Video

That charger is now 3800!

liked you're fiber glass work ( :

Thanks for that ours is leaking the same but now I am thinking we gotta clean the whole thing instead of just replacing a washer 🙄

Well done

Danke, das war sehr hilfreich. Liebe Grüße aus Germany, Ela& Frank.🙋‍♀️🙋🏻‍♂️

Man, I thought rv maintenance was an ordeal!

Well done. Very easy to understand explanations.

Hi again, I notice you have anodes on your rudder? I’ve never seen this on any other Super Maramu’s? Usually just the 2 anodes on the rudder as the keel is connected to those via the bonding strap in the bilge.

Hi Woody, can I ask is there a reason why you shortened the pole from the end that takes the sheet, rather than the end that connects to the smaller jokey pole?

I have this same job to do, but forward where the eye bolt is for attaching the block to where the pole fore-guy connects. Would you say that G10 board I’d strong enough to tap and the bolt hold there?

Thanks!

Thank you. I’ve just bought a new me boat and there is a 25lt version to check over.

Please tell us you did not use welding cable. They are NOT suitable for marine use

Thank you!

Buy a new toilet???

Many thanks. I'm just about to go through this whole process and found your video. I feel a lot more confident doing this now. Cheers from Sweden 👍

Thanks!

The 3 pole 40 amp circuit breaker you put in between the AC Outlet on your inverter & the load, was it a AC or DC circuit breaker?

Woody, arent there big cable exiting the engine room at the floor and mid way up by the filter? But, then they are all in the cabin step... how do they come together? I am trying to route the WS500 cables and am afraid of hitting one of those big cables.

FYI the type of thermometer you used to check the thermostat cannot give accurate readings of liquids or wet/shiny objects.

Buenos días Cuando se monte manguitos o tubos de goma tanto de toma agua salada o dulce, sobre hierro de fundición o aluminios debe de ponerse grasa en las toma de agua y así conseguimos no se sulfate o oxide los materiales, no debe de hacerse en tuberías de presión superior a 3atm

Best video on CZcams showing cambelt change on Volvo MD22, Volvo TMD22 / Perkins Prima. Thanks very much for uploading this video. Also good to see it done without any special tools / good mechanic.

BUEN TRABAJO CAPITAN SALUDOS DESDE LATITUD 34 S. ARGENTINA Y BUENA PROA !!!

We kept our old water lock from our Onan generator! Just in case anyone wanted one!!

So much extra work due to a simple seacock mistake. I hope it works out in the long run

Thank you, great video, but I find the language difficult. I hope that if you have time in the future, you will bring these elements above the long one, how they are connected to each other and their role in cooling. I am weak in English.

Ka-Ching. More money 😮

hello mate from the other part of the world :) some suggestions from me :) 1 make another sea cock to have the genset separated and easily used for the main engine in case of emergency ;) 2 see if you can manage to rig that stop solenoid to the alarm system as this could have been easily avoided , that onan is equipped with 3 shut down alarms, low oil pressure , high coolant temp and high exhaust temperature, these only work if the system is connected to a functional shut off solenoid :) if that is not possible to fix or too expensive (ask me how I know ) you can always order a temperature gauge with alarm and install one on the exhaust and another on the engine coolant , whilst you are at it an oil pressure alarm and its all set , sure you can find on ebay or aliexpress etc , keep it up and if you need you know where to reach out :) fair winds and say hi to all :)

Easy error to make. I've done something similar and now always hang a key or a tag on the start switch when I do anything to the engine so I know to check everything before just mindlessly starting it. It doesn't always work with new people who might not realize what the tag/key means but at least you will get a bit of a reminder. It's saved me from having to McGyver in remote locations (which you are exceedingly good at). Glad you got it sorted out and that you didn't have to dive in Salty infested waters to find that adapter!

GRAN TRABAJO WOODY !!!! MUY BUEN VIDEO !!! TE MANDO UN GRAN SALUDO DESDE ARGENTINA

The only issue to be aware of, and I am sure you would know this is condensation on the outside of the freezer when in warmer climates, they just don’t have the amount if insulation that your old fridge did.

Para tornillos se caen muchas veces y no se pueden sujetar para colocarlos, tener plastilina, se utiliza en manualidades de los niños, no arcilla

Thanks!

Great video. However, as a plumber you should wear disposable gloves when working on the drains. It is calcium, but also contains bacteria from pee and poop. Any cuts on your hands and you risk an infection.

Thanks!

Thanks

Great JOB.... Hope you guys have a smooth sailing forward, with lots of cold beer.... Ken

Thanks!

Thanks

Is the cabinet well enough ventilated for cooling efficiency?

Excellent video well done. 👍👍

Great job…. Told you it was knackered 😅

Another great video ! Good timing as I’m thinking of doing the same thing for my 1983 Westerly Sealord. Existing ‘cool’ box works ok ish but draws about 60 amps and is really noisy. Any idea on the power draw of yours ?

Thank you, your video was helpful for locating the bolt to tighten up the belt.

My brother had a 1959 Johnson 5hp, and it ran great. He gave it to a Man who had a young family and he still uses it to this day!!! By the way, reverse was instituted by turning the motor 180 degrees.

Thx! +++

Brilliant....If you're passing my way.............

It's the hard way and it's the wrong way to clean out the toilet tube. My tube is 1.5" and 6 meter, i cleaned it out in 20 minutes using 30% acetic acid.(Keep the sea water inlet closed while doing it, after putting 6 liter inn little by little and taking my time I flush it slowly out using cold fresh water(no seawater) septic hose should never be near heat and you should never throw hot water in it.

Tuto duper bien fait merci

Man do you have the room to work on this... I am looking to rebuild my TMD22B as a replacement D2-75 is around $18,400. I am concerned about how much live the heat exchanger has left on it as it was installed around 1998.