Video

Thank you very much very helpful Bunnings trough no instructions

We're does that black u disconnected under the stater motor go does it run up to the 30 amp breaker

What's the copper anti seized for?

Add alum to speed it up or dextrine... to slow add some let or plasterer Lyme (hydrated Lyme but you should leave it to soak before you stir and apply to the wall it's basically old fashioned Lyme putty mostly used in wall art carving in situe or for casting ceiling roses, arcitraving, coving, dedos or picture rails in situe using a roller jig to apply to wall and carve whilst it's wet....milk is not good it creates mold spores in the wall coating same with urine which is disgusting practice no one ever did that unless they were a cowboy and vindictive little cnut never heard of lemon juice or citric acid being used but I guess it might work however it would no doubt cause mild spores to grow in time within the walls which is hazourdous to a person's health... I was in plastering for a long time and know quite a bit bout it traditionally we used sand and lyme to make backing plaster try it and see how much longer you can work with it as aposed to sand and cement you can work with it longer as it remains playable whilst it is being moved around if it stiffens a bit add some water to knock it back but be warned you must be careful as Lyme is highly corrosive wear gloves or coat your hands in baseline to prevent it being in prolonged contact with your skin other wise you might find it melting off your skin before you know it I know had a little accident screwing a floor with Lyme in the mix I didn't know till I'd finished went for a shower and found I'd melted all the skin off my knees from knealing on it whilst leaving the floor screed in a large 20' x 25' basement room it was bad the raw flesh was still reading high alkaline for 5 hours after hospital surgically scrubbed them and ran ice water on them constantly ... basically strong alkaline is same as strong acid it will burn through literally cooking tissue and flesh until it is neutralized and oh balance is normalised ...I hadn't noticed it had soaked through my cargo trousers and knee pads didn't feel any pain till I had took off my trousers and raw flesh was exposed to the air hence why I say be careful cause you may not notice any pain or damage till it's too late and the damage is already done

Thumbs up if you believe this video should be studied in film schools!

THANK YOU!! And no, you're not the only one who likes manual windows better! I DO!! I have an 87 Silverado and have had nothing but trouble with my power window motors! I just bought manual regulators and will be installing them this week. Thank you for making this video and explaining everything so thoroughly.

Afternoon - please could I hack a few seconds of your video - about 2:00 to 2:10? I just need to show the cover plate being removed, and the little 'cup' underneath. (On the Sportster, this changed in 1979 and in 1980.) It'd be helpful in my next video. Cheers, Chris

I so wanna hop on that seat after you get her fired up and sit on it while it warms up!🤙

Interesting video on the Rodeo, thanks for sharing it with us.

Nice mate big work. Well done as always.

9yrs later and this is still a valuable vid. Thank you.

This was very helpful. Thank you! I've an '89 2.6 Rodeo, and have never replaced coolant on a car before, so this video is a great resource. From what I can see, you fill up with coolant close to the top of the radiator, and then simply make a visual judgement about when there's enough in there?

thankyo for the no bullshit video....good camera...good volume and right to the point....very very valuable reference video/info for the harley evo owner/rider who works on his/her bike as compared to go to a high cost dealership....thankyou again....more is welcomed !!!

Very good sir

The bolts on harleys are metric btw

Love you’re work, I’ve got the same car these videos have been a great reference source ❤️

Hello, from California! Thank you so much for your Camry transmission fluid change video. It really helped me! Your directions were so meticulous and considerate. I like this video too. You're a cool person! I'm glad you're doing well! Very much looking forward to your 2024 in review! Cheers :)

Good luck getting the cam cover back on if you pull it with all the push rods and rocker arms in place, if you get it to pop back on you got luckey!! Just cut wired and pull thru hole in cover and lube up new cable cover and wires and pull thru, put connector back on new wires, assemble and done. Dont forget to set timing with timing light! Sorry but thos guy went thru a bunch of extra steps and work for no reason!

New one looks bigger to me

i wonder , wasnt it supposed to leak a certain amount of oil out when you take off the cams cover ? or you already drained them ?

Hey mate, I have got Holden Rodeo 1996, auto. Gear oil change video would be really appreciated. Waiting for your reply, cheers mate!

I do not have a kit. The installer of the cabinets will not help me put drawers back in!

I need to know how to put the drawer itself back in. I don’t need to know how to take them apart

Auto electrical work. It's a nightmare isn't it mate

are they still working now?

This Spray cordless paint is good or worst?

Awesome vid!! How do b doubles work in regards to red light cameras? Is it only the truck that has to go past the stop line before the light turns red?

good video, even it's 11 years ago.

Maybe do the video demonstrating how to do it🤔😂

They made the dome light in the 2000 camry sedan almost unrepairable. Different design than the one you have here but i was able to take it apart and clean off the copper connections and it works great now. That was after almost losing the marbles and springs about 10 times but thanks for the tips provided in your video.

I wonder why there are only a couple of videos on the entire CZcams world that attempted to prolong the utility of boots/shoes with Silicone... (That is a 100% Silicone product, right?) So that fix lasted +- 3 more months... Did the soles split apart again? And did you try to reapply the sealant once more or would that require removing the previously applied material? I've noticed Silicone is pretty tough to pull out after it's dry...

Merry Xmas mate. Good to see ya

Was it sucking air from a loose connection?

Only thing I'd do differently is, tuck the strap under the bit that goes around the barrel. That way it's less likely to twist when turning corners.

The crazy thing is, its nearly 2024, I film using a Canon EOS R which is capable of 4K and I'm looking to buy an old compact camera just to see how awful the footage is.

Very good demo 5star 10 pionts mate

Looks good, but the blinker indicator should be on the outside, and reversing should be facing inward. There, otherwise, it looks good.

A very in-depth video, much appreciated from someone in Victoria 😅

It worked for me, thanks for the Vid.

Thanks so much for uploading it! Really healped this idea.

Damn... I believe I'll stick with my SRW F350, thank you.

Holy dooly mate. How old are the battery's? I've seen similar in over charging land cruisers before..

Never needed it, natural immunity has proven far superior. I still have not had the virus to this day. Check Dr Campbell channel.

Is it still going?

Is this truck 259? I Hate it haha😂

Awesome mate. The Bosch looks nice. Top of the line to

I always wanted to get oil cooler for my 67FLH, but I'm not sure the oil return pressure is high enough to pump around those hoses

Bhout old 🗝️

Wow, I sold new and used toyotas in 2001-2003 and never seen or knew their was a wagon for this year!