Video

Words to the wise. I know this video is 3 yes old but I just had to add something. Anti seize is fine for threads and things that don't move unless being adjusted. Things that move as a normal part of the suspensions action should use grease. Antiseize isn't a particularly good lubricant and will accelerate wear.

What coating is that?

220 volt welder?

Man it’s my first time watching a video buddy

Yup

Hell ya!

Beautiful

Looks awesome! Nice work.

53 Pontiac...hood won't close...hinge side stays up

What size rims will clear the calipers

So yall ran out of storage for rear install

Is that a sock on your shifter?

Cool!!!!!

Awesome project

That’s crazy I just bought one, 2 days ago , same two tone green and everything,, great job, that thing looks slick

I gotta say you got one sweet ride. Absolutely love it.❤❤❤

Nice

Beautiful Saturday night

What a/c system you installed vintage air?

Ruined it with the hellcat v8 and those stupid wheels

Intwresting paint on this thing...;)

What size upper pulley are you running?

Ordered!!! Thanks

Can you share the link to the stuff ??

how hard is it to pull that dash? Would have been a million times easier to wrap that sucker outside of the car. Looks GREAT though... totally dig it

What PCM are you running?

I would've just went with dual fully adjustable coil overs for the rear.

Fantastic work and great videos. Currently sourcing stuff for my 51 Pontiac and still on the fence for the automatic or manual transmission. Earlier in the video you mentioned about taking measurements to make sure the trans tunnel area was big enough to fit the transmission (assume 4L80). Was this the case or did you need to make additional modifications to the sheet metal in this area? Thx

A question the struts come with the spacers? Or you buy separately?

Nice ride! Is it sitting on the original frame? If not what frame is it sitting on?

Should have at least 5 to 10 degrees poss caster!!!

I think my 54 truck mounts are different. Do you know if anyone has tried this?

I am looking at that same set up for my 70 c20. any chance you got those part numbers to piece this together for cheaper? Thanks

Yep definitely nice finishing touch 👍

Can i order one? How much?

I'm evidently not good at searching for this on eBay. I do not see anything similar to yours or that I feel might work. Do you have a link to what you used that you could share?

get the bluecat transmission software if you cant find it reply with your email and Ill send it.

ok when can I drop my car off?

I'm definitely not opposed to rustoleum as a basecoat but that clear is not gonna last. Next time i would suggest scuffing with a grey scotchbrite or 800 grit wetsand. Then apply a adhesion promotor since its a raw plastic. Try a flat or satin rustoleum black then use a 2k clear from a can or a paint gun. That shit will last for years.

When did male supermodels start painting car parts in their driveway with $3 paint cans? Problem with (most) aerosols, they basically fall off if a can of brake clean is within a city block. If you want real paint in a can, try some SprayMax 2K stuff. Just wear a respirator, this shyte will turn the frogs gay.

look good

Don’t stop.. these posts are getting me horny

Deutsch connector is too small... Rated for 15 amps odd problem though

Drag truck would be cool. Just put a 80mm turbo on it!

Lesbian Subaru!! HAAhahahahaha

Nice work man... 4 day swap by yourself rates.... Truck looks mint too... sounds good and looks like its got some go...sorry to hear about the rear main...its an LS thing and we ALL understand

All that nonsense for that? You would have been better off throwing a carbureted Big block in the thing 🤷

Shoulda went with the 5.0 Coyote!!🤷

How are you handsome built and have a scsb my wife sees you and I’m gonna be upset 😮‍💨😂

The turning of the strut 180 degrees has got me a bit confused. Why can’t we just turn the top hat 180 degrees? Isn’t it the same, but easier?