Video

High precision machining

My mixmaster died and the sunbeam service center told me it cannot be repaired. It turned out that my thermal switch was burned up and it is not resetable, I replaced it with a self reseting thermal switch and it works like new again.

A impact gun and some deep well sockets would have made this job 50% easier. And no torque wrench to torque the nuts to the proper specs?

Anyone have a part number and correct name of the retainer clip for beaters? The mixer I am working on the one beater keeps falling out.

Great video and great information

Can you install this on hard drive?

Thank you. That fixed it. Having gone in there to fix the mixer, my guess would be that the magnetic on the ring weakens in its magnetic field over time. This combined with the obscenely large air gap results in a poor signal being sent to the control board. By pushing the sensor closer to magnetic ring it reduces the air gap and gives the speed sensor (a hall-effect sensor) a stronger magnetic field to read. Thus in turn giving a better signal to the control board. So again, thank you.

Could this work if only one side is spinning ?

Thank you this did help me

I am going to gloat for just a second and say I felt a little bad for you fighting with some of those fasteners down here in the south we don’t have rust or corrosion like that

Most AC motors are reversible! Just because there is not a reverse switch on there does not mean it's not reversible. Many AC motors have a diagram on the motor showing how to reverse direction of the motor. Some really are designed not to be reversed. You have to take the windings out of the case and hook them up differently and put them back into the case. There's a video on those also.

You can also put a double pole double throw switch on that drill press right where it connects to the capacitor! Even a regular residential 4way wall switch also work. That's what I used on my drill press. A four-way wall switch will change direction but it does not have and off position. You can add a regular on and off switch for that purpose.

I sometimes use mitrax very interesting little operating system. Always wanted to install it on USB drive. Thank you John it is now on USB drive. All I have to do now is get printing going.

Only one of the attachment works. Only one spins.. don’t know what to do…

Can you please put how much you added in cups or grams of flour

Thought you were making rye sourdough you only put it in the starter

Bendiciones para su vida gracias por dar información como se aregla una batidora, le cuento que tengo una batidora sumbeam mixmaster modelo 2395 y con tiene 12 velocidades y le cuento que cuando la enciendo no le funcionan engranajes de batidora sumbeam espero que me diga como la puedo areglar los engranajes y me lo puede traducir en español para poder entender bien hoy es martes 3 de enero del 2,023 les deseo un feliz año nuevo muchas bendiciones para todas su familia aquí son las 11:44 AM.

Always unplug before opening .....

Nice😀👍

Very good

thanks

The sway bar links were the biggest headache while changing my struts in my 2008 Malibu

What brand did you use and did it last?

just what i needed mixer works like new now . thanks for the share

How come the arrow has to be towards the engine is that a critical thing or is it just the way it's done ???

Great video

Thanks for this video. Couldn't figure out how to get into my 2594 Mixmaster and this showed me. Just wish my plastic front cover snapped on/off as easily as yours. I thought I was going to break it both times. If some ambitious Chinese place wants to clone those plastic worm gears for the beaters, I doubt I'd be your only customer. Thanks to one of them, my mixer is now a paperweight. I don't know what good it does having sacrificial plastic gears there if you can't actually obtain one when it breaks, but I guess we're not supposed to be going inside the crap anyhow. Take Care

Yeah, why would you want to add yeast if this is a sourdough using wild yeast. Sourdough is more healthy. Anyway, thanks for your time in showing this video.

It looks much better than the first video!!!

Thank you for the simple explanation of each step. I got stuck on the upper nut of the Sway Bar link. I had to purchase a T-40 tip to prevent the bolt from turning. My second problem was removing the rusted plate holding the brake line (located towards driver). I noticed you removed the rusted plate with bolt pushing it towards you. Will continue tomorrow. Wish me luck. Laters. Stay Safe My Friends.

Спасибо.

hi There are 4 of these pieces, which one needs to be changed, thanks

There are plenty of recipes using the bread machine, adding both starter and yeast. Then it’s done start to finish. No need to do what you are doing.

This can be done all Sourdough, no yeast and if measurements were done correctly, it could work. I will experiment this. After mixing on “dough cycle”, stop cycle and let dough ferment 6-8 hours. That’s the bulk fermentation. Start machine, “dough cycle”, just to collapse dough. Then do “bake cycle” with a 3-5 hour delay. This is to proof and it goes into bake. I’ve seen a few of these videos, but none do the whole method to bake using the machine. It might work. I’m a home bread baker and make sourdough the manual way.

What is the measurements of the scoop please?

that bread sure is soft 👍

Beim zusehen wird man nervös

How did you open the curling iron?

Might be a good video, but no measurements for the important items like flour, water and starter. One half jar of starter? More water? I bet there are different size jars……..lol!

Very well presented.

so its better for buy cnc shield v3?

Thank you sir great video

That's a good idea. Just put an on and off switch in the circuit that goes to the start capacitor. The cheap Westinghouse motor on my drill did not have a start capacitor, nor did it have any wiring directions or directions for reversing rotation. Check where the power wires go inside the shell and see if there are wires to reverse that come out of the windings. if there is you might be able to reverse the direction of the motor just with a switch. This guy knows a lot about reversing motors. czcams.com/video/__nS3OelY-s/video.html

So no torque specs needed?

Nice, i ll do the same on my current cnc and see how it performs. Good video

good mini cnc check

Are both bays read-writable over USB? Or is the second bay specifically for just cloning?

GRBL version?

Thank you dear friend! You saved my CNC. Congratulations on sharing your knowledge ...

Me gustaría que las instrucciones estuvieran en español