Video

Did you have the truck jacked up off the ground when doing the bounce test or does it have to be on the ground?

The fiber glass makes the sound not dampens

Hello Sr., if you just replace brake fluid, refilling the master cylinder reservoir with new fluid constantly and avoiding that the air go into the system, making this process until you see new brake fluid comming out of bleeder valves of each brake, do you need any special procedure for ABS module like scanner or like one that you showed in your video?.

Where can I get the pens to replace the ones you removed

I couldn't figure out why both of my headlights would just stop working at the same time. The relay! This video was just what I needed. Thanks for filming and posting this. 👍

When I put a new pressure line in it was a different design. They put a rubber seal on the line I had to pop one of those line seals out to get the line in. It doesn't leak there either. But my rack is leaking bad out the ends now.lol

I guess it was the heating up that really helped the most before using the 80Yrs old tool. Just saying. But yah, well done, it wasn't that easy.

Just picked up a 98 k1500 last Sunday!!

Oooh shiny! Billy likey.

@30 seconds already rollin boogers 😂

Good to see you, my man! I'ma checkem aht.

I can't wait to see these installed! Great video!

It looks good. Its definitely not 50 state legal. Do you have emissions where you live? If so it probably won't pass unless you know someone.

I didn’t know what love really felt like until I stumbled across this channel after purchasing an 02 sierra.

Awsome can’t wait to see what it will sound like!

Use code “DAN” at dynovoxparts.com and save 15%

There is the Maninator. I just picked up a 2003 Silverado extended cab stepside Z71.

I'd have to just put that thing back on the car and sell it quick

Both sound great. Think I'll go with the M80 for my 8.1 Silverado. Thinking 454, shorty headers 3" into a Flowmaster Y300400 Y pipe 4" then a Cherr Bomb M80400 into a 8in tip😂

Put new axel on And not it only rotates half way around. Is that normal ?

I pulled mine this morning and immediately had two of the bolts snap off. Do yourself a favor and get the bolts to replace the old ones when you buy your new bushings. If you buy bushings off Amazon or whatever, they may not come with new sleeves, so you may have to order new sleeves if they are needed. Check to make sure you are getting what you need. The bolts are 12-1.75 metric and can be purchased most anywhere.

I have a 04 Chevy Trailblazer 4 wheel drive I have noticed a grinding sound coming from under the car on l left side and when it goes in to a left turn there is a ting ting noise what could this be I check the bearing shake from side to side and up and down but it is tight no movement I am stumped please help

Buy a new cv axle and hub bearing

Very helpful way of checking an ac compressor clutch, I don’t know where the clutch relay location in my car is, so this method is simple

You should have opened the bleeder when you replaced the pad and pushed the trash into the ABS. It is common knowledge that you must remove the dirty fluid from the master cylinder resouivour. Refill with clean fluid and bleed with a one man bleeder tool.

Its not a 55 Chevy😊

What a marroon, you don't pump up the pedal, you step on it and slowly push down. The catch can on the bleeder is correct, but again you don't pump it. You need to bleed them with a tech two. Scan tools only diagnoses the problem and clears the codes. Hence you are doing it all wrote and videoing it so everyone can laugh at you.

GLASS PACK ALL THE WAY. NO COMPARISON.

Once you have moved it you have to move it the other way back and forth to loosen it up. I know sounds crazy but it works. What you are doing is compiling the rust to act as a wedge making it tighter.

Is it 2 piped into 1 at the end?

Just buy a new one ? you have it off ..

I think the problem is that you were using a hammering gun instead of a torque gun.

I've heard the gas cap has charcoal in them You might have to replace the cap?

Torque specs for the bolts?

What if you can’t turn the ignition to on cause you lost you’re key??

Very helpful, thanks bro

Thanks for taking the time, man this was an excellent video!! I thought I had to use a friend with a press, but I’m definitely getting that kit from O’Reilly. For those reading the comments and wondering the current rental price for the kit is $369 which is returned to you when you bring the tool back. So it’s a free rental.

At 5:44 I'd be swinging the large 10lb'r into the nutted shaft. One serious outta the park swing.

Should I work out at gym

One of my favorites

Hey love Chevy Camaros

would this work on a 2006 ss monte carlo ?

Everyone put there mask right there 😂😂

You should turn the u-bolts to the side or straight up. Hanging down like this can easily get them to hang up on various things.

Best video yet.Good job

I would test it before putting everything back on. I'm sure you did but didn't mention it. I have a 1991 Z28 to do. Should be similar.

I hope your family is doing well bud.

Дорогой друг, ты меня выручил! Я всё поменял сам по твоему видео! До этого искал мастеров, но те кто может или заняты, или ценник огромный. В общем справился. Будь здоров!

While you're in there replace the oil pressure sending unit.... It's cheap enough, and it's way easier to get to with the power steering pump off....... And they eventually go bad, and are a pain to get to from under the vehicle......

Salute sounds much better. Like a high quality modern muffler. No different than a magnaflow/borla straight through. Surprising from a $35 muffler.