![Valkyrie Workshop](/img/default-banner.jpg)
- 22
- 34 315
Valkyrie Workshop
Norway
Registrace 20. 07. 2016
RC Models, Crafting, 3D printing, 3D Modelling, Electronics, Scale Models, Design, Tinkering, Aviation, Flight Sim
In case you want to support my work with a little tip, there is the link below đâ€
In case you want to support my work with a little tip, there is the link below đâ€
đą How to Make Simple RC FPV Plane - FUSELAGE - Double Maiden w/ SpeedyBee
đŽPrevious episode: czcams.com/video/6mJfktU9TQA/video.html
This is the third video in the series of building an easy - simple FPV RC Plane using Hot Wire Cutting technique to make precise, light and cheap airfoil - wing from foam, quickly even with no experience.
Simple fuselage from cheap and light DEPRON.
The most important thing to learn from the video - donÂŽt cheap out on servos! ItÂŽs not worth it, especially on projects that takes some time to build.
PDF Plans + STL: drive.google.com/drive/folders/15x4wyNKYbcZT7L2nRuPErl8FIH6wn1ER
SpeedyBee F405 Wing Mini case: www.thingiverse.com/thing:6698781
-----------------------
0:00 Intro
0:12 Fuselage Build
5:14 Maiden Crash
6:20 Rebuild
6:43 Maiden 2.0
8:25 Landing
9:30 Outro
-----------------------
#rcplane #rc #uav #diy #rchobby #wing #fpv
This is the third video in the series of building an easy - simple FPV RC Plane using Hot Wire Cutting technique to make precise, light and cheap airfoil - wing from foam, quickly even with no experience.
Simple fuselage from cheap and light DEPRON.
The most important thing to learn from the video - donÂŽt cheap out on servos! ItÂŽs not worth it, especially on projects that takes some time to build.
PDF Plans + STL: drive.google.com/drive/folders/15x4wyNKYbcZT7L2nRuPErl8FIH6wn1ER
SpeedyBee F405 Wing Mini case: www.thingiverse.com/thing:6698781
-----------------------
0:00 Intro
0:12 Fuselage Build
5:14 Maiden Crash
6:20 Rebuild
6:43 Maiden 2.0
8:25 Landing
9:30 Outro
-----------------------
#rcplane #rc #uav #diy #rchobby #wing #fpv
zhlĂ©dnutĂ: 7 056
Video
đą How to Make Simple RC FPV Plane - Hot Wire Cutting - Perfect Airfoils With No Experience
zhlĂ©dnutĂ 6KPĆed mÄsĂcem
đŽPrevious episode: czcams.com/video/cZ_55MPOF4Q/video.html This is second video in the series of building an easy - simple FPV RC Plane using Hot Wire Cutting technique to make precise, light, cheap airfoil - wing from foam quickly even with no experience. My apologies for any bad AUDIO quality I am still tuning it up & learning. PDF Plans: drive.google.com/drive/folders/15x4wyNKYbcZT7L2nRuPErl...
đą How to make simple RC FPV PLANE - with NACA Airfoils
zhlĂ©dnutĂ 5KPĆed mÄsĂcem
đŽSecond Part: czcams.com/video/6mJfktU9TQA/video.html Long Range UAV or just a RC ( FPV )TRAINER? Designing a RC plane with very easy calculations or via online tools. Making airfoils templates for hot wire cutting can be a little time consuming, but once set up, wing can be made in just few minutes. Again the plane is supposed to be mainly modular so EZ parts replacement or even trying differe...
đĄ Simple RC Plane - Trainer For Beginners and a lot of Fun | INDESTRUCTIBLE | EZ DIY
zhlĂ©dnutĂ 1,5KPĆed 2 mÄsĂci
I have a lot of fun with this EZ Trainer. Perfect for training or just relax flying. Low Fly-Bys are always very enjoyable. It can fly quite fast on full throttle but I also like to fly on the lower limit - as little throttle as possible and close to the terrain. How to make Simple RC Plane - Trainer for beginners. DIY Cheap Easy Indestructible - Unbreakable - Modular Airplane: Wingspan: 1000mm...
đ”INAV AUTO-LAUNCH | đ„ ESC OVERHEAT đ„ | MISSION
zhlĂ©dnutĂ 828PĆed 2 mÄsĂci
UAV landed by itself after disarming. No damage, not a single scratch. ItÂŽs nice to have a Flight Controller that keeps the plane stabilized in such a situation. And the Auto Launch.... I love it! INAV AUTO LAUNCH DIY UAV DRONE ESC OVERHEAT RC UAV: Wingspan: 1200mm Wing area: 27dmÂČ AUW: 1700g HW: TX: Taranis Q7XS RadioMaster Ranger Micro ELRS RX: MatekSys ELRS-R24-D or ELRS-R24-S VTX: Eachine T...
đâĄDIY BATTERY PACK | MASTER SOLDERING | LI-IONâĄđ
zhlĂ©dnutĂ 734PĆed 3 mÄsĂci
Learn How to solder battery - to make your own battery pack out of lithium-ion (Li-Ion) cells. For occasional DIY Packs, no real need to get a spot welder. Even an investment into more powerful soldering iron will be more practical. The tutorial counts with at least some general knowledge and safe manipulation with any battery. Remember: SAFETY FIRST!!! When soldering my battery pack, I was rea...
đĄđš DIY | RC MOTOR PROP THRUST TESTER | STAND | RIG
zhlĂ©dnutĂ 2,6KPĆed 3 mÄsĂci
âIMPORTANTâ: I DO NOT recommend 3D printing motor mounts for high thrust setups. Make rather something really rigid! Learn How to test thrust of a propeller for RC motor. The design is simple and easy to make. ItÂŽs all up to you what materials, dimensions and parts you want to use. Just remember: SAFETY FIRST!!! Motor in this video: 5010 750KV with APC12x6E prop. Music: âș Music Credit: STEESH T...
RC Plane Crashes: When Torque Takes the Wheel
zhlĂ©dnutĂ 356PĆed 4 mÄsĂci
The motor is "too big" for the UAV, as throttle goes up, it rolls left badly (CW PROP). After several crashes, slow-mo inspections, I gave it some up and left angle on the motor mount. It indeed helped, The CG was right, balanced on both axis, I am just bad in reacting quickly on the sticks, focusing on good toss and not getting prop strike đ Practice makes perfect, I guess. RC UAV: Wingspan: 1...
RC UAV | Hand Launch Practice | Safe 12" PROP clearance | 4K SlowMo
zhlĂ©dnutĂ 372PĆed 4 mÄsĂci
Unpowered hand Launch practice. My goal is to do powered launches safely, thus some unpowered launches and video frame by frame revision is required. It is fast spinning knife at the end. UAV Prototype Mk.2: Wingspan: 1600mm AUW: 1800g #rc #uav #pusher #handlaunch #rcplane #fixedwing
Shaking EMAX ES08MA II Servo - Original Or Fake?
zhlĂ©dnutĂ 298PĆed 5 mÄsĂci
Shaking EMAX ES08MA II Servo - Original Or Fake?
SPAD.next | Proper REVERSE Thrust settings | MSFS | PMDG 737
zhlĂ©dnutĂ 529PĆed 6 mÄsĂci
SPAD.next | Proper REVERSE Thrust settings | MSFS | PMDG 737
MobiFlight | Proper REVERSE Thrust settings | MSFS | PMDG 737
zhlĂ©dnutĂ 626PĆed 6 mÄsĂci
MobiFlight | Proper REVERSE Thrust settings | MSFS | PMDG 737
MSFS | Any TurboProp Throttle REVERSE via SPAD.next
zhlĂ©dnutĂ 52PĆed 6 mÄsĂci
MSFS | Any TurboProp Throttle REVERSE via SPAD.next
MSFS | PMDG 737 Throttle REVERSE via SPAD.next
zhlĂ©dnutĂ 206PĆed 6 mÄsĂci
MSFS | PMDG 737 Throttle REVERSE via SPAD.next
X52 Pro | MSFS 2020 | MDF Plugin - working đ
zhlĂ©dnutĂ 526PĆed 7 mÄsĂci
X52 Pro | MSFS 2020 | MDF Plugin - working đ
Thatâs funny I built a nearly identical test rig to measure static thrust. Doesnât tell you much regarding propellers for fixed wing aircraft but itâs great to test motor efficiency and ESCâs! Iâve switched to using CASTLE CREATIONS and T-Motor and Sunnysky, with APC thin electric.
@FPVREVIEWS Yeah I literally use it only to check if I meet approximate thrust and pitch speed, tho it's just static. But I never tested motor efficiency on that, may I know what's your workflow for that? (So far I sticked with Skywalker ESC and switching to SunnySky. (However dunno if the extra money on ESC makes some significant difference?)
Good job on the build :)
@@pjak2000 Thank you very much đ
What type of motor, specifications please?
@@sanjeetgill448 5010 750KV from AliExpress đ
Nice work!! I like how you build everything neatly! Btw I had the same servos that you used for the V-tail, the gears snapped... thankfully not on a flight for me đ đ I'm also making an autonomous FPV RC Plane right now. Will post a video about it!!
@@Avio_x Thank you very much đ oh damn! So you got similar experience đ My next build will get some serious servos! Oh cool, love UAVs đ„°
keep uploading, we love your educational video !
Thank you đ
I am sorry to bother you again but what was the material that made the body of the airplane from?
@@stephengould9385 No problem đ It is Depron. Or if you can get Foam Board that will be probably better.
what was the glue did you use on the paper -- What type of paper -- thank-you -- Steve
Hi Steve. It's any wood glue (PVA) and the paper, it's packing paper. There are more variations with different thickness so I go around local stores and try to find the thinnest one. Mine has one side matt and the other is a little shiny. But both are smooth, so it's not like rough paper. Rly the best way is to check multiple stores and get the best you can find đđ
@@valkyrie_workshop thank you for your time
@@stephengould9385 no problem đ
I would recommend not using black tape because of the weight that it adds. They have a shrink wrap that is super light that they use for Bolsa wood airplanes. I would look into something like that.
I totally could have used that. But I absolutely gave up on that idea when I saw what insane money they wanted for 2m of plastic (Oracover) đ€Ż It would definitely looked better, tho I'd not claimed how much I saved on weight, literally the 3D printed case for SpeedyBee is heavier than any covering đ Anyway, the tape is also light and thin so covering the fuse with few overlaps gives an extra layer and strength for landings đđ
The content you are making is excellent Valkyrie hold your courage and keep making it. I ask the Allfather sees your spread of knowledge and rewards you.
Thank you very much, I appreciate it! đ Allfather who, what? đ
@@valkyrie_workshop đ The Allfather, Odin, sends the Valkyries to select the souls of the slain warriors deemed worthy to enter Valhalla.
@@mrtea3122 Aaaaaaaa now I got it đ YouÂŽre right! đâ€
Great one.Just one tip.Use Acro during auto tune â€
@@cracker08121987 Thank you đ Yeah I know, the plane was indeed tuned in Acro. It's just on maiden I had it enabled all the time đ
I loved you video, your honesty is refreshing. Not everything goes perfectly first time. Well done!
@@user-dy5sb2fh7y Thank you very much đ Yeah, we all learn from mistakes. So If I can share an example to prevent someone else from making that mistake then it's good đđ
Whole build video?
Non existent
nice job
Thank you đ
I loved your video, well done!
Thank you very much đ
wherer did you get the depron?
It's used as insulation under floor so check out some HW stores đ
Normaly I use foam from dollar tree but after watch your video I think Iâm going to try that unfortunately that foam in my area is 1 inch thickness, by The way where you from? Not much girls in this hobbie đđđđ
@@javieruriel Ah in that case I would rather use Foam Board as I used for older UAV I have built. Well it's Northern EU đ mm I seen precisely one girl on YT but she's into RC cars. But correct, not many. Many are just interested in absolute useless BS đ€Ł
What versiĂłn of inav are you using?
The newest 7.1.2 đ
like i am also into this hobby but i fly fully manual mode with a flysky receiver
@@freshbeginners5373 yeah the good thing about FC or Gyro is you can disable it anytime and have full manual mode.
hey can u please give the 3d stl files for the mount and the bracket and also the connection diagram
Those 3D files were more like improvising and building around what I had available. I can upload it on Thingiverse If you want. For the connection diagram, I don't have there anything special apart from regular RC plane connection.
V tails are so cool.
I love them đ
Awsome build ! I love the Hobby King Turnigy MG-14 metal gear micro servos. They have lots of toeque and will survive hard landings with the metal gears and are fairly inexpensive.
Thank you very much and thanks for the recommendation! They have quite some torque!đI thought about original EMAX ES08MA II
Informative video! Wondering if any custom PCBs/ 3DP/CNC'd parts may assisit for upcoming projects? Would love to sponsor! (PCBWay zoey)
Hello đ I think, most likely for RC plane projects, custom PDB, Lightning modules, CNC Laser/ Milling templates.
@@valkyrie_workshop Sounds great! Would love to have a further discussion, may I know your contact information?
@@zoeyzhang9866 Hello, please use the contact information (e-mail) available on my YT channel info tab. đ
@@valkyrie_workshop Email sent! Looking forward to your reply!
You had me laughing when you said, 'madien crash'
It's either Maiden Flight or Maiden Crash. Or both đ€Ł
This hobby wouldnt be the same without toxic fumes
Haha yeah
Awesome video!
Thank you very much đ
Well, try autonomous mission next :)
@@IndraKurniawan-vk2qb Well I will try :)
Congrats on a successful flight! Looks like it flys great!! What servos did you use switch to? Iâm trying to get a similar plane in the air and I worry the eBay noname 9g servos Iâm using could be the issue. Also, what rubber bands do you use? I was using some from dollar store but they are garbage.
Thank you very much đâ„ïž Well I would ideally recommend Genuine EMAX analog at least. However, I obviously try to keep the costs low so I have done many flights on copies of Tower Pro MG90s from AliExpress. Those are good copies tho! Nathan - AerostuffFPV uses them in all of his builds. Hopefully the link will work, but from this seller they are truly full metal gear (some other sellers have variants where the motor gear is plastic, but it's mostly mentioned in the reviews) I ordered like 20 of them and so far only two were faulty, gears skipping. a.aliexpress.com/_EQFwFJp But Bear đ» in mind I'd rather recommend EMAX from Banggood anyway, those are genuine! And the rubber bands, I take any from my local hobby stores. I can't give a good recommendation for that. On the packaging it's JP (JPerkins.com) đâ„ïž
It was a nice flight. Can you tell me weight and flight time of the plane?
@@user-qc1gr4fr3f Thank you very much đ The plane had AUW 1361g (version without flight controller and GPS) I have not measured with the FC tho. Flight time is so far unknown. On maiden it was 15 minutes, kinda fast, consumed 1300mAh. I will have to set up a mission to fly and see how long will it fly on 4500mAh battery.
Use parachute to protect the plane
đ Better tell Boeing đ€Ł
Can I fly this with a Flysky i6x ( Esc 40a/Motor/ 10ch flysky receiver?) Without Gps/Camera
Flying manually will be hard but yes, you can. Remember to fly at nice, calm weather, without wind.
@@bq15096 I would recommend to get the cheap 12$ Gyro A3 V2 from AliExpress. You can tune it mid air and at least for Maiden it would be a "fail safe". If you want I can send you a link đ Even though the polyhedral gives some stability, when I fly manual I rather put some different color on the bottom of the wings to not get lost with the orientation further away đ
Awesome looking design, that flies well! Even though the fuselage is box shape, the end result looks sporty. Great tips and details during build process. Nice clean build by embedding tail wires in boom and using 3d print to mount the flight controller. The tip of using carbon rod as a fulcrum to find balance is one I have not seen, so will borrow. :)
@@AerialWaviator Thank you very much đđ Yeah some sleek rounded fuselage, with less aggressive angles would fit it well too. Yeah no problem, I've never seen such a stuff either đ But it comes from my first attempt to build a pusher UAV - I had fuselage built first and had no idea where to put the wings so this method has been discovered đ Luckily with this design the wing can be moved in range of 10-15mm so even without moving the battery one could do some fine tuning after. Or moving the tail boom. Literally three ways to fine tune the CG đđĄ
Very helpful video â€â€â€... Specially the CG checking part it was so simple step.
I am happy it helped đâ„ïž Haha I would like to claim it's my invention but not entirely sure about it tho đ€Ł
seems like your plane flies effortlessly
Sort of đ definitely the first Maiden was totally effortless đ€Ł
Anyone with some tip for a cheap & good camera (phone) to make better quality Fly-By footage? Those in the video were taken by my assistant with iPhone XS, but the focus while zooming is quite bad đ
Try to using "AE/AF lock" (auto-exposure/auto-focus). Point camera at tree or something far away, zoom-in, let focus (a tap on object image), then press-n-hold on view screen. Should see yellow indicator popup saying AE/AF Lock enabled. To remove the AF lock just tap screen again. Can still use two fingers to manage zoom, but some care is needed, as single tap on screen will unlock AE/AF. Better option is downloading a 3rd party camera app that allows manual setting for focus (set to infinity for flying views). The Apple default camera app's autofocus is not your friend when taking long shots, or capturing images through glass. Any time focus is off, it starts scanning from close to far focus, so for far away objects this results in bad focus much of the time. Adding an external telephoto lens kit to the iPhone can also help for far away recording, as it can be hard to keep an RC plane in close.
@@AerialWaviator Lovely! Thank you very much! I am not using iPhones at all so I will pass the instructions to my assistant đ Do you think an older DSLR would perform better? Got Nikon D3200, It has "proper" lenses, although I was told that the video performance is not that great compared to modern phones đ€
Wow! ive been building, flying and posting a little while so i know how hard you worked on this. Great build and just wonderful story telling. Add some b roll like your ride to the flying feild and show your preflight and youve got yourself a professional movie!
@@dustinwilson492 Thank you very much đ Yeah maybe? I am trying to figure out if people even like my videos so I am trying to compress the things more to not waste anyone's time đ
You actually jinxed yourselfđ But a good outcome tho The slanted tips really give accent to the whole platform, clearly seen in the autolaunch fragment. I'm sure it has aerodynamic advantages too (minimizing vortex somewhat) It just looks gorgeous and cruises quite efficient too with the FPV/HD profile behind the propblast. Love it. Congrats Val!đ
LMAO right? đ€Łđ€Ł The Droopies has an effect, In general, if it's designed to the plane and desired flight characteristics. Droopies like STOL package for Cessnas, or A10 got them. They should improve Take Off and Landing as said, and help with ailerons control authority as the high pressure is "trapped" under the wing. I am not an expert to Droopies tho, I added them mainly for design. But feels like it's flying on a rails LoL. Thank you very much Nathan đâ„ïžđ€
Very nice! I like the design of this plane! I would love it if you did a video about setting up and using inav auto launch in inav 1.7+. I have everything else for my plane working well with inav, but I've fooled with settings related to auto launch and watched videos about it and I can't get it to turn on/activate despite assigning it to a switch and using the procedure I've seen in videos.
@@lienmeat Thank you very much đ Oh I see. No worries, I will make the complete INAV walkthrough. The Advanced Settings page looks complicated on the first look, but it's very simple and I will show you how simple it actually is! I think many INAV videos are more yapping than helping.
@@valkyrie_workshop That would be amazing! You do a good job of explaining things without extra "yapping".
@@lienmeat Cool! đ Thank you đđ€
Looks amazing nice job đ
Thank you very much âș
Nice job, well done! Keep designing, building, and posting. Looking forward to your next project.
@@stevenshook5676 Thank you very much đ Will try my best đ€
Design Inspired by AeroStuff FPV: czcams.com/video/JZYMmtty2m0/video.htmlsi=PNy0B77quePcJfrv
Does the lion drain so fast
Not sure how the question was meant, but it drains the battery in correlation with amps draw. 4.5A will drain 4500mAh battery in "one hour".
A build video with plans and stl files?
@@kkuenzel56 I can drop you the STL files if you want. But IMHO the design needs a revision đ It was more like, OK I got a stick and now somehow to improvise to make an airplane around it. I might do a revision in the future, better build and better video than this.
Looking forward to the revision. Great video đ