Video

where did you connect the light blue wire?

Shifter interlock solenoid is the other half on the system, when it goes bad it doesn’t let you shift into gear because it binds up. That’s the issue I’m having with my truck, I’m going to replace both parts

I appreciate taking the time to make this video! I figured that back value was gong to be a pain seeing it being snugged up against everything else guess I'm about to share the same grief.

Look how your strap is touching the fender no real professional would do that !!

IF you are the fastest moving car on snowy roads (especially during a snowstorm) it's almost certainly not because your smartest or best driver on the road, usually it's opposite.

Don't be so sensitive

When you say cheap, how much do you think you spent?

You screaming "Ok Garmin!" followed by you fighting Garmin's voice recognition is amazing!

I always wondered what truck drivers do all day long, seems they drive around griping at all the other people on the road. But I agree there are a lot of crazy drivers out there and would guess that NJ has more than their share.

3.23 And this guy has a driving license. Take it away before it is too late.

you can cut the oil drain bolt on the side of the engine that hits the front frame section and slide the whole thing away from your rear fender/frame about a half inch, just enough wiggle room. theres a 2nd oil drain bolt on the other side so you can still change the oil 😎

I'm in the process of doing the same thing just trying to make a retractable mast so I'm not riding around with all that in the air... good build❤️👍

How did you just get the rear off? I have a bolt that broke when I did the wear ring install and now I have to get to the inside of it to replace the pump support

I been wicked paranoid about this problem but at 275k miles mine still don't leak. No idea if I've just been lucky or what. I don't think the case had the fix done beforehand because when I changed the fluid there was a ton of super fine metallic you could see in the oil. But the level stays full and the case still works. I'm swapping in a manual transmission with my rebuilt motor and wondering if I should reuse this case or just get something else

So you don’t have to take intake off?

This is the best one I’ve seen yet.

Yeah it’s not completely burning all the diesel but still looks cool I had a N14 black top rated at 350 and I think max was 430 but took it to cummins and mech was able to bump it up to 500 I was concerned about the driveshaft but he told me it was fine because it was rated for 1850. One of the best engines I ever owned it’s a toss up between N14 and 60 series both good engines and parts are reasonable unlike cat parts you have a black you won’t spend all your money Jack you have a green your pockets won’t be lean you have a yellow you’ll be one broke a$$ fellow

Probably a foreigner

& yeah but definitely not wayy back in the dayy of trucking & true & experienced & real driver's

Everyone makes mistakes just like your parents naming you Dominick 😂😂😂😂

That driver has NO understanding of the dynamics of navigating that truck and trailer on the road!

Oh thank s for telling me about the sign, he can read English !!!

The level of stupidity is beyond my comprehension!!!!!

Its not just Western Express. This problem is truck industry wide!

I had just seen u built ur Dump Trailer video. works and look COOL.. Congrats Young Man..

Great idea and video. What year is your Studebaker truck?

Cat is now offering a limited number of new casting C15 blocks. 😎 Unfortunately, you MUST have a core. It doesn't necessarily have to be a C15, but there are a lot of stipulations. But if anyone is looking for a C15, this will probably be the only opportunity to build an entirely brand new one, instead of just a rebuilt.

Thank you, there isn't any videos of this.

Hello Brother, please let me know the stock handlebar type which you changed. Where i can buy that. Thanks.

Thanks for the video. Nice shop setup. Vermont sure is rough on trucks. I’m in Mass and my truck is pretty crusty as well. After needle scaling my frame for a similar repair I think I lost 100 pounds in rust. 😂

I liked the idea of using a fuel pump out of an old car, rather than having to buy one on ebay for these projects. Thanks!

The paper I received said to block off the waste gate. Also it is only a c12.

Hello FcDominick,,,can I use this clip in my compilation? Any comment what happened? Thanks

Hello! We're creating a new compilation and we would love to include your video on our social networks. Can we use it? We'll make sure to credit you properly

In the first instance I could have put that stop down to stupidity, but the second incident I would wager they are scamming

Get a life

it's "tries".

And thats one of them 😅

Hello FcDominick, can I feature this video "Insurance Scammer Try’s Causing a Wreck (Caught on Camera)" on my CZcams channel? I will credit you on-screen and provide a link back. Do you have any updates or comments? Where did this happen? Stay safe

The trailer looks awesome, can I ask you why you used a winch and not a hydraulic cylinder? Wouldn’t cost more…

Hi, do you think merging two or more compressors will increase definitely the air flow? Thanks.

ANOTHER dyno run with NO numbers ! minute 39 wasted

you can padding afeine from this wood

ya i have a 99 shadow ace and in the process of changing mine too just have to take both sets of bars to a freinds house to use his drill press my drill is junk looks good

I would definitely hire an electrician to rewire...all of it.. if you are gonna be repainting everything, would suggest getting it all replaced before hand.

I prefer a short mast with scissor hinge underneath, winch cable rides on pulley and picks body up to around 30 degrees then the winch starts pulling on the scissor hinge rest of the way. What winch did you use?

Can you post a link to your windshield?

Your language is atrocious.

The items in the ceiling look to be servant bells.

Secret room? It’s called an attic 🤦🏻‍♂️