Video

Could you just use jb weld instead of actually welding?

I had a worse situation. The bolt was stripped to hell. The brake line was broken so I cut it to get a better grip on the bolt, and I stripped it even further. It was pretty much completely rounded at this point. Luckily, I was able to get a perfect fit with a vice grip to get that sucker off

Don't buy any USED car from the rust belt if you value your money! If they made the pin in the latch handle out of stainless steel, NOBODY WOULD HAVE THIS PROBLEM with this handle. Poor engineering, the replacement part should have been upgraded.

The wand in the description is wool wax. Does that wand work for the fluid film?

Great information you have put together and provided to all. Thank You!

SEM makes a product specifically to simulate the grain of plastics like your dash. I'm not sure those "texture" products were what you were looking for. Nice job on the project overall though.

I’ve never thought to just run the reverse wire into the plug…how does that work? How much wire did you expose?

👍👍👍👍👍 it looks great but you gotta go back and paint the oil plant lol awesome I hope you had a great memorial weekend. oh and by the way, I’m a new subscriber and your first video was you talking about the laser machine and you were definitely not part of the debate team in your school because you sounded like a robot lol.

Moran

Impressive!

the "heavy clear coat " 3rd pass you did your arm was movin a tad too slow.. hence the runs, but runs in clear is no big deal.. like orange peel it can be buffed out.... cool vid

Back in the oder days my dad, grand dad, and great uncle used used motor oil and diesel fuel in a garden pumpp up sprayer to under coat there pick ups ! Here to tell you my great uncle had the cleanest working 74 International 4x4 3/4 ton with 401 4speed !And 72 olds 98 in the late 80's that would make new car owers jealous ! No rust on either of those cars and he moved here to WV from Akron Ohio ! So wasn't like he moved from the south to WV ! He moved from salt city Ohio to mid state sinderville WV ! Yes sinders (extra small black stones spinkled on intersections and hills to add traction in iceyand snow conditions !)

what grit did you use to wet sand the orange peel?

fantastic ill be sending you my old-school hot rod mags to fix up for me great job

Just wanted to say thank you. You do a great job explaining things.

To prevent brake dust, use ceramic brake pads, semi-metallic pads will leave brake dust on any wheels.

on a old Jazz MK2?? mind boggles

Expensive prices for old car

Sorry. u try. very messy. u cut down all the crack lines deeper to fill in the foam. U should fill in the crack only. the foam end up cover the whole area which is very unnecessary Creating more work for yourself. looks horrible. U might as well spray the whole dash. With proper preparations and the right glue the vinyl wrap would have been cleaner and faster. Final note . ebay would have been a better options lmao

there is a leather paste fuller to fix leather seats cracks to fix the cut on the edge.

The cornor light also signals when you turn and the aluminum side step is oem

Hey great video and info. What’s the name of the company you got the paint from? Thanks

I actually liked the look of the spatter paint as is but excellent work! I've got to fix my Jeep's dash and you've given me the courage to jump into it!

I wonder whether it would have been easier and less risk of error by eliminating the foam application and going straight to filler.

Literally everything you listed is wear and tear.

This product available in India.

Nice video how long will 2008 Tacoma last before one will looking out for route?

Will you still be able to use it in an engine afterwards?

No way that axle nut is tight enough

As a welder, clean your metal more, and do longer beads. When you stop and start like that your having to re create a puddle adding more and more heat than you need to make, also if your not experienced your starts may not have as much penetration so doing longer beads will let you keep a deeper penetrating weld going.

Thank you man I'm just confused on the bit fo u paint the inside or leave it

Great tutorial and amazing choice of music. Thank you for sharing.

Super 👍🤔

Great video. I learned a lot from all the little details!

This technology is amazing🎉

piston ring grooves as well?

How many hours did this task take mate?

I have a question when removing the two bolts from the wheel hub (still learning part names) and the strut my strut forces down and I can't bring it back up would I need a specific tool or am I doing something wrong? When I watch your video it doesn't force down at all

I'm a professional keyboard warrior and this made me cringe! Just kidding about both, I think it turned out super!

BEWARE CZcamsrs of these cheap cleaning lasers! (not ALL Chinese lasers are bad, but do your homework)...most of these thing are 'toys" 1. Avoid anything with a Raycus laser diode (they are getting better, but there is a reason why they are so cheap...most won't last a year...) 2. Don't get a unit that cleans AND welds (they do neither well) 3. Get a unit with USA tech support (from a dealer....avoid Amazon/Alibaba, or you WILL be sorry) 4. Get a unit that has a chiller for the diode (for a continuous wave laser like the one in this video)...pulse wave up to 300w is ok without 5. Make sure the head has an air blade (keeps the protective lenses cleaner much longer/ extends optics life) 6. Continuous Wave lasers are usually the way to go (unless doing thin material/ Aluminum / heat treat scale)....then go to a pulse laser 7. Don't use they eyewear that comes with the laser cleaner (they are always OD 5...should be at least OD 7+ @ 1.0 - 1.1 nm range wavelength) 8. Don't use welding goggles as eyewear (totally different wavelength...won't protect eyes at all) 9. Bescutter is probably the best entry level cleaning laser / bang for the buck...has a 2 year on sight service warranty 10. If USA made cleaning lasers are in your budget I'd recommend Laser Marking Technologies (1/2 the price of the big boys with better core and optics) 11. Ask for references....folks who have been using them for a while will be glad to share the good, the bad and the ugly

The chisel is a quality tip. Not only is it safer, it's easier to do with lesser tools. Thanks for the instruction video!

Great video, thanks

I have two drips on the basecoat. How do I get rid of them?

$100 in materials and in 5 hours you could have a 60 amp circuit to run a 240 volt welder.

Thank you for this video. I have the skills to do all this but just didn't know where to start. 😊

what brand is the sanding block? Any idea where they sell them?

awesome technique. What is the half round metal block you put down?

When you spray it must look wet when spraying.Spray painter.

Should have used a needle to clean spray nobs.