Video

Did u ever get ur power to work

Had this issue replaced the swervo with a remanufactured one shifted fine for a bit then it would slip randomly then go back like nothing happened now it's slipping again what can be the cause to wearing out a remanufactured swervo?

You think this would also cause a delayed shift from 1 to 2 until u let off the pedal during normal driving. But under wot, engine will redline w/o shifting to 2nd

My 700r4 slips whn cold from 1-2 an flares 2-3 in higher rpm. Iv had this servo but never installed. Guess will see if it fixes the problem or not.

Excellent video.

Just installed it and when I started the engine it shows that traction control is off and not turning on. I also found the car driving badly. Are these issues is going to get fixed after getting it tuned?

sir my gear 1 to 2 jerk and 2 to 1 as well i have spend lot of dollars but it is still the same pls assist ❤❤

Wondering why you would switch wheels. The retro one looks so much better.

Donde la tiene en que estado esta

Where can i find complete servo?

But why? I want the round steering wheel looks way better!

Thanks I hate the 2010 steering wheel looks cheap chrome fall off of the air bag cover

Good vid. But why TF anyone want a Chevy Cruise steering wheel in their Camaro 😂

Did u 15:13 ever figure out the correct left center vent P/N? I plan on doing this on my 2020 f250 but have brake controller that is mounted higher. To wards 4wd switch

Great guide, worked like a charm.

Would this cause a no shift at w.o.t and under normal driving it won't shit until around 4000 rpms and shift to 3rd from 4th when i nail it

Nice Shop, my friend is building one now the same size. He has a couple projects we will be filming for his CZcams channel.

I skimmed comments and didn’t see my answer. I really like your shop and am wondering if you’d share the total cost please?

Dang Back into the servo I go due to loosing 4 gear entirely. I picked up an amazon corvette servo for my Silverado. When installing it I jammed it in with a pry bar and it went in far could that have damaged it making it slip?

Can you swap out the stock radio face to the fully loaded one with the bigger screen?

Prefiero el 2010, el 2013 parece que manejas un Cruze o spark 😂

ahh i miss old youtube videos

What are rims ?

So where do you get a good servo from?

This is so helpful

I’m searching for the reverse of this 💀 2013 Steering wheel looks BORING compared to 2010 🔥

Are the two steering wheels the same depth? It looks like the newer wheel sits closer to the dash versus the 2010-2011 unit.

Do you know if it’s possible to swap my 10 to a 17 zl1 steering wheel ?

want to swap to a 1le sude flat bottom but they only come in manual and my 2010 is auto, will it still work? might just have to do zl1 i guess

where should I buy a servo for a 4L65e

Few months ago, when cold, 1-2 shifts firm and softens up until warmed up. I’ll get 2-3 flare as well cold or warm. 2-3 flare happens about 80% of the time. 2 weeks ago, while in OD with light pedal, truck starts to jerk like it’s slipping. It was doing it while driving on country hill roads. Filled trans fluid and it’s 1/4 above hot mark on dipstick. Added about close to half a quart. Hasn’t done OD jerking anymore but now 1-2 has soften up when cold. Will this servo fix it or does it need a rebuild? Has 157k miles.

I ditched my corvette for the superhold in my FULL build based around my Mason Smiths 4l79 billet input with every option I could find, cryo shafts included in that, extra wide Kevlar blah blah...still get random slips but ONLY at full throttle and only SOMETIMES. Really hate to pull it out as there's a 231 in its way lol...guesses? Oh- less than 6k on it, Hughes P. 28-3200..

Did you ever try these on your trailblazer ss??? What bolt pattern were they??

Did your console have a large connector that seemed to have nowhere to go?

Brother you have the best how to video’s explanations and visuals stay at it just subscribed going to spread your page around to all my friends

:(

Just did this swap in my truck but I don’t know how to get the plugs to work being they’re different wires. Any idea?

For anyone interested the price for the console itself as of 19 dec 2022 is $1,699 not including any other parts whatsoever

Too funny how you describe the gathering here . After 30 videos and I slide in here , 2nd slips a little sometimes . I'll definitely look into this solution . Here's my issue , when I shift from 4 to 3 . My 3 gear does not catch up and slow it down . I slow down and go 3 to 2 , nothing just coasts . Same from 2 to 1 . It just coasts . I can rev the engine and accelerate , but it's not actually in gear . Beer cheers

Thanks for this guide. Just swapped mine out yesterday with no issues. 🙂

I am tryiing to get one of these built now.

That new wheel is horrible. I prefer the 2010 or the 2016s

is it worth trying to replace bought a used trans and it slips from 2-3 i have a spare trans i know is good with 12,000 miles on full rebuild just broke the ears in the pump. it pulls great in any gear just slips from 2-3

Thanks!!! If there is that much leakage through the servo that explains why when I electronically max out my line pressures I get proper shifts again. I'll change it.

I could use some direction. I started this adventure of replacing my 2013 Camaro HUD. Everything was going well until I removed the steering wheel. I forgot to remove the wire harness for clock spring and pulled it apart (ribbon is hanging out) when I removed the steering wheel 😥. Do you know if there will be any issue if I just replace with a new spring unit?

2010 steering wheel looks MUCH better.

where do i buy the console at?

Thanx for the refresher! I took mine off my old GXP and the new one came with a RotoFab. I finally got around to swapping them out. I used C clip nut plates and 10mm bolts instead of push pins for the panels. Looks much better and easier to remove. I also have the update tube for the V1, the new units have it and the filter is easier to get to.

Show me how to install in my 2000 excursion lol… i wish

It shifts only till 4 gear bro?