Video

Rip dock 😭

looks like it were just a few inches from entering the house.

What holds on the head unit to the water softener? Mine just sits in there. Seems like it should have a clip or a locking deal. Just picked it up at a garage sale. Any help would be awesome.

I have a problem with the water ‏continuously draining! What is the solution?

For the hardness... the system defaults to 25 what? grains or 25 parts per million?

Hello, Is there only in gallons way to see on the screen? Can i change for litres? And i really cant understand the set up for qubic feet 1:00 - what should i declare in this place? Could You please help - i cant find explanation in manual form Pentair corp.

You mighta just saved my ass

During back wash how many minutes

Thank you

Thank you for this! I bought an injection head from someone on marketplace and couldn't figure out what was going wrong until I found out I was using an air injection valve, and not the regular, but I didn't have the money to buy another head unit. Thank goodness I found your video!

Hello is there a way to contact you? To ask questions

Can you explain how a (Fleck 9100 sxt digital water Softener controller ) works?

How do you adjust the conditioner for hardness?

EXC video, well paced, clear! TY

Hello Andrew. I’m having a hard time finding out how to set up this controller… we have less than a year living in our home, and we had to clean the septic tank twice (and a week later is already full of water again now). and I had local softener companies here to get it checked, but they are just interested in selling their system, saying they don't know how to operate this device. So if you please can help with it showing a video. That'll be amazing. Thank you.

Wohoho, Andrew’s on fire! 🔥

Andrew’s the GOAT

Yeah, but how do you remove that basket? Looks like it goes on easy but trying to remove it is a whole other problem.

You did a really great job with this video. I watched another video first where the guy said, "depressurize the system and then...", but he never said how to depressurize it. Chances are that if i already knew how to do that, i probably know how to do the rest of it. Thank you for being detailed.

All O rings go in the valve cover. The O rings on the cam did not seal correctly as installed on the video. Fyi

My softener was draining constantly. I closed the bypass and opened the valve assembly. All the Orings that you are replacing are present and accounted for - the figure 8, the one on the drain plunger, the 2 on the rotor, the large on in the cap. The problem is that I found a 1" Oring broken into 5 separate sections. 2 were under the drain plunger, and 3 were on top of the drain plunger. Where did this 1" Oring come from? It is not part of the seal kit. I wonder if it is out of the bypass valve, but that is working fine with no leaks when open or closed. Any ideas? I will replace all the ones from the kit, but I fear that the machine will not be functional if I don't figure out where the broken 1" Oring came from and replace that one too!

Thank-you, well done and very helpful!

Wow...this is sooooo much more of a pain in the a$$ than the old design !!!! The old style SIMPLY had 2 screws that made changing our the timer motor a TWO MINUTE JOB !!!! Whoever designed and approved this new method for change out was a genuine DORK !!!!! There is ZERO excuse for making what was a simple and no-risk TWO MINUTE job into this TEN minute , parts-loss-risking fiasco...I am STUNNED at the brazen stupidity of whoever designed AND approved of this type of motor change !!!

Very informative. Thanks for posting

Where do I start troubleshooting if my drainflow is releasing water constantly? Also sounds like a pressure leak noise around the meter assembly w/condensation but cannot feel a leak. Is it stuck in regeneration mode? Can’t find a video for this problem. Thx.

Where can I get this item

Can you do this with the water softener in bypass or you have to turn the whole water off?

I got the back off the 5600 and can see the see where the cams engage the plunger. So at what stage looking at the back whenever the plunger is depressed should suction start right away?

With the button out wouldn't it be better to turn on the water and flush for a few seconds before putting it back on?

So thankful for this video. The manual says nothing about this at all. Very important since my new unit did not have this installed properly. The retainer was in about 1 thread deep and the button was flopping around behind it. I was wondering what it was for when trying screw in the pipe fitting. I surmised it might be some kind of flow control or maybe a protective dust cap for the button. Just wanted the stupid manual to say so instead of guessing. Thanks so much for this video and leaving it so that 8 years later it helped someone like me. Bravo.

My GE water softener slowly drips out the drain line in service mode. Could it be the seals causing this? It's only 2 years old.

Sompinsgotsto give

Thank you sir that was helpful.

Thanks for the info.

At 4:00, your comment about the o-ring was the solution for my issue of a properly working system but no soft water. I did not find anywhere else on CZcams or install manuals about making sure the tube is inserted through the o-ring up into the valve head. Thanks! Also, those water hardness test strips are junk. The Hach 5B Hardness Test Kit is essential.

I did this to my , thank you, I do have a ? Should it be hard to turn cam gear by hand once’s tie down , does it loosen up once its under water pressure, its seen hard to turn or did I do something wrong

Where can I buy GE softner parts. My motor is broken and need a newer one but all the vendors have the medal instead of the plastic versions?

Thank you sir!

Thank you so much for making this video.

how to fix cam gear no stop?

Why don’t you show the back as you give instructions?

Thank you for the video, Andrew. Very helpful. However, I can not locate a single video of someone *removing* the CAM. Your video shows how to install it but is limited to how to line it up properly. It seemed like you edited out actually getting the part fully seated in position. I've tried everything to remove the cam and it won't budge. Anyone have any suggestions?

When I got down to the seals, they were covered with water. I didn't see that in your video. Does that mean I have a problem other than the seals?

I have a 440i that is not backwashing, no noise. It seems to be going through the process mechanically but no sign of water flow.

My Tapworks AD11 looks very similar to this. The motor housing the series of cogs had cracked and the cogs had become misaligned. I tried turning the cam by hand. Boy was it stiff. Useful video thanks.

Thank you for this informative video. I feel confident enough to do this now myself!

Is this for Whirlpool WHELJ1?

Ciao il mio logix sia programma sempre. Ha batterie?? Posso sapere come si sostituiscono??

Why is my softener re generate at mid day

Lifesaver! You have saved allot of people allot of money im sure. Thank you!