Video

I wonder why the filament after the glue gun won't break. There is the zone where it is getting hot and the force must be very low here.

Sir how much cost of 3d printing machine

Oh snap, I wonder how well this would work with scrap pla from the suppotrs

Got the files for this?

Mast yaar keshe kiye he

Um problema de sustentabilidade resolve o problema energético?

This has been the best one of these Filament recycling videos I've seen so far. You took the definition of protrusion as literally as possible

Nice tool repurposing. Is it me or is that contraption saying, "help me!" Over and over again?

I like this "take what you have" setup, probably more affordable than buildning it with dedicated circuitry and motors, although the accuracy of the oull might be variable depending on the load of the screw driver motor

Just a tip if youre planning on making this, you can skip printing the gears from the roll and directly put the motor to the spool if you add a PWM module to the input voltage of the dc motor. That way, you can reduce the speed of rotation of the spool and use less filaments for the structure and skip the gear ratios 😊 Adendum: you can even add a potentiometer to the glue gun so you can adjust the temperature

Sounds silly, but if you lubricate that blade with a bit of wd-40 not the best cause it’s not a lubricant but motor oil or even olive oil. It would cut sooooooooooo much smoother

What is the lowest temperature you can print this at…..i have a K9 that only goes up to 230

Extruder : 100€ Glue pistol : 5€ Genius

I think it's fake! U can't pull there wire so strong while it's warm. And the second is that the bottle don't move and the filament from the bottle also don't move. It's an "to easy" set up.

Are there videos where do u print with the filament?

The bottle is still wet :o how does it print because most recycled bottle prints like shit

Genius use of the hot glue gun but wouldn't bottle grade pet be bad for prints?

i have the same problem of making a nozzle thats hot to string the bottle.. this is genius haha

UnStopable!!! That's the perfect song for you. My respects!!!

Are you making your own 3d Printer?

That is so cool!!!

Beaitifull

From where you got your 3d Models?

That's how you make the nozzle?

You deserve a BAMBU LAB

Amazing

I you got the nozzle?

Is this work

Je pense que cela ne va pas fonctionner longtemps. ou pas du tout. Le filament en sortant du pistolet est mous, limite en fusion. l est impossible de tiré dessus sans que cela ne se casse! Même si refroidi en sortie

How good is that water plastic? Is it as strong as p? L? A.

My friend, your content is excellent, but can it be done with a 0.4mm nozzle like in your setup, that is, can 0.4mm filament be produced?

i imagine its being pushed through and not pulled or it would snap at the hot part

bro we all just have this contraption lying around

la hoja de la sierra esta al revez

How did you get it through the hot glue gun???

This is what I like to see. Not spending $100s on a “specific tool” and instead using something cheap that can do the job just as well

how much watt glue gun is it? 40 or 60?

how many watts needs to be glue gun?

God

what size doe it come out?

Completely safe... lmbo.. no thanks.

오😮 저런 아이디어가?

is this a high temp hot glue gun or low temp hot glue gun?

nice, gotta appreciate the dedication

Tooooopp0p

Where can i find the stl file for the gear box?

Where is the build list in long-form video?

One warning: The End of the filament is hook shaped to hold it on the spool. If your filament runs out mid print, the hook will prevent the filamentrunout sensor to detect that. This results in a faild print that takes considerable effort to recover from, if successfull at all.

How do you start it, how to feed the plastic into the glue gun so you can spool it up?

ok, i did however find a $12 nozzle, but this clerarly shows the process.