Video

Edgelords unite!

Thank you.

Thanks for this video ❤

There are quite a few good teachers on youtube. Thanks for the video

You are the best. You explained it very clearly

steve thank so much. just a couple of shots of wd-40 in the provided slots on my 2012 craftsman 25cc mini tiller worked the pullcord and within 30 minutes its snaping back like a champ. must have been dry with some rust build up.

My mower is leaking oil & the oil spout is dirty how do I do a oil change on my mower

Best ever chainsaw sharpening tutoria! Your edge over competition helps by detailed close-ups & giving viewer the comparisons of right vs. wrong. Congratulations!!!

Autocut 5-2 may not be the same thing as the C5-2, but they look the same; and the manual puts the spring in a different place; just worth a note here: go by what it says in the manual?

Works for separating 5 gallon buckets too.

It USED to be easy, but at 72 it's not as easy when I was 20 yrs younger and could manhandle a lawnmower.

I used the shaft of my 11 in one screwdriver that has the hex tip

Great demonstration, especially for a first timer.

It totally worked for me🤣

Thank you for all the tips,very helpful now I know how to do it ,great video👍

A very good video. I have a Troy-Bilt TB360 and I was cutting under a bush, when the RPM went down on the mower and it did not increase when I pulled the mower back out. Is there an arm on this that might have been bent by hitting a branch?

I've always used alcohol, but after seeing the pressure washer handle, I'm moving to air. Thanks.

Not hidden at all. Dumbass owners have no clue it's there! 🙄

Do they make a Metal replacement for these?

thanks Steve for that info, I never held the bar up when I tightened the chain and noticed it would get loose really fast!

Thanks again Steve. Seriously, for the 20th or 30th time, you’ve given me some very useful knowledge.

‘Tooning’ and ‘toobs’.

What about larger decks one on left and one in the centre?

Don't know if it would work for those since they're stiffer, but bicycle handlebar grips go on super easy if you lubricate them with some PVA glue (common white wood glue). They slide on really easy, then stick firm once the glue dries.

Cheers 🍻

Thanks for your help to solving those problems with the bearings and spindals . It sure makes sense to me.

Oldest trick in the book

Sound advice Steve 😂😂😂

Thanks!

Well I'll be jiggered !

Yeah 👍 Steve!

Thanks for your tips! I'm embarrassed to say I sanded my flywheel before watching this. Never again.

Video said no tools. What did he use to remove the spark plug

I would say it has to be from a bad fuel mixture. It’s expensive, but I run stihl’s motomix in my KM130. All the rest of my other stihl 2 strokes get premium gas and stihl oil, but my 4mix gets motomix.

A lot better and easier way to clean the bottom of the mower deck is to first scrape the bottom before the first spring use. Then spray the bottom with an aerosol can of vegetable oil. The mown grass WILL NOT stick to the bottom side. Spray the bottom side with oil before each mowing. TRY IT, IT WORKS!!!

damn, now you tell me!

Wow, glad I watched. Had no idea. Always flipped it over on it's side.

I always used a few drops of gasoline. it worked well also.

That is an awesome tip. Thank you Johnny Walker . You sure that has nothing to do with the Whiskey? Mike from Mass.

Steve, does the governor mechanism fail on the inside of the case very often? Ive got one that just wont adjust, it wants to race no matter where set? Thank you.

This also works with 5 gallon pails that have been stacked together and get stuck.

Not one of these people would have contact the lady and gave it back….but they wanna see you do it pssssss

Keep it

You just gains a like and a sub. What a great video. Simple easy step by step troubleshooting. THanks :)

Hey Steve, I would have liked the video if you could have just used a cordless impact and quickly opened it up and showed us the crank rod but that one shot through the muffler man. I really feel like I wasted my time. I honestly would have liked and subscribed if you had broke it down.

Top notch, Steve.

A buddy just gave me his weed eater because it did not work anymore. I opened the side and saw exactly this and asked out loud "WTF is this crap?" Seriously??? How cheap can they go?

I am quite amazed that your tip was actually worthless. It doesn’t matter what speed I have my idle set on when I disengage my blades. My timing belt still pops off the minute. I activate the blades within 10 feet of mowing, timing belt jumps off.

My mower is pressurizing is the gas tank, sputters, quits. Put on side to change oil and gas leaked out of carb and ruined filter., replaced oil but now won't run well gas bubbles. I need a mechanic., I messed it up. M320 CRAFTSMAN just bought it last year., hit a rock today bent blade at a 45 degree, and then it was smoking. Any help with those bubbles? What's clogged? and what do I do?

Thank you for the great tips. I just my JD used and will have to look into this ASAP