![TylerThePlowGuy](/img/default-banner.jpg)
- 28
- 173 893
TylerThePlowGuy
Registrace 23. 08. 2015
Tips and Tricks concerning Vintage John Deere Moldboard Plows.
John Deere plow bottoms and how they attach to the plow.
Explanation of how conventional MP312 plow bottom attaches to the plow beam. Newer john deere plow bottoms can interchange by unbolting and reinstalling; usually with only 4 bolts.
zhlédnutí: 674
Video
John Deere HS plow bottoms explained. How to tell if you've got a 14 versus 16 inch High Speed
zhlédnutí 11KPřed 2 lety
So much confusion about the difference between 14 and 16 inch HS (High Speed) John Deere Moldboard plow bottoms. How to measure the plow frame and what to look for when seeking out replacement parts. 3 versus 4- bolt plow shares explained.
John Deere 430W pulling One bottom 22 plow Syracuse bottoms
zhlédnutí 1,4KPřed 4 lety
First time out with the 22 JD one bottom plow after rebuild. Weights on the frame just in case as it was very dry.
John Deere Safety Trip Standard shim adjustment part 2
zhlédnutí 2,5KPřed 4 lety
Pertains to mechanisms used on models included to: 415 416 415A 416A 810A 444 45 F45 F120 F130 F125 F145 810 415 1250 555 666 777 F620 F630 F650 F660 F680 F690 825 845 4600 4200 How to adjust the throw-out link once shims are changed or when reassembling for overhaul & restoration
How it works....John Deere Safety-Trip Standard used on moldboard plows
zhlédnutí 4,8KPřed 4 lety
How it works....John Deere Safety-Trip Standard used on moldboard plows
Wapsi Hydraulic Conversion on John Deere 4020 tractor
zhlédnutí 47KPřed 6 lety
How to install a new Leak Free Remote Coupler Kit from WAPSI Innovations. This applies to John Deere 20, 30, and 40 series tractors. Some of the compatible models: 1020 1520 2020 2510 2520 3020 4020 4000 4320 4520 4620 7020 7520 1530 2030 2630 4030 4230 4430 4630 6030 8430 8630 2040 2240 2440 2640 2840 2940 4040 4240 4440 4640 4840 8440 8640 Wapsiinnovations.com
John Deere Enclosed Clutch Rebuild
zhlédnutí 5KPřed 6 lety
A step-by-step guide to rebuilding the enclosed type clutch on John Deere moldboard plows. This includes models: 51 52 53 4B 4C 4D 22 22A 22B 44 55A 55B 56 57 some disk plows and some listers.
Deere 66H plow wheel bearing installation
zhlédnutí 1,6KPřed 7 lety
John Deere Moldboard plow wheel bearing explained. This is a John Deere 66H series moldboard plow land wheel.
John Deere Coulter disassembly D673A type
zhlédnutí 2,8KPřed 7 lety
A quick how-to on coulter blade / bearing removal from a JD D673A yoke type coulter. This was done on the plow while still attached. Always wear safety glasses and gloves to protect yourself.
John Deere 720 Diesel plowing 810A Special Trash Plow Slat Bottom
zhlédnutí 3KPřed 7 lety
Plowing Fall 2016 Near Shiloh, IL in loam.
Plowing October 2013 Longtown MO with late model A and 202 two way
zhlédnutí 3KPřed 7 lety
Plowing October 2013 Longtown MO with late model A and 202 two way
How to protect your plow from rust when done plowing.
zhlédnutí 5KPřed 7 lety
How to protect your plow from rust when done plowing.
John Deere 720 Diesel and 3 bottom plow 2016- All Smiles
zhlédnutí 1,2KPřed 7 lety
John Deere 720 Diesel and 3 bottom plow 2016- All Smiles
630 and F130 3x14 plow at plow day 2016
zhlédnutí 9KPřed 7 lety
630 and F130 3x14 plow at plow day 2016
1958 John Deere Diesel Electric Start row-crop with 4-14 F690H JD plow
zhlédnutí 1,8KPřed 7 lety
1958 John Deere Diesel Electric Start row-crop with 4-14 F690H JD plow
How to get that shiny moldboard (scouring)!
zhlédnutí 9KPřed 7 lety
How to get that shiny moldboard (scouring)!
How to take Drive Wheel off of a John Deere Enclosed Type Clutch Lift plow
zhlédnutí 9KPřed 8 lety
How to take Drive Wheel off of a John Deere Enclosed Type Clutch Lift plow
John Deere Plow, Axle Bearings, When to replace, What to look for, How to Fix
zhlédnutí 11KPřed 8 lety
John Deere Plow, Axle Bearings, When to replace, What to look for, How to Fix
Listen to that 31HP 430W Snort!
Great video! Thanks for sharing. One safety trip on the forward most bottom of my 3-bottoms e-8450 plow is not staying engaged and immediately trips back when moving forward again after hitting a big rock in my field. On quick inspection, nothing looks bent or broken or different than the other bottoms. What would you suggest I look at next? Thanks!!!
That work for 5020's as well?
Thanks for the video! I have only recently started participating in some of the local plow days in my area. I am in the process of purchasing my first mechanical trip plow which is a Deere 55 plow (not sure on exact details of it yet), but it is a clutch trip. I was very hesitant on getting a trip clutch plow and/or converting one to hydraulic since my red tractors do have hydraulic capability. But thanks to your video, I now feel completely comfortable keeping and maintaining the original clutch system on it. I was completely oblivious on how simple these trip clutch/cams really are. Thanks again for the amount of info in this video, and for taking away the "mystery" on how the trips really work on these plows.
I have a John Deere 55h moldboard plow do you have any bushings for the rear wheel there's lots of play back and forth about an inch maybe a half inch but I think it's more like a inch and a
Do you have any suggestions
I got it figured out. "Till guard" Thanks for the info
I cannot pick up what you said the product you are using to spray moldboards. would you spell it out please
or the cheapest spray enamel spray paint you can find, the cheaper the better
when you're done plowing, PAINT the moldboards with primer then cheap rattle can metal paint. keeps them from rusting away. mine sit outside all year and next time i use them, after the paint wears off, they look brand new.
How does a guy identify the plow model number on a set of these old plows? I have a set of 3-14 JD plows very similar to yours, would like to get a positive ID on them?
Thanks for your clips on these old plows. With your info I was able to disassemble and reassemble a #44 and turns out (yes-pun intended) it works. I'll be looking for more info on how to get axle shims and the clutch kit and other miscellaneous unicorns. Field day is today so wish us luck.
Damn sucks he’s going to have cancer and Wiese isn’t going to pay his medical bills.
I need some help. But I can’t figure out how to contact you
Great class!
where can i get shims? I've tried looking on the internet and cannot find anything.
Spectacular !! "John Deere" 720 👍👏💪💚💛🇺🇸
Remember back then when you could whoop your children to do the job for free
So I picked up an old JD 4 bottom 3 point plow with no coulters. how will this turn sod over without coulters ? I was considering buying some 1 1/2 in rod and mounting them in the old clamps and sharpening the edge just to score the sod first , crazy ?
It may work but will likely not be nearly as good as a rolling coulter.
@@tylertheplowguy8690 Agreed but the cost of 4 used coulters is more than I paid for the plow. without them will the plow blades rip the sod and leave a jagged mess ?
Without coulters, your plow will likely clog up often and terribly. The 1 1/2 in rod idea in the old clamps will most likely break all of the old clamps and will clog up. Try finding used coulters at junk yards in your area or put an ad in the wanted adds. Until you find coulters, disk the area you want to plow first or rotary mow and disk to chop up plant vines. I plowed 10 acres the other year. Started with notched coulters on the plow. The notched coulters kept getting wrapped up with vines. I could only go about 100 yards and the plow was clogged up terribly. Subsequently, I rotary mowed the entire field and changed the coulter blades to the plane round type and adjusted the coulters per the book. Went back to the field and no more problems with clogging. The plane round type coulters cut the vines like a hot knife through butter. Plowed 10 acres with the JD 620 in 3rd gear and F145 3-16's. @@ExploringCabinsandMines
Will sandblasting moldboards work ?
Very useful and informative video, thank you.
Good video.
Good to know! We’ve always used grease as you mentioned
Hey there Tyler I was watching the 1952 B cutting hay and I have a question does you're B have a RPM gage and if it does how would put one on a 1952 B without one installed any help would be appreciated 👍😉
How about vegetable oil? Not quite as messy as grease but not as easy as the method shown in the video.
Where do you get parts for those?
Where do I get parts for the vintage 415a john deere plow 2-16?
I think the cast case on my 44 clutch was damaged by ice. The gasket mating surface has gaps and appears that it has been bent. Is this common? Can a replacement case.be found?
Like your videos, I found a 416-14" that had been in the fence row for over 30 years last summer, plow is in excellent shape for S.Ga and never been inside. New set of shares from JD parts and put it to work. The trips not even rusted up and the moldboards still have the little metal tags on them.
Thanks ☺️
Hey man! thank you so much for the Video. Helped us a ton. The bushings for this have been rendered obsolete and I am looking for some. Where did you get yours?
Thanks for this video! Saved me a lot of time tonight!
Pull that thing through the ground a few minutes and it'll shine like new
Yes, that is all I do. A couple passes and it is shiny.
Hey, can you contact me I need some assistance identifying a POSSIBLE John Deere 2 bottom trip plow
Thank you for this video, very short, but very helpful to someone who knows nothing but am getting into using a plow. Thank you!
i need one of those kits for john deer trip plow closed clutch,how can i get one
mrbtractors.com and fill out a contact form.
@@tylertheplowguy8690 yessir i did today
Why wouldn't you just buy the pioneer 9500 lever couplers and bolt them on, and get rid of the John Deere crap
What is the number for the hydraulic hose tip for the 9500?
@@America-First2024 not sure without looking, but it's just the standard pioneer end
You should come plow at rollag Minnesota Tyler. It's the most awful stuff on God's green earth to plow
Uggg cbhjv fu cuhchucvhhvghvccchh
you must have done something wrong. I've had the jd iso kit for years on 2 tractors,no leaks! how did you keep insert from turning when 1 1/4 coupler was tightened? cost?
He said there's a groove at the bottom of the housing, to keep barrel from turning.
Such a great amount of information thanks
Many thanks for your time and effort. I was stuck and had no idea that CZcams could help me but it (YOU) did.
Looking good! Have you ever considered covering JD disk plows? Not a lot of good content on CZcams about them
after a period of time now. how do you like the Waspi /Grove conversion on your tractor?
I always wondered how they were made.
Do you have parts for a John Deere 614 single bottom plow
My parts guy told me there is probably more oil leaked in the fields by farm equipment than any amount of cars on the highway.
I'd put money on it. Lol
I have a 1030 John Deer Lost all hydraulics working fine and all of sudden quit. what do you think. changed the filter still nothing.
You have pump failure
Priceless experience for that youngster! My uncle Eddie let me stand in front of him when I was 6 in the mid '50's, on his JD 1951 model A. I have an A today that I ride in my late 60's now. My uncle rides in my heart. Very emotional stuff. Bless the souls on D-Day beaches this weekend.
Looking for a plow share for my NO. 44
Use plastic mouldboards instead
How do we get ahold of you for shims?