Update 23 Feb 22: Unfortunately PrintWatch has so far not issued any updates to the plugin tested (v1.0.18). Update 22 March 22. version 1.0.20 Follow up video coming soon
Prusa Mini Z Axis Fail - SOLVED - Self Test Wizzard
zhlédnutí 7KPřed 2 lety
How to solve Prusa Mini with Z axis self test failure when using the built-in calibration wizzard. I provide TWO solutions, so please watch all of the video to gain full benefit. FREE: Download the STL or STEP file (so you can change the thickness to your own requirements) at www.prusaprinters.org/prints/120134-prusa-mini-z-axis-fail-self-test-solution-length-o The Prusa Mini enclosure in the b...
Raspberry Pi Relays - connect to Octoprint and Octorelay for 3D Printers, installed in Prusabox
zhlédnutí 8KPřed 2 lety
Raspberry Pi Relays - connect to Octoprint and Octorelay for 3D Printers, installed in Prusabox
Einsey Motherboard Cooling Solution for Prusa Box 3D Printer Enclosure for Prusa Mk3
zhlédnutí 2,6KPřed 2 lety
Einsey Motherboard Cooling Solution for Prusa Box 3D Printer Enclosure for Prusa Mk3
Prusabox PSU Cooling Fans for Prusa MK3s Power Supply when using Prusa Box 3D Printer Enclosure
zhlédnutí 1,9KPřed 2 lety
Prusabox PSU Cooling Fans for Prusa MK3s Power Supply when using Prusa Box 3D Printer Enclosure
Prusa Box detachable corners to remove top section of enclosure - modification - easy access
zhlédnutí 2,4KPřed 2 lety
Prusa Box detachable corners to remove top section of enclosure - modification - easy access
Prusa Mini Fit Bondtech Heat-break and nozzle step-by-step, stop clogs and clicking
zhlédnutí 8KPřed 2 lety
Prusa Mini Fit Bondtech Heat-break and nozzle step-by-step, stop clogs and clicking
Prusa Mini LED Lighting - Tukkari Enclosure
zhlédnutí 2,4KPřed 2 lety
Prusa Mini LED Lighting - Tukkari Enclosure
Wyzecam (logitech / Pi Cam) Webcam Mount for 3D Printers - Portable, Adjustable Height
zhlédnutí 927Před 2 lety
Wyzecam (logitech / Pi Cam) Webcam Mount for 3D Printers - Portable, Adjustable Height
Temperature Controller w1219 for 3D Printer Enclosure - Prusa Box - Prusa Mk3s - Wiring and Fitting
zhlédnutí 7KPřed 3 lety
Temperature Controller w1219 for 3D Printer Enclosure - Prusa Box - Prusa Mk3s - Wiring and Fitting
Prusa 3D Printer Enclosure - Fitting PrusaBox Modular Front - Pi / Screen / Octoprint Octodash
zhlédnutí 17KPřed 3 lety
Prusa 3D Printer Enclosure - Fitting PrusaBox Modular Front - Pi / Screen / Octoprint Octodash
Raspberry Pi Power Switch Button - Safe Shutdown / Start Up
zhlédnutí 17KPřed 3 lety
Raspberry Pi Power Switch Button - Safe Shutdown / Start Up
Add a Power LED to your Raspberry Pi Case - Octoprint - Octodash - 3D Printer Enclosures - PrusaBox
zhlédnutí 3,3KPřed 3 lety
Add a Power LED to your Raspberry Pi Case - Octoprint - Octodash - 3D Printer Enclosures - PrusaBox
3D Printer Enclosure - Extractor Fan with Temperature Controller - Wiring - PrusaBox, Tukkari, Lack.
zhlédnutí 20KPřed 3 lety
3D Printer Enclosure - Extractor Fan with Temperature Controller - Wiring - PrusaBox, Tukkari, Lack.
PrusaBox - Wyze Cam 2 & 3 Webcam Mount for 3D Printing Enclosures
zhlédnutí 1,8KPřed 3 lety
PrusaBox - Wyze Cam 2 & 3 Webcam Mount for 3D Printing Enclosures
Prusa Box - Fitting LED Lighting: Prusa MK3 Enclosure
zhlédnutí 4,3KPřed 3 lety
Prusa Box - Fitting LED Lighting: Prusa MK3 Enclosure
Prusa Mini - Front Mounted USB & Power Switch
zhlédnutí 4,8KPřed 3 lety
Prusa Mini - Front Mounted USB & Power Switch
Merci pour votre aide Colin. L'étalonnage de l'axe Z a très bien fonctionné. Je n'ai trouvé la solution nulle part. Cordialement
Zero air flow putting fan on a closed flat surface... Real smart
@@daledidomenico5341 yeah? especially as the feet of the enclosure raise it a few mm above table height so there Is airflow!
What kind of pins should i buy for this "4 Way 3.96mm PCB Connector Housing" ?
If you can find the plug then I'm sure there will be a link for the relevant pins on whatever store you use.
this is my first real pcb/electronics projects so im a compleet beginner. can somebody help me find the connector he is referring at 1:48? and how do I wire it to the to cable extension?
Assume you looked in the description which details the connector type. You will need to chop the end of the ext cable and fit new pins. Good luck
Solved my issue. thanks!!
Hello. I wanted to know if this device could be connected to a 12v 2-pin fan. And another thing, I want to use it so that the fan starts when the temperature rises below a certain value, and stops when the temperature drops below a certain value. Can that be done with this device? Thank you.
If you only have a two cable fan then try this czcams.com/video/iNBipWZxWxI/video.htmlsi=YJwO_SIO4L55M0Pv. You won't need the speed control board.
It works if I want to put an arcade button for the power on ? ./pi-power-button/script/install
£380? I got complete Peco system custom made and fitted for £650 Yours sounds deeper though sir I may get them to remover the resonators lol
Have you got a link to your exact setup please it sounds amazing
www.zaustworx.co.uk/product-category/car-exhausts/audi/s5/s5-b8-4-2-v8/
I've the same problem, but with the y-axis. I already reassembled all. Y-Axis says 191 and idk how to change it.
Y axis shouldn't change
Hi Collin. Thanks. I have 4 noctua fans, pwm. I would like to have them in a server rack, but with possibility to control the speed, due to the possible loud noise. What do you recommend?
Great video and explanation! question, which rasp OS are you using to boot straight to your application? thank you!
Octoprint
Does vibrations from one printer affect the other printers quality in any noticeable way? I have two prusa minis and considering IKEA Bestå.
When i have them both running i dont notice any issues. The enclosure is bolted to the wall to help stop movement. Each printer is also on a rubber mat
THANKS
I had these on mine and they droned a bit when you accelerated at motorway speeds but sounded really good around town.
Hi Collin, thank you for this brilliant video. I try to source the parts. What kind of wires (mm) do you suggest for the power supply? Thank you!
Hopefully my links will help you. For wires, nothing too thick. 16-22 gauge flexible wire. Or even just fan extension wires. It's only using 12v and less than 1 amp. Good luck
@@colinhill Thank you for your quick answer!
Great video! I am just running into similar issues, I hope your advice will solve it. Did you mention you replaced your extruder? Can you share what extruder do you use, and why?
Bond tech Ifs extruder, it doesn't jam like to stock extruder and also more quiet
@@colinhill Does it make a change for Prusa when accessing their support?
@YigalBZ well you can't really say you have fitted it. Choice is yours, wait until the 12 month warranty has expired? Or worst case fit the old extruder if you have to do a return. I found the new extruder faultless in operation. I also recommend using the bond tech heatbreak.
@@colinhill 191 into the secret menu...Hooda thunk. I ran into that today after an attempt to update the firmware failed, and I spent a couple of hours in Chat with the very nice Prusa people. I was in the pre-order crowd for the original Mini. It seemed pretty good for a while, but then I started experiencing a mix of extruder and hot end problems. I installed the Bondtech extruder and heat break and things were much better. I did modify the heat break installation (used a small soft mouth clamp) and also added three slightly longer stainless cap screws so it was easier to adjust and set. I'm probably going to try the Slice Engineering hotend upgrade kit next.
Hi, great videos! I am considering purchasing a PrinterBox for my MK4. How long would you say it took to assemble the box from start to finish (not including the Pi - I won't be using a Pi in this box). Thanks!
Hi. You could probably build it in a couple hours. Time consuming part is printing all the parts.
@@colinhill thanks so much!!
Thank you very much for the explanation, I learned a lot from you. 👍
Isn't capricorn tubing tighter? As the PTFE tubes are only there to guide the filament and not feed like in a normal bowden setup, wouldn't you want the tubes less tight? (like the 4od 3id mm ones)?
Thank you! This helped really much 😊
Thanks for sharing, as I have Metod and wondered if the Sindvik would need additional holes to mount
thanks for that, given me a great idea for enclosing my Prusa Mk3s and recent Bambulab A1
Great job I have been unable to locate the back adapter plates for the conversion for pmw I checked on Prusabox and Printables the plates I'm referencing are in this video at 1:59. would greatly appreciate some guidance to find them. Thank you in advance sir
i'd been trying to adjust the spinda forever to get the self-test to pass on Z axis, and replaced the trapezoid not all to no avail! Adjusting to 191 (I also have the bondtech) and now everything's green! thanks!
perfect sound. no need for expensive exhaust systems
hi colin i dont understand why you need the buck converter when all components are 12v
4:30 for set up
Hi Colin, thanks for the in depth video! Cause of you I just collected all the mentioned stuff from the PO Box. I will use your design on my TLX for the MK4 and I was just asking myself if you have a new design of the PSU shroud which fits the noctua 40mm you have in this video. Also since the TLX just hs 2 screwholes for the PSU shroud I would be happy to get the step or fusion file for your shrould to change it to the "new" tlx layout.
Hi, i have uploaded the step file to Printables, so i can allow you to make a remix. Glad you find the model useful.
Thank you! I will post the remix with your credit when I am done. Have a great "rest weekend"@@colinhill
Hi Collin, I cant fin a cable that goes out from the pcb to a fan splitter, can you help me out^ Thanks for the vid!
There are 4 cable fan extension and splitters on Amazon, but you will need the larger special plug for the PCB mentioned in the description, unpick the fitted plug from the cable and insert the pins into the larger plug.
thank you!@@colinhill
Minute 1:54, you use an extension cable, but have you changed the connector? That white female connector is different, it is wider. What is that connector called? The connector on the Zhiyu board is wider than any 4-pin connector and I don't know which one I should put. Thank you!
Hi, please see the description as I mention details
@@colinhill Oops! Thank you!
Followed your instructions by watching the wiring 10 times lol. Not a big hero with electroncis but got it working. Thank you so much!
i am reviewing all your video's but where the heck did you order that buckconverter? My prusa box is assambled now so it's time to do some upgrades :)
Just from amazon
@@colinhill do you have a link? Cause they have a ton of buck converters there. Love you videoos btw. Got myself a second hand brand new prusa box for just 110 euro's.
@@hansstraat1978 UK or USA?
@@colinhill Netherlands :) thanks, everything from UK is more expensive now.
@@hansstraat1978 www.amazon.nl/ICQUANZX-Converter-Transformer-Voltage-Regulator/dp/B07RGB2HB6/ref=mp_s_a_1_12?crid=2O6XN9HQ8766V&keywords=buck+converter+12v&qid=1697742457&sprefix=Buck+converter%2Caps%2C101&sr=8-12
what is the temperature during several hours of printing? Will the power supply and electronics withstand such temperatures?
Petg around 33°, could probably get much hotter if door seals are added.
@@colinhill is this temperature ok for electronics?
@@tomasz9131 electronics normally ok up to 40°. If worried you could easily mount the PSU outside and pass cables through a hole in the side of enclosure. I considered this but at 33° it's fine. If I sealed the door then might consider it, or if I regularly did ASA which makes enclosure hotter. But if I did that I would also add an extractor with filter to control temps. I have done that in other videos on other enclosures.
Thank you so much for this video, I have the exact same relay board and no instruction so of course I wired it with the wrong vcc pin and it drove me nut with the relays working randomly when they felt like it. With your wirering instruction it works like a charm now. Thanks again!
Very helpful. Well done video. Thank you!
Manual?
Auto
@@colinhill I installed the same silencer remover from zaustworx and I don't get as good a result
Is yours the 3L v6, or 4.2 v8? After 3 months its sounding even better, burbles around town just doing 15-20mph which is mainly what i wanted so people know you have a V8. 70mph pretty quiet inside cabin. On fast accelleration it is loud. If yours is manual you could remove centre resonator to make it louder, not recommended on auto's due to drone. For me its definitely loud enough.
I have the 4.2 V8 year 2009 in automatic transmission however I live in France my vehicle is European perhaps they are designed with other standards which is indeed can explain this difference we understand clearly that it is a V8 but it doesn't purr as much as your video
Hello Collin, respect. The circuit is really great explained by you. However, I still have one question for you: Does the circuit also work with a simple 2 cable control of the fan? Greetings Frank
A 2 wire fan won't be speed controlled. You would be better using a different type and I cover that in another older video
Very neat solution Colin! At the end of your video you talk about making a fire extinguisher system video. I have not managed to come up with a practical solution using CO2 so as not to ruin everything with powder or foam. I would be very interested to see what you plan to do
It's currently down to costs. Each unit is over £$100. Would be gas based.
Thanks for this tutorial. Can I ask you how did you power the screen?
It's a DSI screen that connects via thin ribbon cable to one of the Pi ribbon cable outputs.
Thank you @@colinhill
Bonjour, ou peut-on trouver les fichiers des entretoise arrière svp ?
ok je les ai trouver cool.
I am currently following your idea, I have purchased the materials and built the Metod. Did you brace the back of the unit with a plank of wood by any chance? Thank you in advance.
I didn't need to brace the back. But I made sure it was connected to the wall using the supplied mounting brackets that fit at the top. Iw won't move for sure. I'm really pleased with it.
@@colinhill Thank you. Because my wall is boarded I decided to use carpenters modesty blocks to reinforce the Metod and used some spare shelves to reinforce the backs of each compartment for the printers. Do you have a solution for having the PSU outside of the Metod? If we are printing with PETG and ABS/ASA then 45-50C+ is going to reduce the lifespan of the PSU.
Great, thanks for sharing 👍
Thanks for the video. Does it keep all the settings after power off? Or must I reprogram my temperature settings at each power on?
Yes it does
where did you get your material enclosure ?.
You mean the Tukkari TLS enclosure from Tukkari.com?
Yes. I found them. Thanks for ur response.
Good video. What 12V to 5V power converter are you using?
Makes vary but just something off Amazon. Probably more coverage on my other videos if you look through the fan and led lighting
I just wanted to say thanks for the great how to! I was using this on my octoprint, and recently switched to Prusa Link/Connect. The switch and script still work great!!!! Thank you Colin!
I've been looking to get these on my S5 for a little while, other videos didn't really show what I W as after as I was worried about the cabin drone, did something similar on a mk5 gti and i ended up taking them off again as was too loud for me and I got a resonated system instead. Thanks for the upload - this has given me my answer, this will be too loud for me.
Can be loud at times but it's the only reason why I look forward to driving the car, always gives a smile
Can I set the close temperature above the start temperature? That way I never go too slow. I was thinking running 12v dc compressor ,and I think if it runs too slow it might damage the compressor...
No.
thanks you solved my error 🤠