Video

@@AwwSSnap I think Safelite actually sells replacements but I don't think they have the windshield trim anymore

@@RspecNick those are priced up over $1000 I’m looking for cheap used ones

@@AwwSSnap that's probably on par with a used one. Most svx guys hold onto there parts cars like it's gold

@@Smodlee I had 3 alittle after this video was made. I was bored so I wanted to see what all it would actually take and the budget it would cost.

@@AcidxAnarchy sounds like air was still trapped in the cooling system causing it to blow excess pressure into the overflow tank. That's based off knowing you just swapped a hose. If it happened before the hose replacement I would say possibly thermostat but with the hose just being replaced high chance air was still trapped in the system causing excess pressure.

@RspecNick do you think air in the system would cause the heat not to work, tho? Maybe it blew all of the coolant out before it could get hot enough to get to the heater core? I would hate to change thermostat if it's just air in the system ya know?

@@AcidxAnarchy yes air in the system can cause all sorts of issues. Especially if that's happening right after you changed the hose it's more then likely air trapped in the lines. You did bleed it after the hose install right?

@RspecNick no I did not, I wasn't aware I needed to when I did it. I haven't run it since then, and I've been researching more into the matter.

@@sehismith thank you there's more to go yet

@@vipersquad3 Easy money saved

@@faithwashington1530 I do not know it unfortunately I tried looking for it when I did the filter and I never could find that bag I'm guessing it might be a dealer only item which is order item. They may have even completely redesigned it to remove that cause most cars don't have that bag.

@@jestemadrian4106 the evo prosport gauges?

@@jestemadrian4106 prosport evolution gauges 52mm.

79mph with GPS if I tweaked gearing alittle it would be over 80

I have the kehin carb and the nibbi intake tube. I don't mind them tho the carb is definitely snappy

Glad it could help

Holding up great honestly

The tao tao bws series? It's just a Yamaha Zuma clone from the Chinese market.

@RspecNick yes over here a local scooter company rebrands them as rougestars

@@dareallevi515 they are a decent looking scooter for sure

Glad it could help

Crap quality control and garbage bearings

I had a 2WD but I have heard there are lift kits available for them

I was on a 118 main and 38 pilot. So I'd start at like 108 and 36

@@RspecNick aw man i dont have a 118 unfortunately

@@fuwaldaVL a jet kit is fairly cheap on eBay I'd just grab a pack its probably like 10 bucks for a set of like 14 jets 7 mains and 7 pilots

@@fuwaldaVL what kind of carb do you have?

@@RspecNick just ordered the same one as in the video but 26mm. I looked on reddit and they said it should be running good on 115-120 and 34-38 just gotta play around with it. Also how did you do the airbox delete because theres a hose coming out of the airbox and idk what to do with it.

I originally wanted to get a 2.0 Rspec. That's how I went with the name Rspec Nick.

There's quite a few guy around that size riding them. The ones with the dual shocks tho if you remove the second shock it may crack the transmission case tho. It's cheap aluminum

No they have reverse,running and brake lights.

I'll be here

I'd do the basics first I'd check the variator for a washer which restricts speed usually in the middle of the variator. You can also swap the variator weights and belt to get a slightly better top speed

Thanks for the input, which weight 11 maybe?? I live in Florida

@@johnnygoni7402 most guys your size run 10 gram weights but 11 might be a decent happy medium. I ran heavy weights but I'm also lighter by 100ilbs

Mine was a 95 auto v6. Rockauto has alot for the truck.

I heard they are actually pretty fun but I've never had one. I wouldn't mind one tho.

Basic oil and filter changes @3000 mile intervals using mobil 1 5w30 and I went with a new clutch when the slave cylinder died @ 67,000 miles. Once this motor is done I'll probably only run liqui moly 5w40 molygen

@@RspecNick did u ave to do any carbon blast because of these GDI engines

@@theonefamily3786 you can do a spray and soak treatment but it's definitely not as effective as a full on spray. They recommend a valve cleaning treatment every like 30k miles

Long case 150cc it came on the scoot

Glad it could help

Maybe I can get with them and see if they will do a group buy or something. Cause the kits were deff cheap. Cheaper then the turbokits.com ones.

Just messaged Alec yep they stopped they sold 15 kits in the last 2 years

@RspecNick not sure if my last message went through, but he had an insta live last month trying to revive the kit. He was trying to get 20 ppl to group buy by May 17th with a $1500 deposit, but I'm not sure if the goal was met

@@Nick_XP I don't think it was honestly which sucks I heard the fitment was really good

It's supposed to be the only one that does work apparently 10-15 degrees cooler temps unlike the orange ones

Hey what's up and yes I'm working alot but the fan does actually work roughly 10-15 degrees cooler vs the OEM setup. It's one of the very few fans that actually work the others don't actually work like the orange ones. The build I ended up completing in later videos and I actually just sold it for 2k to a guy in thurmont Maryland. But hope your doing well as well 👌

@@RspecNick Thanks for sharing the info. All my scoots are EFI liquid cooled. 2.k nice dude 👌, probably could've got more. I do quick scoot flips when there's meat left on the bone. Few & far between nowadays 😔 & parts have been scare from China lol. Liked the builds you do 👍✌️

@@just4kicks950 that would be nice to go with a efi setup honestly and yes I could have definitely gotten more of I held out but the person seemed interested enough so that was a solid sell. I'll probably grab another one down the road since they are so easy to find

@@RspecNick I have a Piaggio Typhoon liquid cooled EFI & a Yamaha Tmax 300cc . I got a zip 50cc sitting no title with broken plastic's . If you're interested for $100. To be honest I can't find parts on my end definitely, needs crankcase seals or reeds. I was going to apply for a title. Without plastics why lol . I can donate to you & your channel "free" but no delivery (Ohio)

Yes main cats are still there

I don't but it should be in the video I think

They are definitely fun. I was gonna grab a 24 gen 5 but I'm waiting till I get a house so I can store it in a garage

@@RspecNick frsss bro definitely go for it i got mine in layaway payments and keep it at work

@@kalex9027 How much total was it for you I haven't really priced them out yet

Glad the video could help