Video

Do you have a video showing exactly how you remove the block drain plug? My O2 sensor blocks my wrench

Are all manual e36 pedal boxes the same? (eg 318i and m3)

Do you know what happened with this track? Such a tragedy its not fully operating. :(

i also face this problem but after i adjust the wiper arm when i open second or third speed of wiper it will hit the windshield side seals😢

Is the manifold from a 1995 E34 M50B25TU the same manifold?

Can you pass CA smog with this ?

Hi i have a question on the passanger side there’s big two round plug and what are they?

Deadass saved me so much $$ just following these DIY videos. Thanks bro👍🏼

So what is the clutch switch used for and also my auto has cruise control am i being able to still use it after the manual swap?

Was looking for ways to make the poly mounts for my RSX less harsh, last thing I was expecting was to stumble across Quinn from throtl personal channel lol

How come you didnt just change the lower guides since you had it out

You are amazing brother Not a single video speaks about the in and out stamp even google just says arrows Cause I am having fuel problems and i thought i put the filter on wrong

If the chip is not removed, will the speed be limited? I swapped engines and manual transmissions (m44b19>>>m52b28) Currently, the top speed will falter when changing gears.

My uncle has a 1993 sedan

A $50 Creator code reader will read BMW specific codes

thank you sir 🤘🏻

I followed your posts when I fixed my original blown head gasket 12k miles ago. I did not see this video. I ran the Cometic mls gasket with ARP studs. I did not get the block machined and just like you said #6 cylinder started leaking coolant. I’m running 9-10lbs boost from a VF supercharger. I will now be redoing the work 2 years later. Great vid. Thankyou for the info. even though it was too late for me..

Hey Quinn, really helpfull video. I have a question, there are two of these rubber ball joints on each side? I mean, i saw in other videos that in non M cars the Upper one is a "solid rubbererized" one and in those videos i think they mentioned that you can replace them for the one that you show here as an upgrade. Is that correct? (Edit: Pretty sure i may be mistaken with the lower INNER control arm bushing) Edit: I saw the second part of this job in your other video. Got my answer there, lol. But now im wondering if thes things have an orientation or it doesnt matter the way you put them. (In the mentioned videos they say that these ball joints have two lips, one flush and one more rounded. The one that's flush should be pointing towards the front of the car. Can you tell me if i should pay attention to this?

So, can or should i disconnect the tension rods when converting to a full manual?

Will ms41.1 with ews delete from kp fire right up without doing any ews wire mods? ✂️ car is 1997 e36

how old was you here quinn ?

clockin views here years later

Surprised you didn't weight balance these. Like jewelry.

Till this day...these videos are still helping the e36 community. Thank you for you service Quinn!

Awesome, thanks!

At 8:19 mins on the vid why did you use wrapper when putting In the part were the cams sit in

Where do you get the manual latch?

mine blew up 🥲🥲🥲

Hi man I'm having some trouble doing this can you help me out?

this was so helpful thanks!!

No need to program right?

8mm bolt

What about the starter mounting brackets? Every video seems to skip over that..

would you know or know where i could get instructions to fit the convertible Top push Rod Pivot for my 325i E36

Very nice video. Well documented and thank you so much for no crazy camera shakes and music ovelay! Question: you tighted the thermostat housing for the aluminum kind at 89 ft-lbs! Just confirming things, per the manual, which is for the plastic housing OEM, its 10nm (7.3 ft-lbs) just confirming the differences because of product material. How/why 89 ft-lbs?

💪🏽💪🏽

Excellent tuto bro Where can I find the silicone hose?

3 years later and still helping new e36 owners thank you❤

Which one to use when you have twice a number ? Same price but different reference

Wait what do you do with the cable that goes to the steering column??

Should have just used ms41 quick flash and rom raider

I know ur doin MUCH bigger things but this channel was SO informative. Miss ya quinn. When u reroute that coolant line from the throttle body do u need to bleed the coolant system?

On an european E36 its a T27 and not T25

Insanely good video 5 years later immediately got a like and a sub

SOOOO THIS IS WHERE QUINN STARTED NICE

Thanks!

where the catch can is plugged to ?

YEAH!!!!!!!!!!!!!!!!!!!!

So once connected to adjust it correctly I need to run it 10-15 minutes to reach some temperature and adjust it? I have a s10 2.2 it was fan clutch so I buy this to do it electric fan. I think the temperature normally if like 195 when I see this if when I adjust?

bushings and ball joints are different especially in that a bushing has virtually a 1 way movement and a ball joint has polymovement, axial movement, it helps to use correct terminology when ordering parts, good job finding it .. I think ther are 3 points on the rear suspension that need to be checked, upper control arm, lower control arm and trailing arm..