![oakpoint solutions](/img/default-banner.jpg)
- 60
- 1 907 161
oakpoint solutions
Registrace 14. 04. 2008
Video
chicken coop part 1
zhlédnutí 91Před 4 lety
To purchase plans visit: wilkerdos.com/product/chicken-coop-imperial-units/
Locking hub replacement F 250 super duty
zhlédnutí 2,8KPřed 4 lety
Fast and easy locking hub replacement. How to replace Hub and bearing: czcams.com/video/4adtThASxwE/video.html
bearing hub replacement Chevy truck 2000
zhlédnutí 104Před 5 lety
Step by step instruction on removing and re-installing bearing hub assembly
samsung dryer heat problem
zhlédnutí 876Před 5 lety
A quick help to trouble shoot your Samsung Dryer heating problem How to replace your heating element: czcams.com/video/Hw4ndHbIBnE/video.html
1993 F250 tie rod replacement
zhlédnutí 7KPřed 7 lety
My tie rod broke off on my 1993 F250 while out in the woods in the snow. Managed to drive it home, fixed it for about $20.00
Samsung Dryer Repair M# DV45H7000EW/A2
zhlédnutí 302KPřed 7 lety
Replacing Heating element Samsung dryer
Changing to LED Brake Lights Honda Goldwing
zhlédnutí 14KPřed 7 lety
Changing to LED Brake Lights Honda Goldwing
Kuboat tractor fuel pump problem and fix
zhlédnutí 118KPřed 7 lety
Kuboat tractor fuel pump problem and fix
Juat used the screw driver method. These new alarm ones are a pain the ass. Older ones took less than 30 seconds. 😂
I prefer some wire cutters less damage to bottle lol
The music was creepy and annoying
But very educational
Thank you so much, Man with the wisdom. 🤍🌈🥰
That's awesome
great video. any tips on re-assembly?? particularly getting the belt back around the drum?
Hero
Kitammuort, pe miracol nn m'agg struppiat
Strong magnetic works
I just turned it upside down and hit it with a hammer at an angle towards the ground and it came off. Broke the cap a little but it still screwed back on.
Use a fucking magnet
I used a hacksaw. I tried using the flat head but it started cutting into the glass. You might need two people with the hacksaw because the bottle will move on you too much.
Omg that baby is the cutest
I bought an air chisel yesterday on the strength of your video. I`ll try it out today I have the upper control arms off my `80 G10 Van ready on the bench.. cheers. watch for update.
Thank you
Can that be done while still on the car?
possibly, but then fitting the new bushes would be a challenge.
lol I was afraid the bottle would break, but eventually I was able to pry the top off
But... how long did it work ?? Ive put 4 different brands and styles on my kubota, full electric power at all times.... the pumps dont last a day ??!!
Thanks so much! Great tip. I don't have the strongest air chisel but it took the bushings out with ease in minutes.
Could you provide a link to where you got the part
Mine won’t has no power what can I do
Broke the bottle. Moronic advice.
Holy Smokes Dan..... Looking for a video to help me repair my dryer and you pop up! Small world. From intubation and ACLS to appliance repair. Thanks man!
I went to crank my B3350 and the red engine warning light came on after it started up and the throttle wouldn't do anything. My dealer who is pretty good at helping out suggested that because it didn't throw a code it was probably fuel related and not electrical or a catastrophic failure. I changed the filter (it was dirty but wasn't the fix) and then unhooked the fuel pump with tips from your video and made sure it flowed good fuel. It now works perfectly 👌. You saved me at least $1,000.00, thanks!
Thank You - 2 of 6 boxed bottles of Dewars scotch had locks on them (from Woodman's) THANK YOU!
Thanks for sharing. 👍
I find it funny that you ended the video without removing the old spring and putting the new back in. I'm guessing it wasn't as easy as you claimed.
It would have been nice if there wasn't music drowning you out and if you weren't figuring things out as you were making the video. The stuff I wanted to know you didn't show and just said that you did, like taking the door and front stuff off.
Mine are from a 1967 Buick Riviera. Mine are taking hours!!!!
You know it would have made it a whole lot easier to get to if you went in from the bottom
Can you come help sos
Yes still having troubles here
Its the only way to fly.....
Question
I will try this method tomorrow!
I don't recommend this video at all. Eventually my screwdriver broke the glass at bottle's neck.
so did you replace it 2 times or did someone else work on it the first time? how many miles on that car when senor failed...thanks for sharing.
I bought this cheap scan tool off of ebay for $18 4 years ago...and plugged into my nissan which broke down suddenly...just cranked but no attempt to start... This tool pin pointed it was my cam sensor ..which is very easy to change...replaced it and it started right up( this was the original plastic part my car has 121 k)...never changed my crank sensor which is same exact part on my 2005 altima...
Good Job, Keep up the Good Work!
Great job thanks to Jr. Lol
Because stuff breaks has an easier tutorial for this and covers a safety precaution. czcams.com/video/wfMZILmDPP8/video.html
How do you get the belt off the tensioner?
Can you or somebody help me please? the wire on the top at 3:13, was that plugged into anything? I took mine apart and cant find where to plug that one in???
Glad that I found this video although it didn't help with the bottle that I had an issue with today since it isn't long-necked and I couldn't get a screwdriver under the edge. I read a comment below from Robbie stating just to take a hammer to the side part and it popped off. Yay!!!
No Brasil não tem. Vai chegar daqui trinta anos.
Ok where are the cones ? Why not block that lane ???
Appreciate it, now i can sip this and get back to playing some games!
What is the light bulb number you used?
Don’t forget to steal the screwdriver too kids 😂
Huge thanks Dan! This was useful.