Video

If the quiet core sounds the same as stock then why spend all that money. Makes no sence

The F6A engine was used in the Suzuki cappuccino and they make performance mods for it such as .04 overbored pistons, 280 cams, and more, it's pretty cool

Good vidéo. Sorry for m'y english but i'm french. I restaure this type of motor and i would like to know the torque to be applied to the piston rods and the cylinder head gasket, you Can Say to me please? Thank you

What model valve spring compressor do you use?

I've got a 2014 rzr1000 it has 3100 miles zero issues stock belt and it's been well used😊

Hey James I seen your video about replacement of the a/c evaporator in a dodge ram 1500 and i seen you are located in texas based of the sticker in your windshield . And i was wondering if you do any kind of mechanic work. I have the same truck but 2000 model and the a/c evaporator needs replaced and i have the parts just unclear what to do because of video quality! I am located here in arlington texas

"Two Nuts that have to be removed from the cab"..... The Driver, and the Passenger 🤣

this is good information for people who are wanting to put the hot cam conversion shim kit on They would sell more of them if people knew this i just bought that kit and head studs definitely going to try this before I pull the head if you did it again is there anything you would've done different Would it be easier to pull off the bed

Thank you so much 😭😭😭

Hello, Are you interested in testing our products? We would like to invite you to test the Scratch-Resistant Windshield for your 2018 RZR 1000XP

Did ya extend the outdoor shower hose yet?

No Smoking inside the Shop! Not very safe. Did not see exactly how you removed the Heater Box. Not trying to be Mean. Just stating the facts.

It is Illegal to let Freon Ex cape into the Air. Also will spray in your Face. Let People Know that the Shop needs to save the Freon.

Hello, Are you interested in testing our products? We would like to invite you to test the Soft Cab Enclosure Upper Doors for your 2018 RZR 1000XP

Awesome video!!!

Awesome video first time I've seen a video of me riding. I could tell my dog was enjoying it

Finally got to wash the KRX today. It's clean enough and ready to go out again and get muddy

I feel the same, try to go on a nice quiet road and always someone in my rear view, never fails. Anyway I have an '05 TJ Rocky Mtn 4.0L, by far the most fun and capable vehicle I've had. Jeep O|||||||O Only in a 2 Dr '41 - '06

What lake is it

can also pull magneto w 2 bolts longer than installation bolts but turn one way starter clutch to make sure longer bolts go thru it.

can time it with the cover off, just make dead nuts sure its at tdc first.

CZcams forced me to mute a song in the middle of the video. Sorry guys....

Lovely upload bud, this hike looks great!

Louder than factory ?? Our DNR cites for exceeding the decibles....a lot.

Thanks for the video, I found this link on Ram forum. I have a 1997, 2006 and 2007 Dodge truck. I love each of them for their respective jobs, but all have absolute garbage AC and Heat. All 3 have weak heat and weak AC. It hurts the most with weak heat in the 1997 plow truck. The 2006 quad cab is probably the worst - weak heat and NO AC. All 3 are heading to my mechanic in some sequence this spring/ summer. Probably expensive, but way cheaper than new truck BS and DEF and crap warranty

Could you show how to do a heating core flush?

Comment ! 😛

Lots of mud . Looks like fun !

Nice TJ . I can't wait until mine is back on the road .

thanks for the vid man! will be using this as a guide to remove the dash in my 95!

Thanks for sharing

Great video! I’ve got a 94 carry (DD51T). Looks to be the exact same thing as yours. Just to confirm, you only were able to get heat to come out of the defrost, correct? I’ve read that some models also have heat at your feet ….but mine is only defrost too I think

Same on 4th gen 1500?

Great Video! Thank you for the valuable information; as you said there isn't much online for these older Carry/Every's. Appreciate it!

awesome video my guy. some subtitles with the steps would be a helpful addition!

I really like your video, straight to the point,simple but full of info

New followers here you're awesome

my pro XP did the same thing when I put 100 octane fuel in it, after I put normal 91 octane fuel back into it it stopped doing that at start up

Jesus loves you

Hey thanks for putting your video out here. Maybe you will see my question and respond. How did you keep the piston(s)/crank from moving when you supplied air? Breaker bar or blocks of wood or something? I'm about to do this to a 2012 900. Leak down results were 9% on #1 and 3.5 on #2 but it does smoke a lot of oil. Doesn't seem to actually run out of oil that fast though. 2500 miles and hours. Wood blocks is how I held the engine still because I was worried the engine might turn either way from top dead center if I just used a breaker bar. I didn't want it to turn the opposite way I was holding it with a breaker bar during the actual removal process of the valve springs because then the piston could drop far enough and probably change the air pressure and let the valve fall... I could also hear a tiny amount of air come from the exhaust, intake and oil reservoir cap during the test. I didn't check the coolant. I used a digital compression tester before this and got odd fluctuating numbers for each cylinder after i warmed it to 180°. #1 196, 221, 204. #2 223, 204, 216. Normally the gauge gives me closer readings with other applications. Sorry for the info blast but looking forward to a response.

That's a job I am going to try to avoid.

I recently saw a video on Facebook of a guy that opening a track near Honey Grove it's a 10 mile long course. Looks like fun

Love your video! Are you interested in reviewing our aftermarket accessories in a video? If you are, please provide the specific model of your vehicle so we can see what we have available for your SXS. And share your email please, we'll send you more details.

Thank you! Looking at buying a 1988 with blown motor. Your work is very much appreciated!

Was out there yesterday with 6 KRX 1000s, fun but creek is almost dry.

Thank you, excellent - goodnight!))

I like the RedNeck cherry picker.

Great video, I have to rebuild my engine. The timing belt went. How many hours would the entire rebuild take; including removing the motor and painting and then putting it back in the truck?

How has this engine kit held up since rebuilding? Curious about the reliability....Thank you.

Got a link or a name for the cans so I can find them? I’ve been looking for Abit LOL I just bought a 18 Polaris rzr S 1000 ESP and man do I want those kicker cans ! Lol