Video

You guys are hiLarious! 😂😂😂 I need some of that strawberry grease for my window. Can I use PB Blaster?

Intake manifold issue and the tik issue from failed rocker sound so similar.

Awesome video! Us DIY guys appreciate it very much. Any chance you have the part number still for those parts?

Thank you for your detailed video. Best one I saw to help me diagnose and replace my starter. Subscribed

Do u got to unhook battery cables to do this?

No new snap ring ?

good video friend, is it possible to change the inner booth without removing the entire axel? thank you.

Hey man I just installed a level kit on my 2004 single cab Silverado but my shocks will no line up with the hole because the pressure the spring has I watched ur video on how to install the kit any suggestions?

How long can I keep driving the vehicle with this issue (crankshaft sensor) would it messed up some parts of the vehicle if I don't fixed it right away?

I cracked up when they came back to video after orifice tube removed he looked like he needed a moment 😂 thanks for making this video!

How long would it take an amateur to do this?

Also, dont forget to unhook the battery first :D

You make it look easy. Good video. 👍

What year did those rims came from?

Was the intake gasket blown

@ChristmanGarage - dude! Echoing those that have come before me in sharing THANKS for this video! My 2009 Sedona had the identical issues. I went a different path and ordered a OEM gear knob off Amazon and swapped it out in <3 minutes. Viola! Problem fixed - saving me GOBS of money for diagnostic + repairs. Thank you!!!

You know I’ve never had an issue doing brakes in the 90s but after i got my 15 Silverado i was like wtf is this 💩😂 but after watching your video im ready to conquer that job

I've been suspecting this was where the problem existed on my Kia for some time. Guess this confirms it. Time to fix it. Thanks for the video.

This helped me alot thank you sir

Miracle! Same problem, same solution. Thanks!

Dang son ,you made it look easy

So the wiper module can be opened up and repaired. Wipers on my 1999 MGM only work in high speed so when I move to low speed or intermittent I am removing power and wipers park anywhere.I Need them to work in low and intermittent to park properly. Multifunction resistance within specs on all speeds. Washer works but does not activate the wipers. So module or wiper motor?

Yeah that really is unbelievable that you did that with a John Deere Gator a piece of s*** you could have doubled that distance with a Honda

Thank you for your help this video is very helpful..

Hey brother, the four pin socket for that preload ring is W1272 at your local Oreilly store. The torque on that ring is 205 ft. lbs. (Yes I’ve got by using the punch & hammer too. But preload is important for longevity of that Bearing!). Thanks for the sockets and Rotor spacing tip! Two treated 4”x6” blocks 11” long stood on edge, with two thin steel plates on top makes your press cradle spacing (taller) deeper also.

How do you clean it so clean with out scratching it ? What did you use

Hardly any audio

Cadillac converter. From Volkswagen to Cadillac. Lol!!!!

Don’t know if I lubricated it right? I sucked it off for 35ish seconds but the car didn’t really give any positive feedback

Saved the day! Same exact thing on my 2014 Kia Sedona.

How did you get the other bolt out? Swivel socket or what?.....

I have an 80 F100 that I'm wanting to lower.

I wish I would of watched your video before I paid a locksmith to make a key! lol! It would have been a lot cheaper! lesson learned.

Awesome video! I have a 94 F150 I’m in this Tx heat the AC works. After watching this video I want to do this. Whats a ballpark $ for parts and labor? thanks you

Good deal

Straight to the point! Thumbs up my man!

Boss has one that's leaking but he didnt hire me as a mechanic. He hired me to lay brick.

So if it’s only a little fluid in the motor mount will it continue to drip

Thanks for the video. I just did the job. Would like to add that its best to slightly screw the top 2 screws into the heater core before sliding it back in. Then slide the black tube into those open face holes and put a bottom screw in. Then tighten them. Also anyone doing the jib should order the core with gasket included.

One time I was working on this 74 Camaro had been in the front end wreck so we thought the vibration was from event crankshaft or dampener, but it turned out when the bottom of the header tubes were flattened out a little bit the vibration exe was coming from the exhaust pipes not flowing evenly and part of whom were half restricted. The new setters of headers fix the problem.

Wow. I have a 2004 Kia Sorento and it has the same leak on both sides. Mine is also leaking in the middle of the ceiling where the overhead console is underneath the compass. I have had several "mechanics" tell me that the sunroof drains were blocked (paid to have them "blown" out at least 4 times). The last one said that I should seal up the sunroof (even though I don't use it often, I don't want to do that). The kia dealership claims that they didn't see anything and said that I should carry it to a body shop (they charged me over two hundred dollars to lie to me). I'm so frustrated by this.

hell yeah

You been watching oboy vice grip garage

Had a battery terminal (positive side) come off and give the same issue still gonna change the sensor tho

Did u had to change the thermostat?

I jus took the fan clutch off and gets you more room , great video

Does anyone know the report that for the metal plate behind the flywheel/flex plate?

What is the torque spec for the torque converter ?

👍👍👍👍👍👍👍

outstanding!